FRIGIDAIRE FG7MQ Fully Modulating Variable Speed Condensing Upflow/Horizontal Gas Furances Owner’s Manual

: June 15, 2024
: Frigidaire

Table of Contents

FG7MQ Fully Modulating Variable Speed Condensing Upflow/Horizontal Gas
FEATURES and BENEFITS
DIMENSIONS
MODEL IDENTIFICATION CODE
LOCATION OF FURNACE COMPONENTS
SPECIFICATIONS
AIRFLOW DATA
MAXIMUM PIPE LENGTH CHART
ACCESSORIES
Documents / Resources

TECHNICAL SPECIFICATIONS
FG7MQ

FG7MQ Fully Modulating Variable Speed Condensing Upflow/Horizontal Gas

Furances

Fully Modulating, Variable Speed, Condensing Upﬂow/Horizontal Gas Furnaces
Induced Draft – 97.0 AFUE
Input 60,000 – 120,000 Btuh
The high efficiency upflow gas furnace may be installed free standing in a utility room, basement, or enclosed in an alcove or closet. Upflow/horizontal units come ready for upflow or horizontal application. The extended flush jacket provides a pleasing “appliance appearance.’ Design certified by CSA for application in Canada and the United States.

FEATURES and BENEFITS

i SEER: Energy efficient brushless DC (ECM) motor gives up to 1 SEER point efficiency gain in cooling.
Modulating heating operation Includes:
– Modulating gas valve from 100% to 50% input in 5% increments.
– Time proportioning modulation down to 15%.
– Variable speed inducer and
100% fired and tested: All units and each component are tested on the manufacturing line.
Best packaging in the industry: Unique corner post design assures product will arrive to the homeowner dent
30 second blower delay: At start-up assures a warm duct temperature at furnace start-up. Adjustable blower off settings (60, 90, 120 and 180 seconds).
30 second post purge: Increases life of heat
Hot surface igniter: Innovative application of a silicon ni- tride type Utilizes proven Smartlite® technology.
Color coded wire harness: Designed to fit the components, all with quick-connect fittings for ease of service and replacement.
Flexible category IV venting system: May be vertically or horizontally vented using either a one-pipe or two-pipe system for maximum flexibility in installation.
High Static Blowers: All models equipped with high static blowers.
Low Boy Height: Easy to apply in low ceiling applications, works well with taller high SEER coils, easier to handle and install.
Tubular primary heat exchanger: Heavy gauge aluminized steel heat exchanger and stainless steel secondary heat exchanger assures a long life.
90 second fixed cooling cycle blower-off delay (TDR): increases cooling performance when matched with a NORDYNE coil.
LP convertible: Simple burner orifice change for ease of convertibility.
Diagnostic lights for easy troubleshooting without counting flashess: Dedicated light for flame signal strength and 2 lights in combination to indicate all other fault codes with easy to recognize states without counting
Incorporates integrated control board : with connections for electronic air cleaner and humidifier.
Two piece door design: Enhances furnace appearance and uses captured screws to prevent losing door
Blower Compartment: Sealed door to reduce air leakage and insulated for ultra quiet operation.
Sealed Vestibule: Reduces burner and inducer sound
iQ Drive Thermostat: Provides modulation down to 15% and is required for furnace operation.

DIMENSIONS

*MQ Model #’s| Dimension “A”| Dimension “B”| Dimension “C”
---|---|---|---
060D-VB| 17 ½| 15 ⅞| 16 ⅛
080D-VC| 21| 19 ⅜| 19 ⅝
100D-VC
120D-VD|

24 ½

|

22 ⅞

| 23 ⅛

MODEL IDENTIFICATION CODE

LOCATION OF FURNACE COMPONENTS

*UPFLOW / HORIZONTAL FURNACE (MQ SERIES)**

SPECIFICATIONS

FG7MQ MODEL NUMBERS:| **-060D- VB| ****-080D- VC| ****-100D- VC| ****-120D- VD
---|---|---|---|---
Input – Btuh (a)| 60,000 / 30,000| 80,000 / 40,000| 100,000 / 50,000| 120,000 / 60,000
Heating Capacity – Btuh| 58,200 / 29,100| 77,600 / 38,800| 97,000 / 48,500| 116,400 / 58,200
AFUE**| 97.0| 97.2| 97.4| 97.0
Blower D x W| 11 x 8| 11 x 10| 11 x 10| 11 x 10
Motor H.P. – Speed – Type| 1/2 – Variable| 3/4 – Variable| 3/4 – Variable| 1 – Variable
Motor FLA| 6.2| 8.7| 8.7| 11.70
Rated Ext. SP – In. W.C.| 0.5| 0.5| 0.5| 0.5
Temperature Rise Range – ºF| 30-60| 35-65| 35-65| 40-70
Shipping Weights| 130lbs| 140lbs| 150lbs| 165lbs

NOTE: All models are 115V, 60 Hz. Gas Connections are 1/2″ N.P.T. AFUE = Annual Fuel Utilization Efficiency
(a) Ratings to 2,000 ft. Over 2,000 ft. reduce 4% for each 1,000 ft. above sea level.

iQ Controller Kit

Description	Sku
iQ Controller kit	920621*

Revision Letter

AIRFLOW DATA

Gas Input Rate (Btuh)| Target CFM for Selected Circulating Air Temperature Rises, F
---|---
45| 50| 55| 60| Constant
Full Input| Minimum Input| Full Input| Minimum Input| Full Input| Minimum Input| Full Input| Minimum Input
60,000| 1,110| 635| 1,000| 560| 940| 515| 850| 470| 950
80,000| 1,480| 850| 1,345| 740| 1,255| 685| 1,140| 625| 1,300
100,000| 1,850| 1,050| 1,680| 925| 1,565| 855| 1,460| 780| 1,760
120,000| 2,225| 1,270| 2,020| 1,115| 1,890| 1,025| 1,730| 940| 2,100

NOTE: This table lists the High and Low target CFMs for each maximum input rate and temperature rise. If the target CFM is more that 1,600 CFM, it is recommended that two return air openings into the furnace be used.
NOTE: The blower operating range is .1″ to .8″ ESP in wc.

MAXIMUM PIPE LENGTH CHART

FURNACE MODELS (BTU)| FURNACE INSTALLATION| SINGLE VENT PIPE LENGTH (FT.) with 1 long radius elbow| DUAL VENT PIPE LENGTH (ft.)
with 1 long radius elbow on each pipe
---|---|---|---
OUTLET 2” Diameter| OUTLET 3” Diameter| INLET/OUTLET 2” Diameter| INLET/OUTLET 3” Diameter
60,000| Upflow| 50| 80| 50| 80
Horizontal| 40| 80| 40| 80
80,000| Upflow| 60| 90| 60| 90
Horizontal| 50| 90| 50| 90
100,000| Upflow| 50| 90| 50| 90
Horizontal| 40| 90| 40| 90
120,000| Upflow| N/A| 90| N/A| 90
Horizontal| N/A| 70| N/A| 70

*NOTES:

Subtract 2.5 ft. for each additional 2 inch long radius elbow, 5 ft. for each additional 2 inch short radius elbow, 3.5 ft. for each additional 3 inch long radius elbow, and 7 ft. for each additional 3 inch short radius elbow.
Two 45° elbows are equivalent to one 90° elbow.
Subtract 5ft for each 2” tee and 8ft for each 3”
This table applies for elevations from sea level to 2,000 For higher elevations, decrease pipe lengths by 8% per 1,000 ft of altitude.
The minimum length for 2” or 3” diameter vent pipe is 5 ft.

ACCESSORIES

FG7MQ KITS

GENERAL TERMS OF LIMITED WARRANTY
Nortek Global HVAC LLC will furnish a replacement for any part of this product which fails in normal use and service within the terms and conditions of the warranty.
For complete details of the Limited Warranty, including applicable terms and conditions, see your local installer or contact the Nortek Global HVAC LLC warranty department for a copy.
Before purchasing this appliance, read important energy cost and efficiency information available from your retailer. Specifications and illustrations subject to change without notice and without incurring obligations.
Printed in U.S.A (0/2015)
212D-0914 (Replaces 212D-0112)
FRIGIDAIRE is a registered trademark of Electrolux Home Products Inc. and used under a license from Electrolux Home Products, Inc.
© Nortek Global HVAC, LLC. All Rights Reserved.

www.frigidairehvac.com

Documents / Resources

| FRIGIDAIRE FG7MQ Fully Modulating Variable Speed Condensing Upflow/Horizontal Gas Furances [pdf] Owner's Manual
FG7MQ 060D-VB, FG7MQ 080D-VC, FG7MQ 100D-VC, FG7MQ 120D-VD, FG7MQ Fully Modulating Variable Speed Condensing Upflow Horizontal Gas Furances, FG7MQ, Fully Modulating Variable Speed Condensing Upflow Horizontal Gas Furances, Modulating Variable Speed Condensing Upflow Horizontal Gas Furances, Variable Speed Condensing Upflow Horizontal Gas Furances, Condensing Upflow Horizontal Gas Furances, Upflow Horizontal Gas Furances, Horizontal Gas Furances, Gas Furances, Furances
---|---