Electrolux FPFU19F8WF Single Door Refrigerator Stainless Steel Instruction Manual

Electrolux FPFU19F8WF Single Door Refrigerator Stainless Steel

Specifications

• Product Name: Filtered Ice Kit
• Model Number: TTFLTRICEKIT
• Compatible Models: FPFU19F8WF, FPRU19F8WF, EI33AF80WS, EI33AR80WS
• Kit Contents:
  • 1x Instruction Sheet
  • 1x A19408101 Wiring Harness (19 feet)
  • 2x 305346-00 Wiring Harness Support Clips
  • 1x 1/4 Union 5304518370
  • 1/4 Green Water Line (16 feet)
  • 1/4 Green Water Line (16 feet)
  • 1/8 Wiring Harness Strain Relief
  • 1/8 Wiring Harness Strain Relief

Product Usage Instructions

Access Cover Removal:

• Tools Required: 1/4 nut driver
• Steps:

1. Remove the 8 access panel screws on the refrigerator and Freezer.
2. Apply the protective rubber trim to the inside edge of the water valve opening on both access covers.

Refrigerator Connections:
Steps:

1. Feed the green water line and wiring harness through the opening of the refrigerator access cover.
2. Push the green water line into the green port of the water valve.
3. Connect the wiring harness to the connector on the refrigerator.
4. Locate wiring harness support clip at the top of the refrigerator machine compartment and insert the wiring harness to secure.

Freezer Connections:
Steps:

1. Disconnect the gray water line from the water valve and install a union fitting on the end of the line.
2. Feed the green water line and wiring harness coming from the refrigerator through the opening of the access cover.
3. Connect the green and gray water line into a 1/4 union to join them together.
4. Disconnect the harness connection from the water valve (not required).
5. Reinstall access cover for both units.

Water Line Final Connections:
Steps:

1. Fasten the strain reliefs for green water line and wiring harness on each unit.
2. Attach the adhesive support clips and insert the green water line and harness.
3. Loop the water line and wire harness in the center of the two units.

Frequently Asked Questions (FAQ)

• Do I need a professional to install this kit?
  Yes, it is recommended to have an authorized service technician install the filtered ice kit.

• What tools are required for installation?
  You will need a 1/4 nut driver for installation.

• Can I use this kit with any refrigerator model?
  This kit is designed to provide filtered water to the freezer ice maker when a single-door freezer is installed next to a single-door refrigerator. Please check compatibility with your specific models listed in the manual.

Kit Contents

ORIGINAL CONFIGURATION

NOTE: This kit is designed to provide filtered water to the freezer ice maker when a single-door freezer is installed next to a single-door refrigerator.
NOTE: An authorized service technician is recommended to install the filtered ice kit.
NOTE: Disconnect electrical power prior to servicing this product.
Tools Required: 1/4” nut driver

Access Cover Removal

CAUTION: Wear gloves and use extreme CAU-TION when installing the PROTECTIVE rubber trim. The opening may have sharp edges.

1. Remove the 8 access panel screws on the refrigerator and Freezer.

2. Apply the protective rubber trim (D) to the inside edge of water valve opening on both access covers.

Refrigerator Connections

1. Feed the green water line (A) and wiring har-ness (E) through the opening of the refrigerator access cover.
2. Push the green water line into the green port of the water valve.

3. Connect the wiring harness (E), to the connec-tor on the refrigerator.
4. Locate wiring harness support clip at top of refrigerator machine compartment (F), and insert wiring harness to secure.

Freezer Connections

NOTE: The freezer water valve and the connect-ing harness are not used when this kit is installed for filtered water provided by the paired refrigera-tor.

1. Disconnect the 10″ Gray water line from the water valve by pushing upward on the port tab, while pulling out the line. Install union fitting on the end of the gray line.

2. Feed the green water line (A) coming from the refrigerator along with the wiring harness (E) through the opening of the access cover.

3. Push the green and gray water line into 1/4″ union (G) to connect the two together.

4. Connect the harness (E) from the refrigerator to the connector for the freezer. Locate wiring harness support clip at top of refrigerator ma-chine compartment (F), and insert wiring harness to secure.

5. Disconnect the harness connection from the water valve. Not required. Water will be supplied from the refrigerator water valve.

6. Reinstall access cover for both units.

Water Line Final Connections

1. Fasten the strain reliefs for green water line (B) and for wiring harness on each unit. (C)

2. Attach the two adhesive support clips (F) and insert the green water line and harness.

3. Loop the water line and wire harness in the center of the two units.

4. Connect and turn on water supply.

5. Purge air from water lines by dispensing water from refrigerator water dispenser. (See Use and Care manual for details on water dispenser operation and purging method)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>