AVITEC 110450 Flagpole Holder Instruction Manual

: June 15, 2024
: AVITEC

Table of Contents

AVITEC 110450 Flagpole Holder
Product Information
Product Usage Instructions
FAQ
IMPORTANT SAFETY INFORMATION
Limited Warranty
Setting Up
Contacts
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AVITEC 110450 Flagpole Holder

AVITEC-110450-Flagpole-Holder-product.

Product Information

Specifications

Model: Flagpole Holder Model 110107
Model: Umbrella Holder Model 110450
Manufacturer : AVITEC
Copyright: © 2023 by AVITEC

Important Safety Information

This product comes with important safety instructions that must be followed to avoid potential personal injury hazards. Please read and understand all safety warnings and instructions before assembling, installing, operating, or servicing this product.

Unpacking

Upon receiving the shipment, it is essential to thoroughly inspect the package. The signed bill of lading serves as an acknowledgment of receipt in good condition. If any of the goods are shorted or damaged, do not accept them until the carrier makes a notation on the freight bill. In case of any hidden loss or damage discovered after receipt, please notify AVITEC immediately.

Personal and Work Area Safety

When using this product, it is important to prioritize personal and work area safety. Follow these guidelines:

Always wear ANSI approved safety goggles to protect your eyes.
Wear hearing protection when working in noisy environments to prevent hearing loss.
Use appropriate safety equipment such as safety shoes, hard hat, and work gloves based on the applicable conditions.
Dress appropriately by avoiding loose clothing, containing long hair, and keeping hair, clothing, and gloves away from moving parts.
Use common sense when working by staying alert and concentrating on the task at hand.
Ensure the work area is clean and well-lighted during setup and usage of the product. Keep spectators and children out of the workarea.

Product Usage Instructions

Assembly

Follow these steps to assemble the Flagpole Holder or Umbrella
Holder:

Gather all the components required for assembly. Refer to the parts catalog for a detailed list.
Identify the base and pole sections.
Attach the pole sections together, ensuring they are securely fastened. Position the base on a stable surface and secure it in place using the provided screws or fasteners.
Attach the pole to the base, following the instructions provided. Perform a final check to ensure all connections are tight and secure.

Installation

Follow these steps to install the Flagpole Holder or Umbrella Holder:

Select a suitable location for installation, considering factors such as stability and visibility.
If necessary, prepare the installation area by clearing any obstructions or debris.
Place the assembled holder in the desired position.
Securely attach the holder to the ground or mounting surface using the appropriate methods outlined in the instructions.
Verify that the holder is stable and properly installed before proceeding.

Maintenance

To ensure optimal performance and longevity of the Flagpole Holder or Umbrella Holder, regular maintenance is recommended.

Follow these guidelines:

Inspect the holder periodically for any signs of wear, damage, or loose connections.
Clean the holder using a mild detergent and water solution, avoiding abrasive cleaners or solvents.
Tighten any loose connections and replace any worn-out components as necessary.
Store the holder in a dry and protected area when not in use.

FAQ

Q: Can the Flagpole Holder and Umbrella Holder be used interchangeably?
- A: No, the Flagpole Holder and Umbrella Holder are designed for specific purposes and should not be used interchangeably.
Q: Are the required assembly tools included with the product?
- A: The assembly and maintenance tools may not be included with the product. Please refer to the manual for a list of required tools.
Q: How should I store the holder when not in use?
- A: It is recommended to store the holder in a dry and protected area to prevent damage from weather conditions or other external factors.

Read and understand this entire manual before assembling, installing, operating, or servicing this product.

SAVE THIS MANUAL

Copyright 2023 by AVITEC. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of AVITEC. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and maintenance may not be included.

IMPORTANT SAFETY INFORMATION

This is a SAFETY ALERT symbol.

It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

DANGER

indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE

indicates important information which, if not followed, may cause damage to equipment.

SAVE THIS MANUAL

Keep this manual for the safety warnings tant information on how to assemble, use and maintain this product.
Write the product’s model number and pur-chase date on the cover page of this man-ual. Keep this manual (and your purchase receipt) in a safe place.

UNPACKING

The shipment should be thoroughly inspected as soon as it is received. The signed “bill of lad-ing” is acknowledgement by the carrier of receipt in good condition of shipment covered by our invoice. For your own protection, if any of the goods called for on the bill of lading are shorted or damaged, do not accept them until the carrier makes a notation on the freight bill of the shorted or damaged goods.

Notify AVITEC immediately if any hidden loss or damage is discovered after receipt.

WARNING: concerning Risk of Eye Injury. Wear ANSI approved eye protection.
WARNING: concerning Risk of Hearing Loss. Wear hearing pro-tection.

IMPORTANT SAFETY INSTRUCTIONS

Read and understand all safety warnings and in structions.

Failure to follow the warnings and instructions may result in serious injury or death. Save all warnings and instructions for future reference.

**Personal and Work Area Safety**

Always wear ANSI-approved safety goggles.
Always wear hearing protection when working in noisy environments. Prolonged exposure to high-intensity noise can cause hearing loss.
Use safety equipment. Safe- ty shoes, a hard hat and work gloves must be used for applicable conditions.

Dress appropriately

Never wear loose fitting clothing or jewelry when working.

Contain long hair, and keep hair, clothing and gloves away from moving parts.

Use common sense when working

Stay alert and concentrate when setting up and using either the Umbrella Holder or the Flagpole Holder. Never work while under the influence of alcohol, drugs or medications.

While setting up and using this product keep work area clean and well-lighted. Keep spectators and children out of the work area.

Use of the Flagpole Holder and the Umbrella Holder

Both products fit into a 2″ x 2″ Class IlI or Class IV hitch receiver. The hitch receiver must be properly installed by a qualified service technician
The Flagpole Holder is designed to hold a flagpole having a flagpole diameter of between 1-3/8″ to 2″. Note: If flagpole diameter is greater than 1-1/2″, a top and bottom bushing must be removed. The Flagpole Holder is designed to securely hold an average size flag (no larger than 5′ Width x 3′ Height, with a flagpole no longer than 6′). Over-sized flags should not be used with the Flagpole Holder. With a flag attached to the Flagpole Holder, the vehicle is not to be driven at high- way speed. When the flag is done being displayed, it hould be removed from the Flag Holder and the Flag Holder should be removed from the vehicle’s receiver hitch.
The Umbrella Holder is designed to hold an umbrella while the vehicle is parked. The vehicle should be located in a safe location, away from traffic and other disruptions. Never operate the vehicle with an open, or closed umbrella attached to the Umbrella Holder. When the umbrella is no longer being used, it should be removed from the Umbrella Holder and the Umbrella Holder should be removed from the vehicle’s receiver hitch.
Never modify these products and never attempt to use them for a purpose that they were not designed for.
Adhere to all Department of Transportation (D.O.T.) requirements. Adhere to all State Department of Motor Vehicle regulations when using these products.

Keep in mind that the warnings previously discussed cannot cover all possible conditions or situations that could occur. It is important that the person setting up and using both the Flagpole Holder and the Umbrella Holder understand that common sense and caution are factors which cannot be built into these products, and must be supplied by the person(s) using this product.

AVITEC is not responsible for the attachment or the installation of these products or the vehicle’s receiver hitch. The attachment of these products is critical and beyond the control of AVITEC. It neither guarantees, nor will it be liable for any damage resulting from the attachment or improper use of either the Flagpole Holder or the Umbrella Holder.

Limited Warranty

AVITEC warrants to the original retail purchaser that the product is free of defects in material and workmanship at the time of shipment. Each of these products are warrantied for 90 days from the date of purchase. This warranty is expressly in lieu of all other warranties, express or implied. Proof of purchase is required for warranty transactions; a copy of the original invoice or sales receipt is required.

Setting Up

Setting Up the Flagpole Holder

Refer to photo and illustration below and to the Assembly Diagram and Parts List at the end of this manual.
Always wear ANSI approved safety goggles when setting up this product, and when working with tools and equipment.
Make sure the vehicle’s engine is OFF with parking brake set, before attempting to set-up the Flagpole Holder. Make sure vehicle is in a safe, level location, away from vehicle traffic when setting up this product.
Slide end of tube into end of vehicle’s receiver hitch.
- Align the desired mounting hole of Flagpole Holder with hole in vehicle’s receiver hitch. Secure Flagpole Holder with Hitch Pin (A2) and fully engaged Clip (A1).
The Flagpole Holder includes a Top and Bottom Reducer Bushing (A4) designed for a flagpole with 1-1/2″ diameter, or smaller.
If the flagpole diameter is greater than 1-1/2″, both Top and Bottom Reducer Bushings will have to be removed. To remove bushings, unscrew each Knob Screw (A5), and remove Top and Bottom Reducer Bushings.
- Note: Not every diameter flagpole shaft will fit this Holder; additional adapters (not included) may be required. A qualified service technician can assist in making custom adapters from plastic tubing/piping, if needed.
Attach the Latch Pin (A6) to the bottom hole and lock the safety wire in place -see photo to left.
Place the flagpole into the vertical tube of the Flagpole Holder so that flagpole rests up against the Latch Pin.
Tighten the 2 Knob Screws (A5) to lock the flagpole in place. When in transit, stop frequently to check the condition of the flag; make sure it remains securely attached to the Flagpole Holder. When flag is in Flag- pole Holder, vehicle is not to be driven at hightway speed.

Setting Up the Umbrella Holder

Refer to photo and illustration on next page and to the Assembly Diagram and Parts List at the end of this manual.
Always wear ANSI approved safety goggles when setting up this product, and when working with tools and equipment.
Make sure the vehicle’s engine is OFF with parking brake set, before attempting to set-up the Umbrella Holder. Make sure vehicle is in a safe, level location, away from vehicle traffic when setting up this product.
Slide Umbrella Holder (A3) into Hitch Bar (A6), and secure with Screws/Washers (A8,A7). Slide other end of Hitch Bar (A6) into the vehicle’s receiver hitch. Align mounting hole of Hitch AWARNING Bar (A6) with hole in vehicle’s receiver hitch. Secure Hitch Bar with Hitch Pin (A2) and fully engaged Clip (A1). Pinch Point! Keep hands clear.
The Umbrella Holder includes a top and bottom Reducer Bushing (A4) designed for an umbrella shaft 1-1/2″ diameter, or smaller.
If umbrella shaft diameter is greater than 1-1/2″, both Reducer Bushings will have to be removed. To remove bushings, unscrew each Knob Screw (A5) until the Reducer Bushings can be removed. Note: Not every diameter umbrella shaft will fit this Holder; additional adapters (not included) may be required. A qualified ser- vice technician can assist in making custom adapters from plastic tubing/piping, if needed.
Place the shaft of the umbrella into the vertical tube of the Umbrella Holder. Note: the shaft of the umbrella must pass all the way through the tube to ensure proper engagement with the lower Knob Screw (A5).
Tighten both Knob Screws (A5) to lock the umbrella in place.
Always open and close the canopy of the Umbrella slowly, making sure that it does not interfere with people in the vicinity or the vehicle.
The Umbrella Holder is designed to hold an umbrella while the vehicle is parked. It is designed for stationary use only.

Maintaining the Flagpole Holder and the Umbrella Holder

To clean this product, wipe down with a damp cloth, then dry.
Frequently inspect the product for cracks or other damage. Make sure the Hitch Pin and Clip are in good condition. Check Screws for tightness.
If using the Flagpole Holder to display an American flag, make sure that the flag is in good condition with no rips or other signs of disrepair. A damaged American flag should be properly retired. See www.wikihow.com/ Disposal-of-a-damaged-American-flag.

Flagpole Holder|

1-3/8” to 2”

---|---
Umbrella Holder| For umbrella shaft diam- eter of 1-3/8” to 2”
For Use With| 2” x 2” Class III or Class IV hitch receiver
Hitch Pin| 5/8” Diameter

Flagpole Holder

Assembly Drawing and Parts List

NO / Parts List / QTY

A1 /Clip /1
A2 / 5/8” Hitch Pin /1
A3 / Flagpole Holder / 1
A4 / Reducer Bushing / 2
A5 / Knob Screw / 2
A6 /Latch Pin /1

Umbrella Holder

Assembly Drawing and Parts List

AVITEC-110450-Flagpole-Holder-fig11.

NO	Description	QTY.
A1	Clip	1
A2	5/8” Hitch Pin	1
A3	Umbrella Holder	1
A4	Reducer Bushing	2
A5	Knob Screw	2
A6	Hitch Tube	1
A7	Washer	4
A8	Bolt	4

Note: The Parts List and Assembly Diagram is provided as a reference tool only. Some parts are listed and shown for illustration purposes only, and are not available as replacement parts. All repairs to this tool (including replacing parts) should only be done by a qualified service technician.