FENIX LD12R Dual Light Sources Multipurpose Portable Flashlight User Manual

FENIX LD12R Dual Light Sources Multipurpose Portable Flashlight

Instruction

WARNING

• * Do NOT shine the flashlight directly into the eyes of anyone!

  • Do NOT place light head near flammable objects. high temperatures can
  • cusecs to overheat and become flammable/ignite!
  • Do NOT j use the flashlight in inappropriate ways such as holding the unit in  your mouth, doing so could cause serious personal injury or death if the flashlight or intemal battery fails!
  • This flashlight will accumulate a significant amount of heat while operating, resulting in a high temperature of the flashlight shell. Pay close attention to avoid burns.
  • Remove the battery from the flashlight to prevent accidental activation when the flashlight is placed in a closed-in and flammable environment such as pockets and backpacks’
  • The LED of this flashlight is not replaceable; so the whole flashlight wil( need to be replaced when the LED reaches the end of its lifespan

(ENGLISH)FENIX LD12R FLASHLIGHT

• * 600 lumens maximum output, 186 meters maximum beam distance.

  • Uses high-quality LEDs with a lifespan of 50000 hours.
  • Convenient flashlight head rotary design for swiftly choosing between the main light and the sidelight.
  • Included is one ARB-L 14-800 battery, the LD12R is compatible with a single AA Ni-MH or Alkaline battery.
  • Hidden USB Type-C charging port.
  • Battery level indication LED and low-voltage warning.
  • Included magnetic body clip for hands-free, convenient operation.
  • Compaq Uble with Fenix AOD-S V2.0 diffuser tip for different lighting demands
  • Intelligent overheat protection circuitry to protect against high surface temper­ature.
  • All-metal CNC machined light body.
  • Premium type Hailie hard-anodized anti-abrasive finish.
  • IP68 rated protection.
  • Size: 4.76″ x 0.87” x 0. 75″1121 “22” 19 mm.
  • Weight:2.61 ozfl4 g (including battery).

OPERATING INSTRUCTION

• * On/off

  • Fully press the tail switch to turn on or turn off the flashlight.
  • Mode switching
  • With the light switched on, loosen the light head until the light goes off, then
  • tighten thelight head again to switchbetween themain light andthe side light.
  • Output Selection
  • Main light: With the light switched on, tap the tail switch to cycle through Moonlight–+LOW–+Med–+High.
  • Side light: With the light switched on, tap the tail switch to cycle through Low-­Med-High

TECHNICAL PARAMETERS

Not &: The above specifications are the test results produced by Fenix through its laboratory sing the Fenix ARB-L 14-800 battery under the temperature of 21:1:J•c and humidity of 50% – 80%

•Toe High output is measured in total of rune including output at reduced levels due to the built-i temperature protection mechanism

Intelligent Memory Circuit

The main light memorizes the last selected output. With the light switched off for over 1 second, turn on the light again and the previously used output will be recalled.

Type| Dimensions| Nominal Voltage| Usability|
---|---|---|---|---
Fenix ARB-L14 Series| 14500″| 3.6V| Recommended| .J.J
Ni-MH battery| AA..| 1.2V| Usable|
Alkaline battery| AA..| 1.5V| Usable|
Non-rechargeable Battery(lithium)| AA”| 1.SV| Usable|

·14500 Li-ion batteries are powerful cells designed for commercial applications and must .

The high output of main light cannot be operated while using the AA battery.

BATTERY REPLACEMENT

Unscrew the tail cap and insert the battery with the anode side(+) towards the light head, then screwed tail cap beckon.

CHARGING

1. With the light switched off, loosen the light head to reveal the USB Type-C charging port and plug the USB A socket of the charging cable into an approved USB powered outlet. then connect the USB Type-C socket of the charging cable to the light.
2. The indicator will display red while charging, and will tum to green when fully charged
3. Once charging has completed, be sure to lighten the light head to maintain the dustproof and waterproof functionality.
4. The normal charging lime of the included Fenix ARB-L1 4-800 battery is approximately 2 hours from depleted to fully charged with the light off. The flashlight cannot be operated while charging

BATTERY LEVEL INDICATION

• * Loosen the light head to reveal the battery indicator. Press the switch, the battery

  • indicator will flash for 3 seconds to show the remaining battery power.
  • Green light on: saturated 100% – 85%
  • Green light ftashes:sufficient85%-50%
  • Red light on: poor 50% – 25%
  • Red light flashes:critical 25%-1%
  • Note: This feature only works with a Fenix ARB-L 14 Series battery

INTELLIGENT OVERHEAT PROTECTION

The flashlight will accumulate a lot of heat when used at high output levels for extended periods. The light will automatically step down a few lumens to reduce the temperature to a sea-level when this situation occurs.

LOW-VOLTAGE WARNING

When the voltage level drops below the preset level, the flashlight is programmed to downshift to a lower brightness level until Moonlight output is reached. When Moonlight output is reached, the light blinks 3 times every 5 minutes to remind you to recharge or replace the battery.
Note: This feature only wor1i:s with a Fenix ARB-L 14 Series battery.

USAGE AND MAINTENANCE

• * Disassembling the sealed head can cause damage to the light and will void the warranty.

  • Fenix recommends using an excellent quality battery.
  • If the light will not be used for an extended period. remove the battery, or the light could be damaged by electrolyte leakage or battery explosion’s
  • Remove the battery to prevent accidental activation during storage or transportation.
  • Long-term use can result in 0-ring wear. To maintain a proper water seal, replace theringwithan approved spare
  • Periodic cleaning of the battery contacts improves the lamp’s performance as dirty contacts may cause the lamp to flicker. shine intermittently or even fail to illuminate forthe following reasons·
  • Poor battery level.
  • Solution: Replace or recharge the battery (Ensure the battery is inserted according to the manufacturer’s specifications).
  • B: The threads, PCB board contact or other contacts are dirty Solution: Clean the contact points with a cotton swab soaked in rubbing alcohol
  • If the above methods don’t work, please contact your authorized distributor.

INCLUDED

Fenix L012R flashlight, A RB-L1 4-800 battery, USB Type-C charging cables pare 0-ring,Lanyard,User manual, Warranty card “Follow” us for more information about Fenix.

FENIXLIGHT LIMITED
Tel: +86-755-29631163/83/93
Fax: +86-755-29631181
E-mail: info@fenixlight.com
Web: www.fenixlight.com Address: 2F/3

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>