BRAYER BR1258 Immersion Blender Instruction Manual

: June 1, 2024
: BRAYER

Table of Contents

BRAYER BR1258 Immersion Blender
Specifications

BRAYER BR1258 Immersion Blender

BRAYER-BR1258-Immersion-Blender-PROFDUCT

Specifications

Model: BR1258
Intended Use: Chopping, mixing, combined processing of liquid and solid products, frothing milk
Operation Time: 30 seconds, then rest for at least 3 minutes
Capacity: Maximum of 2/3 bowl capacity for chopping and mixing
Max Weight: 350g for fruits, 150g for hard vegetables

Product Usage Instructions

Safety Measures and Operation Recommendations
Read the operation instructions carefully before using the unit and keep them for future reference.
Do not exceed continuous operation time of 30 seconds with the attachments. Allow a 3-minute rest after 2 operation cycles.

BLENDER BR1258
The blender set is intended for chopping, mixing, and combined processing of liquid and solid products, and for frothing milk.

DESCRIPTION

Blender attachment
Attachment release buttons
Speed «TURBO» on button
ON/OFF button «ON/OFF»
Rotation speed control knob
Whisk attachment gear
Whisk attachment
Chopper geared lid
Chopping knife
Chopper bowl
Cup
Cappuccinatore attachment

$BRAYER-BR1258-Immersion-Blender- $2$$

SAFETY MEASURES AND OPERATION

RECOMMENDATIONS
Read the operation instructions carefully before using the unit, after reading keep them for future reference.

Use the unit for its intended purpose only, as it is stated in this manual.
Mishandling the unit can lead to its breakage and cause harm to the user or damage to the user’s property, which is not covered by warranty.
Make sure that the operating voltage of the unit indicated on the label corresponds to your home mains voltage.

CAUTION! Continuous operation time with the attachments should not exceed 30 seconds. After 2 operation cycles, stop using for at least 3 minutes.

Do not use the unit outdoors.
It is recommended not to use the unit during lightning storms.
• Protect the unit from impacts, falling, vibrations and other mechanical stress.
Never leave the unit connected to the mains unattended.
Do not use the unit near heating appliances, heat sources or open flame.
Do not use the unit in places where aerosols are used or sprayed, and in proximity to inflammable liquids.
Do not use the unit in proximity to the kitchen sink, in bathrooms, near swimming pools or other containers filled with water.
If the unit is dropped into water, unplug it immediately, and only then you can take the unit out of water. Apply to the authorized service center for testing or repairing the unit.
Do not let the power cord touch hot surfaces and sharp edges of furniture.

Unplug the unit after usage or before cleaning. When unplugging the unit, hold the power plug and carefully remove it from the mains socket, do not pull the power cord, as this can lead to its damage and cause a short circuit.

Do not touch the unit body, the power cord and the power plug with wet hands.
Before using the unit for the first time, thoroughly wash all the removable attachments and containers that will contact food.
Use only the parts supplied.
Do not touch rotating parts of the unit. Do not let hair or free hanging clothes get into the rotation area of the blender attachment knife or whisk.
Before using the unit, make sure that the attachments are installed properly and fixed.
Place the chopper bowl on a flat and steady surface.
Put the products into the chopper bowl before switching the unit on. Do not switch the unit on if the chopper bowl is empty.
Cool down hot products before putting them into the chopper bowl.
Watch the amount of products put in the chopper bowl and the level of poured liquids.
Cutting edges of the chopping knife and the blender attachment are sharp and dangerous. Be careful while using the chopping knife and the blender attachment.
If the chopping knife stops during the unit operation, switch the unit off, unplug it and open the geared lid, remove the product which is hindering the knife rotation. If the chopping knife or blender attachment rotation is hindered, it is recommended to add some water, juice, liquor etc. into the chopper bowl or the container used with the blender attachment.
• Remove the motor unit from the chopper bowl only after disconnecting the motor unit from the mains.
Do not place the chopper bowl and the measuring cup into a microwave oven.
Do not put the attachments and bowls in a dishwashing machine.
For children safety reasons do not leave polyethylene bags used as a packaging unattended.

ATTENTION! Do not allow children to play with polyethylene bags or packaging film. Danger of suffocation!

The unit is not intended for usage by children.
Do not leave children unattended to prevent using the unit as a toy.
Do not allow children to touch the operating surface, the unit body, the power cord or the power plug during operation of the unit.
Be especially careful if children or disabled persons are near the operating unit.
During the unit operation and breaks between operation cycles, place the unit out of reach of children.
The unit is not intended for usage by physically or mentally disabled persons (including children) or by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.
From time to time check the power cord integrity.
If the power cord is damaged, it should be replaced by the manufacturer, a maintenance service or similar qualified personnel to avoid danger.
Do not repair the unit by yourself. Do not disassemble the unit by yourself, if any malfunction is detected, and after the unit was dropped, unplug it and apply to the service center.
To avoid damages, transport the unit in the original package.
Keep the unit in a dry cool place out of reach of children and disabled persons.

THE UNIT IS INTENDED FOR HOUSEHOLD USE ONLY, DO NOT USE THE UNIT FOR COMMERCIAL OR LABORATORY PURPOSES.

BEFORE THE FIRST USE

After the unit’s transportation or storage at negative temperature, unpack it and wait for at least 3 hours before using it.

Unpack the unit and remove all the packaging materials.
Keep the original package.
Read the safety measures and operating recommendations.
Check the delivery set.
Examine the unit for damages; if the unit is damaged, do not plug it into the mains.
Make sure that the indicated specifications of the power supply voltage of the unit correspond to the specifications of your mains. When the unit is used in the mains with 60 Hz frequency, it does not need any additional settings.
Before using the unit wash the whisk attachment (7), the chopping bowl (10), the chopping knives (9), the cup (11) and the cappuccinatore attachment (12) with warm water and neutral detergent, rinse and dry them.
Wash only the lower part of the blender attachment (1), clean the outer surface with a slightly damp cloth. Never immerse the blender attachment (1) into water or any other liquids completely.
Wipe the motor unit, the chopper geared lid (8) and the whisk attachment gear (6) with a soft, slightly damp cloth and then wipe them dry.

CAUTION! Do not immerse the blender attachment (1), the motor unit, the chopper geared lid (8), the whisk attachment gear (6), the power cord and the power plug into water or any other liquids.

USING THE BLENDER ATTACHMENT

Continuous operation time of the blender attachment (1) should not exceed 30 seconds. Stop using for at least 3 minutes between two operation cycles.

Use the blender attachment (1) for making sauces, mayonnaise, fruit puree, baby food, mixing various ingredients and for processing fruit and vegetables containing enough liquid.
Before installing the blender attachment (1), make sure that the power plug is not inserted into the mains socket.
Insert the blender attachment (1) into the motor unit until the release buttons (2) clicking, make sure that the attachment is fixed properly .
Insert the power plug into the mains socket.
Immerse the blender attachment (1) into the bowl with food that you want to chop/mix; you can also put the food in the measuring cup (11).

ATTENTION! Hold the motor unit with the blender attachment (1) vertically while processing the food (pic.1).

To switch the unit on, press and hold down the button (4) «ON/OFF». Use this operation mode for mixing liquid products.
When you press and hold the button (4) «ON/OFF» you can control the attachment rotation speed by turning the control knob (5). Use this operation mode for processing of liquid and solid products.
For operation at the maximal rotation speed, press and hold down the button (3) «TURBO».

Notes

products should be put into the bowl before the unit is switched on. The amount of products to be processed should not exceed 2/3 of the capacity of the bowl in which they are processed.
before chopping and mixing peel the fruit, remove inedible parts, such as stones, and cut fruit into 15x15x15 mm cubes. Put them into a bowl and add some juice or water. The maximal amount of products should not exceed 350 g and 250 ml of water or juice.
do not chop or mix frozen food.

ATTENTION! When chopping hard vegetables, for example, car rots — cut the carrot into small 15x15x15 mm pieces and put them in the cup (11). The maximal weight of the carrot should not exceed 150g. Add 250 ml of water.

To switch the blender attachment (1) rotation off release the button (3 or 4).
• After you finish the unit operation, take the power plug out of the mains socket and remove the blender attachment (1) by pressing the release buttons (2) .

ATTENTION!

Do not remove the blender attachment (1) during the unit operation.
To avoid damaging the knives of the blender attachment (1) do not process very hard products, such as cereals, rice, coffee beans, hard cheese, frozen food etc.
If the foodstuffs are hard to chop with the blender attachment (1), add some water, juice, liquor etc.

USING THE CHOPPER
Continuous operation time of the chopper attachment should not exceed 30 seconds. Stop using for at least 3 minutes between two operation cycles.

The attachment is used to chop meat, cheese, onion, herbs, garlic, carrots, walnuts, prunes, vegetables or fruit.
ATTENTION! Do not chop very hard products, such as nutmegs, coffee beans, cereals, frozen food or ice.

PREPARING THE FOOD BEFORE CHOPPING

Remove bones, veins, cartilage and fat from meat.
Cut meat, cheese, onions, vegetables or fruit into pieces approximately 60x20x20 mm in size. Maximal weight of the meat should not exceed 200 g.
Remove stems of herbs, shell nuts.

CHOPPING

Before assembling the chopper, make sure that the power plug is not inserted into the mains socket.
Place the chopper bowl (10) on a flat and steady surface.
Install the upper chopper knife onto the lower one and turn it clockwise until bumping, install the knives (9) on the axis inside the bowl (10). If there is a protection cover on the chopping knives (9), carefully remove it.

Warning: the blades of chopping knives (9) are very sharp! Always hold the chopping knives (9) by the plastic end.

Put the products into the bowl (10).
Note: do not switch the unit on with empty bowl (10).
Place the geared lid (8) on the bowl (10) and rotate it clockwise until bumping.
Press on the locks (2) and install the motor unit on the neck of the gear cover (8), make sure that the motor unit is securely fixed. Install the motor unit vertically and evenly .
Insert the power plug into the mains socket.
To switch on, press and hold down the button (4) «ON/OFF»
When you press and hold the button (4) «ON/OFF», you can control the chopping knives (9) rotation speed by turning the control knob (5).
For operation at the maximal rotation speed, press and hold down the (3) «TURBO» button.
During operation hold the motor unit with one hand and the chopper bowl (10) with the other hand.
Release the button (3 or 4) to switch off.
After using the unit, wait until the chopping knives (9) fully stops.
Remove the power plug from the mains socket.
Disconnect the motor unit from the geared lid (8) by pressing the lock buttons (2) .
Remove the geared lid (8) from the bowl (10) by turning it counterclockwise.
Carefully remove the chopping knives (9) from the bowl (10) holding them by the plastic end.

Take the chopped products out of the bowl (10). The amount of products and the processing time

Product	Maximum weight	Time
Meat	200 g	30 seconds
Herbs	50 g	10 seconds
Almond	150 g	20 seconds
Cheese	100 g	10 seconds
Bread crumbs	80 g	10 seconds
Onions	200 g	20 seconds
Cookies	150 g	10 seconds
Soft fruit	200 g	10 seconds

USING THE WHISK ATTACHMENT

Continuous operation time with the whisk attachment (7) should not exceed 30 seconds. Stop using for at least 3 minutes between two operation cycles.

ATTENTION! Do not use the whisk attachment (7) to knead tight dough (pic.1).

Use the whisk attachment (7) only for beating egg whites, making biscuit dough or for mixing ready desserts.

Before installing the whisk attachment (7), make sure that the power plug is not inserted into the mains socket.

Insert the whisk attachment (7) into the whisk gear (6).
Insert the whisk gear (6) into the motor unit, make sure that the gear (6) and the whisk (7) are fixed properly (fig. 3).
Insert the power plug into the mains socket.
Immerse the whisk attachment (7) into a suitable bowl with food. You can put the foodstuffs into the cup (11).
To switch the unit on, press and hold down the button (4) «ON/OFF».
When you press and hold the button (4) «ON/OFF» you can control the attachment rotation speed by turning the control knob (5).
For operation at the maximal rotation speed, press and hold down the button (3) «TURBO».
Release the button (3 or 4) to switch off.
After you finish using the unit, disconnect the power plug from the mains socket, and disconnect the whisk gear (6) from the motor unit.
Remove the whisk attachment (7) from the gear (6).

CAPPUCCINATORE ATTACHMENT
The continuous operation time of the campus center attachment (12) should not exceed 30 seconds. After 2 operation cycles, stop using for at least 3 minutes.

The cappucci natore attachment (12) is used only for milk frothing.
Before installing the attachment (12), make sure that the power plug is not inserted into the mains socket.
Insert the attachment (12) into the gear (6).
Insert the gear (6) into the motor unit until the locks (2) clicking and make sure that the gear (6) and the attachment (12) are fixed properly .
Insert the power plug into the mains socket.
Put the attachment (12) into a suitable container with cold milk or cream. You can put the foodstuffs into the cup (11).
To switch on, press and hold down the button (4) «ON/OFF».
When you press and hold the button (4) «ON/OFF», you can control the campus cinatore attachment (12) rotation speed by turning the control knob (5).
For operation at the maximal rotation speed, press and hold down the (3) «TURBO» button.
Release the button (3 or 4) to switch off.
After you finish using the unit, take the power plug out of the mains socket, and disconnect the gear (6) from the motor unit by pressing the lock buttons (5) .
Remove the campus center attachment (12) from the gear (6).

CLEANING

CAUTION! The blades of the chopping knives (9) are very sharp and may be dangerous. Handle the chopping knives (9) with extreme caution!

Remove the power plug from the mains socket after using the unit.
Wash the whisk attachment (7), the chopping bowl (10), the chopping knives (9), the cup (11) and the cappu ccinatore attachment (13) with warm water and neutral detergent, rinse and dry them.
Wash only the lower part of the blender attachment (1), clean the outer surface with a slightly damp cloth. Never immerse the blender attachment (1) into water or any other liquids completely.
Wipe the motor unit, the geared lid (8) and the whisk attachment gear (6) with a soft slightly damp cloth and then wipe them dry.
After processing salty or sour products, it is necessary to rinse the blender attachment (1) or the chopping knives (9) with water immediately.
While possessing products with dyeing properties (for instance, carrot or beetroot) the attachments and bowls can get colored, wipe the attachments and the bowls with a cloth, dampen in vegetable oil; after that wash the attachments and bowls with a neutral detergent, rinse and dry them.
Do not immerse the motor unit, the gear (6), the geared lid (8) into any liquids, do not wash them under water jet or in a dishwashing machine.
Do not use abrasives and solvents to clean the motor unit body and the removable parts.

STORAGE

Clean the unit parts before taking it away for long storage.
Do not wind the power cord around the motor unit.
Keep the unit in a dry cool place out of reach of children and disabled persons.

DELIVERY SET

Motor unit – 1 pc.
Blender attachment – 1 pc.
Whisk gear – 1 pc.
Whisk attachment – 1 pc.
Geared lid – 1 pc.
Chopping knives – 2 pcs.
Chopping bowl – 1 pc.
Measuring cup – 1 pc.
Cappuccinatore attachment – 1 pc.
Instruction manual – 1 pc.

TECHNICAL SPECIFICATIONS

Power supply: 220-240 V, ~ 50-60 Hz
Rated input power: 1500 W
Cup – 800 ml
Chopper bowl – 600 ml

RECYCLING

To prevent possible damage to the environment or harm to the health of people by uncontrolled waste disposal, after the expiration of the service life of the unit or the batteries (if included), do not discard them with usual household waste, take the unit and the batteries to specialized stations for further recycling.
The waste generated during the disposal of products is subject to mandatory collection and consequent disposal in the prescribed manner.
For further information about recycling of this product apply to a local municipal administration, a household waste disposal service or to the shop where you purchased this product.

The manufacturer reserves the right to change the design, structure and specifications not affecting general operation principles of the unit, without prior notice.

The unit operating life is 3 years
The manufacturing date is specified in the serial number.
In case of any malfunctions, it is necessary to apply promptly to the authorized service center.

Hergestellt für «Ruste GmbH», Berggasse 18/18, 1090 Wien, Osterreich
Produced for «Ruste GmbH», Berggasse 18/18, 1090 Vienna, Austria