DIG LEIT WWSE Ambient Light Powered Wireless Weather Station Instruction Manual
- June 6, 2024
- DIG
Table of Contents
LEIT WWS and LEIT WWSE
Ambient Light Powered Wireless
Weather Station
INSTRUCTION MANUAL
Introduction
Thank you for purchasing DIG’s LEIT WWS (with wind sensor) or LEIT WWSE (without wind sensor) wireless, ambient light (solar) powered weather station, which operates as a part of the LEIT-2ET wireless, ambient light (solar) powered irrigation system. This manual describes how to get the LEIT WWS or LEIT WWSE weather station up and running quickly. After reading the manual and becoming familiar with the basic functions of the weather station, the user can refer to the manual for less common tasks in the future.
About the LEIT WWS and LEIT WWSE Weather Stations
DIG’s LEIT WWS and LEIT WWSE wireless weather stations are independent,
column-mounted, weather measuring instruments powered by ambient light
(solar). The LEIT WWS and LEIT WWSE weather stations continually gather data
on weather conditions from the surrounding area and simultaneously transmit
the data once every hour during daylight hours to any LEIT-2ET and/ or LEIT
XRC-ETS controller at a distance of up to 350’ (100 m) line of sight. The
weather data collected and transmitted by the weather station’s sensors are
used in the calculation of the daily local microclimate evapotranspiration
(ET).
The LEIT-2ET weather-based wireless irrigation control system comprises the
LEIT-2ET weather-based two-station ambient light (solar) powered irrigation
controller with a rain sensor connection, the LEIT RC2ET handset, and the LEIT
WWS or LEIT WWSE ambient light (solar) powered weather station. Site
information is entered into the LEIT RC2ET handset and is downloaded into the
LEIT-2ET controller. With the site information and the hourly weather data
received from the LEIT WWS or LEIT WWSE weather station, the LEIT2ET
controller calculates the daily local microclimate evapotranspiration (ET) and
uses it to make a daily adjustment or override of the scheduled irrigation
program.
NOTE: The LEIT WWS and LEIT WWSE wireless weather stations’ weather
condition data can be reviewed by the LEIT RC2ET remote handset. After
installation, no further visits to the weather stations are required.
Unit Identification
INSTRUMENTS:
LEIT WWS includes an anemometer, thermometer, hygrometer, rain collector, and
solar radiation meter to monitor humidity level, temperature, wind speed,
solar radiation, and rainfall.
LEIT WWSE includes: thermometer, hygrometer, rain collector, and solar
radiation meter to monitor humidity level, temperature, solar radiation and
rainfall.
IMPORTANT: Communication between the LEIT RC2ET handset, the LEIT-2ET
controller, the LEIT WWS, and the LEIT WWSE weather station is automatically
limited to daylight hours when there is sufficient light energy. Longer,
brighter light days will enable the system to operate over extended parts of
the day.
Technical Assistance
Should you encounter any problem(s) with this product or if you do not
understand its many features, please refer to this operating manual first. If
further assistance is required, DIG offers the following customer support:
Technical Assistance the USA
DIG’s Technical Service Team is available to answer questions from 8:00 AM to
5:00 PM (PST), Monday-Friday (except holidays) at
1-800-322-9146.
Questions can be emailed to: questions@digcorp.com or
faxed to 760-727-0282.
Specification documents and manuals are available for download at:
www.digcorp.com.
For customer assistance outside the USA, contact your local distributor.
Copyright and Compliance
Copyright 2010 DIG Corporation. All rights reserved. LEIT-2ET and LEIT RC2ET
are each trademark of DIG Corporation. Patent pending.
FCC, IC, CE certified, Australia and Hong Kong compliance
To comply with FCC RF exposure compliance requirements, the antenna used for
this transmitter is installed to provide a separation distance of at least 8
inches (20 cm) from all persons (not including hands, wrist, feet, and ankles)
and must not be co-located or operated in conjunction with any other antenna
or transmitter.
This device is required to comply with FCC RF exposure requirements for mobile
and fixed transmitting devices. This model transceiver generates and
uses radiofrequency energy. If not installed and used in accordance with the
manufacturer’s instructions, it may cause interference with radio and
television reception.
CONTROLLER FCC ID: UJV-LEIT01 IC: 6694A-LEIT01
HANDSET FCC ID: UJV-LEIT02 IC: 6694A-LEIT02
WEATHER STATION FCC ID: UJV-LEIT03 IC: 6694A-LEIT03|
---|---
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy. If not installed and used in accordance with the
instructions, the remote may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult DIG technician for help.
WARNING: the user should make no field changes or modifications to the LEIT WWS or LEIT WWSE weather stations. All adjustments and changes must be made at DIG’s facility under the specific guidelines suggested in our instruction manual. Any tampering or modification to the equipment will void the user’s authority to operate the unit, rendering the equipment in violation of FCC part 15, and will void the warranty.
Features
- Power is provided by an efficient photovoltaic module (PVM) and microelectronic management system fueled by ambient light (solar)
- Weather data transmitted from the weather station is stored by the controllers and reviewable by LEIT RC2ET handsets
- The weather station ID number enables any controller in range to differentiate among multiple weather stations allowing the controller to receive information from several weather stations
- Based on user input and information collected from the weather station sensors, a LEIT-2ET controller performs the calculations needed to override or adjust the daily scheduled irrigation program to compensate for evapotranspiration (ET)
- Environmentally friendly utilizes RoHS compliant components
- The LEIT weather stations utilize radio frequency in the ISM band 902-928 MHz (866 Hong Kong, 868 International) CE, IC, FCC certified, Australia and Hong Kong compliant
- The LEIT weather station’s electronic components and sensors are completely waterproof
- The rain gauge is a self-emptying tipping bucket reading rainfall in 0.01 inch (.254 mm) increments
- The LEIT weather station’s three-plate radiation shield is specially designed to protect the sensors from reflected and radiated heat
- The LEIT WWS and LEIT WWSE weather stations can provide information to the LEIT ET controllers to completely stop irrigation if it is raining, freezing or too windy
- Current weather data is provided to LEIT-2ET controllers daily, every hour, during daylight hours only
- The weather stations function both day and night in any weather and in most outdoor locations and only transfer weather data during daylight hours
- Rugged and lightweight plastic construction
- Three-year manufacturer’s warranty
Technical Specifications:
- Weather Station power requirements for normal operation: Minimum of 3,000 LUX
- PVM power output 35 W/M² at 100,000 LUX (231 W/M² ) +/- 20%
- Input: 3,000-100,000+ LUX
- Wireless transmitter power and frequency specifications: -7 dBm @ 920 MHz / 7 dBm @ 868 MHz / -7 dBm @ 866 MHz
Sensor Specifications:
-
Humidity range and resolution: 1 to 99%
° Relative humidity accuracy: +/- 2% -
Temperature resolution and accuracy: -40° F to +170° F (-40° F to +77° C) +/- 1% resistance tolerance
-
Wind speed resolution and accuracy: Minimum speed 0 MPH (KPH) max speed 30 MPH (49 KPH) +/- 1%
-
Rainfall resolution and accuracy: .01 inches accuracy +/- 2% @ 2” (51 mm) per hour
Dimension and Connections:
- Weather station size: W 6.07”x H 9.5” x D 14.5” (W 154 mm x H 241 mm x D 368 mm)
- Rain collector size: W 5.13” x H 4.09” (W 130 mm x H 104 mm) [16.5 sq. in. (41.9 sq. cm)]
- Mounting connection: 1” x 12” mounting column and integrated clamp with two screws for mounting onto 1 1/2” galvanized pipe mounting column [recommended height; minimum 8 ft. (2.4 m)]
System
1.1 Box Contents
- Weather sensor model LEIT WWS with wind sensor or LEIT WWSE without wind sensor
- 12” (30 cm) mounting galvanized steel column used with mounting bracket
- Two clamps
- 1 1/2” mounting bracket
1.2 Parts Identification
- PVM (photovoltaic module) harnesses the energy of light and generates the electricity to power the unit day and night in any weather condition
- Self-emptying, tipping bucket rain gauge
- Weather sensor shield to protect the temperature sensors
- Wind sensor
- 12” mounting galvanized steel column
- 1 1/2” mounting bracket with two clamps
1.3 System Components
To properly install the LEIT WWS or LEIT WWSE weather stations, the following
components will be needed:
- Weather station unit: LEIT WWS or LEIT WWSE ambient light (solar) powered wireless weather station
- Mounting connection: 1” x 12” mounting column and integrated clamp with two screws (included)
- 1 1/2” mounting column with a recommended height with a minimum of 8 ft (2.4 m) (not included)
1.4 Tools and Supply Requirements
- Philips screwdriver (#2) if using the mounting column plastic attachment and 7/16” wrench or socket to tighten the U clamp to the 1 1/2” pipe
- Concrete: approximately four to five 60 lb (27 kg) cement bags
Installation
NOTE: Install the LEIT WWS and/or LEIT WWSE at a minimum of 25 ft (8 m)
from the nearest LEIT-2ET controller.
Install the weather station 8-12 ft. (2.4 m – 3.7 m) above the ground using a
1 1/2” pipe mounting column. Set the mounting column in a 15” x 15” x
12” (38 x 38 x 30 cm) frame and pour in the four to five 60 lb (27 kg) bags of
cement. After the cement is dry, mount the weather station on the top of the
mounting column following the steps below (see Figure A):
STEP 1: Insert the 12” column (included) into the weather station column
holder and secure the clamp with the two screws.
STEP 2: Insert the assembly into the plastic mounting bracket and secure
it with the provided screw.
STEP 3: Mount the assembly to the 1 1/2” column and secure using the two
clamps included
STEP 4: Cap off the end of the 1 1/2” pipe using a 1 1/2” galvanized cap.
Make sure the column is vertical to allow the rain gauge to operate properly.
No setting, programming, or wire connection is required.
After installation and after the weather station is fully powered, it will start transmitting weather data information every hour.
Quick Operation Review
In order to establish communication for the first time between a LEIT RC2ET remote control handset, LEIT-2ET two station weather-based ambient light (solar) powered wireless irrigation controller, and the LEIT WWS or LEIT WWSE weather station, the following steps must be taken:
- Charge the LEIT RC2ET remote control handset (see LEIT RC2ET instructions).
- Set up the LEIT RC2ET handset (see LEIT RC2ET instructions).
- Install the LEIT-2ET controller following the LEIT-2ET installation instructions and let it sit out in the light to harness light energy.
- Install the LEIT WWS (with wind sensor) or LEIT WWSE (without wind sensor) weather station following the installation instructions and allow the weather station to sit out in the light to harness light energy.
a. In bright light conditions (full sun) it will take approximately 30 minutes.
b. In shaded conditions it could take up to 2 hours.
NOTE: Communication between the remote control handset and the controller will only initiate when the controller is fully charged. Communication between the controller and the weather station will initiate every hour, in daylight hours only, and only if the controller ET feature is activated (wind sensor and rain sensor are set active by user).
Maintenance
The LEIT WWS and LEIT WWSE weather stations are waterproof units, designed for
outdoor use. In order to keep the weather stations clean and
functioning correctly, cleaning the clear plastic above the PVM panel and the
solar radiation sensor every 6-12 months is recommended.
Warranty
DIG CORPORATION warrants these products to be free from defects in material
and workmanship for a period of three years from the date of purchase. This
warranty does not cover damage resulting from accident, misuse, neglect,
modification, or improper installation. This warranty shall extend only to the
original purchaser of the product for use by the purchaser. The obligation of
DIG CORPORATION under this warranty is limited to repairing or replacing at
its factory this product shall be returned to the factory within three years
after the original purchase and which on examination is found to contain
defects in material and workmanship.
DIG CORPORATION SHALL IN NO EVENT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND; THE SOLE OBLIGATION OF DIG BEING LIMITED TO
REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS. SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
Unattended use for prolonged periods without inspection to verify proper
operation is beyond the intended use of this product, and any damage resulting
from such use shall not be the responsibility of DIG CORPORATION. There are no
warranties that extend beyond the description on the face hereof. In the case
of purchase of the product for use other than, for irrigation purposes, DIG
CORPORATION hereby disclaims any implied warranties including any warranties
of merchantability and fitness for a particular purpose. In the case of the
purchase of the product for personal, family or household purposes, DIG
CORPORATION disclaims any such warranties to the extent permitted by law. To
the extent that any such disclaimer or implied warranties shall be
ineffectual, then any implied warranties shall be limited in duration to a
period of three years from the date of the original purchase for use by the
purchaser. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you.
In order to obtain performance under this warranty, the unit must be returned
to the factory, along with proof of purchase indicating original date of
purchase, shipping prepaid, addressed as follows:
DIG CORPORATION, 1210 Activity Drive, Vista, CA 92081-8510. Repaired or
replaced units will be shipped prepaid to the name and address supplied with
the unit returned under warranty. Allow four weeks for repairs and shipping
time. Repair of damaged units not otherwise within warranty may be refused or
done at a reasonable cost or charge at the option of DIG CORPORATION.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
1210 Activity Drive
Vista, CA 92081-8810, USA
Website: E www.digcorp.com
e-mail: dig@digcorp.com
010510 DIG CORP 26-090
Printed in the USA
DIG is a Registered Service Mark of DIG Corp.