KERBL Weldex II Welding and Barbecue Glove Instructions
- June 3, 2024
- KERBL
Table of Contents
Weldex II Welding and Barbecue Glove
Instructions
Weldex II Welding and Barbecue Glove
ref.no. | size |
---|---|
297370 | 10 / XL |
As the gloves are adjusted for special purposes, the lengths may deviate from
the requirements of EN ISO 21420:2020
388:2016+A1:2018
423X
Category II – Mechanical risks
402:2020
413X4X
Heat and fire
12477:2001 +A1:2005 -A &B
The EU-type examination was carried out by:
Instructions for use
Results of the EN ISO 21420:2020 mechanical test
Abrasion resistance: | 4 (min 0 / max 4) |
---|---|
Blade cut resistance (Coupe – Test): | 2 (min 0 / max 5) |
Tear resistance: | 3 (min 0 / max 4) |
Puncture resistance: | 4 (min 0 / max 4) |
Blade cut resistance (TDM): | X (min A/max F) |
Results of the EN 407:2020 thermal test
Burning behavior: | 4 (min 0 / max 4) |
---|---|
Contact heat: | 1 (min 0 / max 4) |
Convective heat: | 3 (min 0 / max 3) |
Radiant heat: | X (min 0 / max 4) |
Small molten metal splashes: | 4 (min 0 / max 4) |
Large molten metal splashes: | X (min 0 / max 4) |
The sign X, instead of a number, means that the glove is not designed for the
use covered by the corresponding test. Results only from samples of glove
palms with inserted lining. The overall classification of the glove does not
necessarily reflect the performance of the outermost layer.
Care and Cleaning: The service stages mentioned are based on tests that
were carried out exclusively on unused gloves. Transfer of the results on
gloves aftercare treatment is not possible. The manufacturer accepts no
liability for changes to the properties. For donning, check the integrity of
the glove and that the picked size fits the hand. For doffing, ease the glove
of one hand before removing the second glove to reduce the risk of
contamination.
Packaging and storage: This article is supplied in uniform sales
packaging made from recyclable cardboard. PE bags or similar environmentally
friendly coverings are the smallest packaging unit. The gloves must be stored
correctly, i.e. in boxes in dry rooms. The properties can be altered by
influences such as humidity, temperature, and light, as well as natural
alterations to the materials over a period of time.
Aging: It is not possible to give an expiry date, as this can be
dependent on the degree of wear, use, and the area in which the gloves are
used.
General information / Risk assessment: The glove types named here meet
the requirements of Regulation (EU) 2016/425 as brought into UK law and
amended, and are compliant with the above-mentioned harmonized/designated
standards EN ISO 21420:2020, EN 388:2016+A1:2018, EN 407:2020, EN
12477:2001+A1:2005. While selecting equipment, the user should perform risk
analysis based on the intended use and determine suitability based on the
product’s test standards and protection levels obtained. Laboratory tests
offer aid to the selection, however, they cannot take the actual workplace
conditions into account. It is therefore the responsibility of the user and
not the manufacturer to test the suitability of a certain glove for the
planned area of use. Gloves for general light handling in wet conditions. The
equipment provides protection against moderate mechanical risks. The maximum
wear time depends on the activity being carried out and the person. The glove
offers no protection against perforation with sharp objects, e.g. injection
needles. No gloves should be worn if there is a risk of becoming caught in
moving machine parts. The gloves contain no substances that are known to cause
harm to the wearer. The gloves lose their heat-insulating properties when wet.
For further information on the maximum permissible user exposure please
contact the manufacturer.
Further information and declaration of conformity by:
Albert Kerbl GmbH
Felizenzell 984428 Buchbach, Germany
www.keron-online.com
Kerbl UK Ltd Lands End Way
Oakham, Rutland LE15 6RF, UK
www.kerbl.co.ukSGS Fimko Ltd Takomotie
8 , FI-00380
Helsinki, Finland