AIGOSTAR 9-BLADE Pedestal Stand Fan Instruction Manual
- June 14, 2024
- aigostar
Table of Contents
AIGOSTAR 9-BLADE Pedestal Stand Fan
IMPORTANT SAFETY INSTRUCTIONS
-
Use the fan only for the purposes described in this instruction manual.
-
To protect against electric shock, do not immerse the fan, its plug or its cord in water or any other liquid or spray it with liquid.
-
Close supervision is necessary when the fan is being used by or near children or near pets.
-
Unplug the fan from the electrical outlet when not in use, when moving it from one location to another, before putting on or taking off parts, and before cleaning.
-
Avoid contact with any moving parts.
-
Do not operate the fan if it has a damaged cord or plug, if it has malfunctioned or it it has been dropped or damaged in any manner.
-
The use of attachments not recommended or sold by the appliance manufacturer may cause hazards.
-
Do not use the fan outdoors.
-
To disconnect the fan from the electrical supply, grip the plug and pull it from the wall outlet.
DO NOT pull on the cord. -
Always use the fan on a dry, level surface.
-
If the power supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
-
.This fan is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or who lack experience or knowledge unless they have been given supervision or instruction concerning its use by a person responsible for their safety.
-
Children should be supervised to ensure that they do not play with the fan. 14.Unplug the appliance before disassembling fan grille.
-
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
-
Do not run the cord under carpeting. Do not cover cord with throw rugs, runners or similar coverings. Do not route the cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
TECHNICAL SPECIFICATIONS
- Model No.
- 830101GU2
- Power Supply
- 120V – 60HZ
- Power Consumption
- 5SW
Specifications and design are subject to change without notice.
PARTS DIAGRAM
ASSEMBLY INSTRUCTIONS
-
Align the screw positions and place the base cover on the balancing block, fix the nut to the screw holes at the bottom of the balancing block, turn the screws clockwise to fix the pole on the base.
-
Unscrew the height adjustment ring to loosen it, then slide down the screw cover. Lift the internal pole to the maximum height while preventing the internal pole from slipping into the extension pole. Then, reattach the height adjustment ring and tighten.
Note : Loosen the height adjustment ring to adjust the internal pole to the desired height.
( Note : If you cannot find the internal pole, it has slid inside the column pole; pull it out from inside the column pole.) -
To attach the head unit to the internal pole, loosen the cinquefoil screw at the bottom of the head unit. Place the head unit onto the internal pole and tighten the cinquefoil screw clockwise.
-
Loosen the mounting nut, attach the rear grille to the motor well, then tighten the nut clockwise.
-
Mount the blade onto the shaft. Make sure that the motor shaft pin fits into the groove of the blade. Turn the spinner anticlockwise to tighten the blade. 6.Align the front grille to the rear grille according to the screw positions. Fasten the front grille to the rear grille by locking the 3 screws and make sure the grille will not loose
OPERATING INSTRUCTIONS
- Set the fan on a dry, level surface.
- Plug the power cord into any standard 220-240V ~ AC power outlet.
- Operate the fan by buttons on the control panel or the remote controller.
| ON/SPEED | Turn on the fan/Adjust wind speed |
|---|---|
| SWING | The fan swings left and right |
| MODE | Adjust wind mode |
| TIME | Timing O.SH-7.SH |
| OFF | Shut down the fan |
| ON/SPEED | Press once to turn on the fan, press again to adjust wind speed |
| --- | --- |
| SWING | The fan swings left and right |
| TIMER | Enter timing mode and select the timing time |
Natural/Sleep/ Normal modes
|
- Natural/Sleep mode
- Use remote controller to select natural/sleep wind mode, the corresponding indicator will turn on. The normal mode is default setting without indicator display.
OFF| The fan stops working
Tilt control : The air flow can be adjusted upward or downward by tilting the fan head manually as desired.
CLEANING AND MAINTENANCE
- Always unplug the fan before cleaning, assembly or disassembly.
- Do not allow water to drip on or into the fan motor housing.
- Use a soft cloth moistened with a mild soap solution to clean the fan.
- Do not use petrol, thinners or benzene as a cleaner.
- WARRANTY : 1 YEAR
- AIGOSTAR INC
- 489 YORBITA RD, CITY OF INDUSTRY,
- CA 91744 (UNIT A)
- HTTP://WWWAIGOSTAR.COM
- MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>