Xiaomi MCC01M-1A Smart Cooking Robot User Manual
- June 1, 2024
- Xiaomi
Table of Contents
Xiaomi MCC01M-1A Smart Cooking Robot User Manual
Safety Precautions
Read this manual carefully before use, and retain it for future reference. To
ensure your safety and minimize the risk of personal injury or property
damage, please observe and obey the following safety precautions.
WARNINGS
- This product is for household use only.
- Appliances can be used by persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and if they understand the hazards involved.
- Please keep the product out of the reach of children. Children shall not play with or use this product.
- Do not place the product on unstable or wet surfaces. Keep the product preferably 30 cm or more away from fire or heat sources.
- The normal operating altitude range of this product is 0-2000 meters.
- Do not place the cooking base on heated or heatable surfaces including stoves, ceramic stoves, or induction stoves, nor near any high-temperature areas.
- Do not crush, strike, or scratch the product with anything sharp or heavy to prevent injuries or malfunction.
- The product cannot be used with an external timer or independent remote control.
- Do not modify, disassemble, or repair the product by yourself to avoid fire, electrical shock, and scalding.
- Stop using the product immediately if it malfunctions or breaks down to avoid fire, electric shock, and scalding.
- Ensure that the silicone parts of the product do not come into contact with solutions that contain more than 50% alcohol.
- Turn off the product and disconnect the power before replacing accessories or touching movable parts.
- Do not use accessories or parts that did not come with this product to avoid fire and personal injury.
- Steam and heat may damage, discolour or deform your furniture and walls, keep the product away from furniture and walls, preferably 30 cm and above.
- Use in a well-ventilated area to ensure that heat is properly dispersed.
- The blades inside the pot are sharp. Please be careful when emptying the pot and cleaning the blender assembly.
Precautions for Power Supply
- Do not use any power supply other than 220-240 V AC to avoid fire and electrical shock.
- Do not unplug by pulling on the power cord, to avoid electric shock or fire caused by short-circuiting.
- Do not allow children to use the product without an adult’s supervision. Keep it out of the reach of infants to prevent electric shock, burns, or other injuries.
- Do not plug or unplug the power cord with wet hands, to avoid electric shock or injuries.
- Use only power sockets rated at 10 A minimum.
- Unplug the power cord from the electrical outlet before performing any maintenance or moving the product.
- If the power cord is damaged or broken, it must be replaced or repaired by the manufacturer or the after-sales department to avoid safety hazards.
Precautions During Use
- Do not fill the pot above the maximum line (“2.2 L” mark).
- Do not remove the measuring cup during high-speed operation, to prevent grease or liquid spills.
- Do not attempt to force open the pot lid or locking mechanism.
- The pot lid can only be opened when the speed is at zero and the locking mechanism has been released.
- Do not use the whisk during prolonged cooking, such as slow cooking, slow simmering, or fermentation.
- Do not touch moving parts to prevent mechanical damage.
- Do not place your hands into the pot.
- Keep body and hair away from the blender assembly.
- Ensure that there is enough water in the pot when steaming.
- Please add water if the cooking time increases.
- Do not touch the measuring cup during or immediately after use.
- Keep away from children and infants and take special precautions to prevent them from being scalded.
- Do not move or shake the product during use.
- Do not place the scraper into the pot during cooking.
- Do not cover the top of the product during use, otherwise, the steam may be unable to escape.
- When adding water during blending, the water temperature should be less than 60°C to prevent burns and scalds if liquid overflows.
- The rotation speed will automatically decrease if the liquid temperature is too high during high-speed rotation.
- Note that pouring high-temperature liquid into the pot can cause the liquid to spray out due to vaporization.
- The pot must be used with the included cooking base.
Precautions After Use
- Promptly empty the ingredients in the pot after use. Remove the blender assembly and clean it promptly, being careful not to be scratched by the blades.
- Stop using the product immediately and unplug it from the power source if it malfunctions or breaks down.
- Thoroughly wipe the pot dry and clean before placing it onto the cooking base.
Precautions for Cleaning and Maintenance
- Do not immerse the product in water or splash it with water.
- Unplug the product before cleaning the cooking base.
- Do not use steel wool or other hard objects to clean the pot.
- Use only soft cloth for cleaning.
- Do not allow water or dirt to penetrate the casing of the cooking base.
- If the product will not be used for a long time, unplug the power cord and take measures to protect it from moisture, dust, and household pests.
Precautions for Malfunctions or Breakdowns
If any of the following conditions occur, immediately disconnect the product
from power and contact the after-sales service team for assistance.
- The power plug or power cord has become very hot during use.
- Smoke is arising from the cooking base or there is a burning smell.
- Some part of the product is cracked, loose or unstable.
- The pot deforms.
Product Overview
Smart Cooking Robot
Accessory List
Note : Illustrations of product, accessories, and user interface in the user manual are for reference purposes only. Actual products and functions may vary due to product enhancements.
Component Description
Component Functions
Component Instructions
Pot
The pot is used to process or heat ingredients. It consists of a stainless
steel bowl, a lid, and a blender assembly. Before cooking, it must be
correctly placed onto the cooking base. Please follow the steps below:
- Align the pot handle with the positioning point, then vertically place the pot onto the holder on the cooking base.
- Try to slightly rotate the pot to the left and right. If the pot cannot be rotated but can move slightly, then it has been placed correctly
CAUTIONS
- Place the product on a clean, sturdy, and stable counter surface in the kitchen.
- Keep the product away from the edge of the counter to prevent the product from falling due to movement during operation or being bumped.
- Do not place the product on heated or heatable surfaces including stove, ceramic stove, or induction stove, nor near high-temperature areas. Keep the product away from external heat sources.
- Do not place the product underneath furniture like shelves or cupboards, as this may cause the furniture to be damaged by steam generated during cooking.
Blender Assembly (Blender Blade + Blender Blade Base)
Remove the blender assembly before cleaning the blender assembly and the pot,
then install them back correctly after cleaning and drying for future use. The
blender blade is used for blending, cutting, and mixing food, therefore, it
must always be properly installed and fully locked with the blender blade
base; otherwise, an accidental injury may occur. Please follow the steps
below:
- To avoid the blender blade falling off accidentally, hold the handle of the pot with its mouth facing upwards.
- Rotate the blender blade base clockwise to remove it, and temporarily leave the blender blade in the pot.
- Carefully lift the handle of the blender blade to remove it from the pot, along with the rubber seal.
- When cleaning the blender blade, special care must be exercised to avoid being cut. Wipe dry after cleaning.
- Hold the handle of the blender blade along with the rubber seal, align the blender blade with the opening on the bottom of the pot, and put the blender blade into it till the rubber seal is in contact with the bottom of the pot.
- Install the blender blade base onto the bottom of the pot from below, then rotate it counterclockwise till the blender blade and the blender blade base are firmly locked together.
CAUTIONS
- The blades are extremely sharp. Take extra care when installing, disassembling, using, or cleaning them.
- Do not touch the blades. Doing so may result in injury.
- When disassembling the blender blade, ensure that the pot mouth is facing upwards. Otherwise, the blender blade may fall off and cause personal injury or deform the blades.
- Do not place your hands into the pot before removing it from the cooking base.
- To avoid burns by residual heat from cooking, make sure that the pot and the blender blade are cool enough to touch before removing them.
- Make sure that the blender blade is correctly installed. Check the blender blade and the rubber seal regularly.· When installing the blender blade, make sure that the blender blade and the rubber seal are t in place.
- Make sure that the rubber seal is intact. Otherwise, the product may be damaged because of the liquid leaking into the cooking base.
- Make sure that the blender blade is correctly installed and completely locked before cooking.
Pot Lid
The pot lid is used to seal the pot. To ensure safety during use, the cooking
robot can only be turned on when the lid is put in place and locked. Please
follow the steps below:
- With the lid handle to the right of the pot handle, then firmly place the lid on the pot and press it down with both hands. Then turn the lid clockwise until the lid handle is aligned with the pot handle. Make sure they are firmly locked together.
- Press the control knob to start cooking, and the pot will be automatically locked.
- The cooking robot will automatically detect whether the lid is in place or not. If not, the screen will display a prompt.
- The pot will be automatically unlocked once the cooking is completed.
CAUTIONS
- Do not force open the pot lid to avoid damaging the lock of the pot lid.
- Some hot steam may remain inside the pot after cooking is completed. To avoid burns and scalds by the steam, please exercise caution when opening the pot lid.
- Do not remove the measuring cup during cooking. In some recipes, the measuring cup will need to be removed to ensure the release of excess steam. Please refer to the specific recipe for details.
- Have a regular check to ensure that the rubber seal on the pot lid is not damaged.
- Do not remove the rubber seal when cleaning.
- For a better next-cooking experience, clean the pot promptly after use to prevent odours arising from food residue.
Steamer Set/Basket
The steamer set and basket are used for steaming food. The steamer set is
composed of a steamer lid, a steamer tray, a bottom insert, a steamer pot, and
a water collection tray. The steamer set is directly mounted onto the pot lid
so that steam can go through the open mouth in the pot lid during cooking to
steam the food. To use the steamer set, please follow the steps below:
- Place the steamer set onto the sunken part on the pot lid. Make sure they are aligned and locked firmly.
- To use the basket, place it into the pot with food ingredients in it to steam.
- You can use the different parts of the steamer set based on your needs.
- To collect condensed juices when steaming, place the water collection tray between the steamer pot and the pot lid. If the water collection tray is removed, the juices will flow into the pot.
CAUTIONS
- Food ingredients need to be distributed evenly inside the steamer pot, and the total weight of the ingredients to be cooked each time along with plates or dishes cannot exceed 2 kg.
- Be careful of steam burns when removing the steamer set or basket.
- Make sure there is enough water in the pot to prevent damage to the cooking robot caused by boiling dry.
- Promptly clean the steamer set and basket to avoid clogging the holes on the steamer set.
- The measuring cup needs to be removed when using the steamer set.
- Be mindful of the water amount in the water collection tray to avoid water overflowing. Normally, the water collection tray can collect condensed juices during steaming for about one hour.
Measuring Cup
The measuring cup can be used to block the open mouth in the pot lid to
prevent heat loss and ingredient splashing. It can also be used to measure
liquids. If only a small amount of liquid is needed, then the measuring cup
does not need to be removed. Slowly pour the liquid on the pot lid, and it
will flow into the pot through the gap between the measuring cup andthe pot
lid. To add more liquid or solid ingredients to the pot, follow the steps
below:
- Press the control knob to pause the current cooking task. Hold the measuring cup handle and pull it upwards to remove the measuring cup.
- Add the ingredients to the pot.
- Align the measuring cup with the open mouth in the pot lid and gently press down to reinstall the measuring cup onto the pot lid.
- Press the control knob to resume cooking.
CAUTIONS
- When removing the measuring cup during cooking, exercise caution to avoid burns from the hot steam that may remain inside the pot.
- In some recipes, the measuring cup will need to be removed to release excess steam. Please refer to the specific recipe for details.
Scraper/Measuring Spoon Set
The scraper can be used to remove cooked-on food and clean the pot. The
measuring spoons are used to measure small amounts of powder or liquid
ingredients. The spoons have different volume versions: 10 millilitres, 5,
millilitres, 2.5 millilitres, and 1.25 millilitres. Keep the following in mind
when using these accessories:
CAUTIONS
- None of the accessories can be used for other purposes.
- Do not place the scraper or measuring spoons inside the pot during cooking.
- Check accessories regularly, and replace them promptly if damage is found.
Whisk
In addition to whipping cream or egg whites, the whisk can also be used at low
speed to ensure an even mixing of the food, to prevent food from sticking or
burning onto the pot bottom. Follow the steps below for installation and
removal:
- Place the whisk onto the blender blade by inserting it into the gap of the cross-blade, and turn it slightly to fix it in place. Make sure that it cannot be easily removed.
- Hold the handle of the whisk and shake upwards to remove.
CAUTIONS
- Do not use a speed over Level 5.
- Do not use the scraper while using the whisk.
- It is forbidden to install or remove the whisk while the cooking robot is in use.
Blade Cover
The blade cover is used to enhance the convection of liquid in the pot and
protect softer ingredients from being cut up by the blade. It is suitable for
simmering and sous-vide cooking, and can also be used with the steam/boil mode
and the stew mode. When removing and installing the blender blade, the blade
cover will also protect your hand from being cut. Take the following steps to
install and remove the blade cover:
Installing: Align the center of the blade cover with the blade handle,
and press down the blade cover to make sure it is secured in place.
Removing: Hold the handle of the blade cover to remove it upward.
CAUTIONS
- Do not use at a speed over Level 1.
- Make sure the temperature does not exceed 100°C.
- Only use the blade cover when stewing or boiling with an adequate amount of liquid. Do not boil-dry the blade cover at high temperatures.
How to Use
Plug the power cord into a 220-240 V AC socket, connect the power, and turn on
the cooking robot, and then the boot animation will show on the screen. The
cooking robot’s screen will automatically go out by default if no operation is
performed in 10 minutes, and its auto-off time can be adjusted in the
settings. After the screen is off for 10 minutes, the cooking robot will enter
the energy-saving mode. Press and hold the control knob for 3 seconds or go to
the drop-down menu to turn off the cooking robot. To start the cooking robot,
press the control knob. If the cooking robot will not be used for an extended
period, press the power button to turn the cooking robot off.
Note: You can wake up the screen by tapping the screen or pressing the
control knob.
Connecting with Mi Home/ Xiaomi Home App
This product works with the Mi Home/Xiaomi Home app*. Use the Mi Home/Xiaomi Home app to control your device, and to interact with other smart home devices. Scan the QR code to download and install the app. You will be directed to the connection setup page if the app is installed already. Or search “Mi Home/Xiaomi Home” in the app store to download and install it. Open the Mi Home/Xiaomi Home app, tap”+” on the upper right, and then follow the prompts to add your device.
The app is referred to as Xiaomi Home app in Europe (except for Russia). The
name of the app displayed on your device should be taken as the default.
Note: The version of the app might have been updated, please follow the
instructions based on the current app version.
Wi-Fi Connection
When turning on the cooking robot the first time, please follow the
instructions on the screen to connect to Wi-Fi.
Initial Setup
Follow the on-screen instructions to complete the initial setup when the
cooking robot is turned for the first time. Press the control knob or swipe
the screen to the left to proceed to the next step during operation. Press the
control knob again to enter the home screen after completing the setup.
Settings can be changed at any time in Profile > Settings.
Usage Settings
Setting values: The cooking parameters such as time, temperature, and speed
can be set before and during cooking. The cooking robot can only work if both
time and speed are set. Tap the time, temperature, and speed icons on the
screen to set values, and turn the control knob to change the values. Press
the control knob to start cooking once the value settings are completed.
Selecting recipes: Choose the Recipes on the screen or tap the icon on
the top right corner to search the recipes. Follow the step-by-step recipe to
operate the cooking robot for cooking.
Setting time
- Tap the time setting icon to enable the time setting.
- Rotate the control knob to set the cooking time.
CAUTIONS
- The preset time can be changed at any time during cooking (except for certain modes). Tap the time setting icon and turn the control knob to select desired cooking time. The cooking robot will resume cooking as per the latest set time till the cooking is complete.
- Before the preset time ends, press the control knob to pause the cooking robot and add ingredients during cooking. Press the control knob again to start the cooking robot and resume cooking as per the original preset time.
- To end cooking before the preset time, tap the time setting icon and turn the control knob to 00:00:00.
Setting temperature
- Tap the temperature setting icon to enable the temperature setting.
- Rotate the control knob to set the temperature.
CAUTIONS
- The cooking temperature can be changed at any time during cooking (except for certain modes).
- If there is no need to heat, set the temperature to “__”
Setting speed
- Tap the speed setting icon to enable the speed setting.
- Rotate the control knob to set the rotation speed.
CAUTIONS
- The speed can be changed at any time during cooking (except for certain modes).
- The cooking robot can start cooking after the time and speed are set.
- There are 20 speed levels for both forward and reverse rotation. Turn the control knob clockwise to adjust the forward speed, and counterclockwise to adjust the reverse speed. The higher the level, the faster the speed.
- Do not use high speeds when cooking hot food or soup over 60°C,ttont the food from overflowing and causing burns.
- By rotating the control knob clockwise or counterclockwise, you can change the rotation direction of the blender blade. To gently stir and mix the food, use the reverse rotation.
Preset modes
The cooking robot has multiple preset modes to meet various cooking needs. You
can go to the home screen to select the presting including we thine, trimming
station, Singhh reading me saint, line stringing wincing, chopping,
Mincing
- Clean the ingredients and cut them into small pieces, then put them into the pot. Make sure that the amount of the ingredients does not exceed the pot maximum level.
- Correctly install the pot onto the cooking base, then put on the pot lid. Make sure that the lid is installed correctly and locked onto the pot.
- Turthepres-cocaine abodalmatiann stop upon completion and processPetal control ok to pause illanyy used.
- Remove the pot from the cooking base once ingredient processing is completed, and use the scraper to take out the food.
CAUTIONS
- The cooking robot will shake slightly during operation, please do not leave the cooking robot unattended.
- Turn off the cooking robot if it vibrates excessively or ingredients stick to the sides of the pot. Use the scraper to spread the ingredients evenly across the bottom of the pot and then turn the cooking robot back on.
Weighing
- Install the pot onto the cooking base and select weighing mode on the mode screen.
- Place the ingredients to be weighed into the pot, and the screen will then display the weight of the ingredients.
- Press and rotate the control knob to zero, and then add the next ingredient to the pot. The weighing process can be repeated till an accumulated maximum weight of 5000 g is reached.
CAUTIONS
- The weighing mode can only be used when no other modes are running.
- When using the weighing mode, please make sure that the cooking robot is on a level surface. Otherwise, the weighing results are running on a level surface. Otherwise, the weighing results may be inaccurate.
- Tap”~” in the top left corner of the weighing screen to exit weighing mode.
Mode Functions
Note: On-screen mode names may vary due to product enhancements, please refer to the actual product.
Mode Examples
Note: On-screen mode names may vary due to product enhancements, please refer to the actual product
Recipe Function
For a better smart cooking experience, kindly connect the product to a network
before use. Tap Recipes in the top left corner of the screen to access
personal recipes; tap the search bar (the magnifying glass icon) in the top
right corner of the screen to search for recipes by entering keywords.
Care & Maintenance
- Before the first use, thoroughly clean all components and accessories except for the cooking base.
- Thoroughly clean and dry all used accessories after each use.
- Use the clean mode between cooking steps or dishes to clean the residual food in the pot. You can find the mode on the mode screen.
- Do not use sharp objects or metal wool to clean the pot, instead, use stainless steel cleaner.
- Use a soft cloth to clean the surface of the plastic accessory such as the steamer set.
- Disconnect the power source before cleaning the cooking base.
- Wipe down the cooking base using a slightly damp cloth and mild detergent.
- Be careful not to use too much water when cleaning the cooking base to prevent air and water from entering it.
- The pot and the blender assembly maybe damaged if they come into contact with water, other liquids, or food residue over a long period. Promptly clean the components after each use.
- Prolonged stewing or contact with acidic substances may cause rusting, please pay attention to the ingredients used.
- Regularly check the cooking base and accessories including the pot, power cord, rubber seals on the pot lid, and blender assembly for damage.
- To avoid product damage, regularly check the product’s ventilation ports to make sure there is no blockage.
- Unplug the product when it is not in use.
- There is a drain structure inside the holder of the pot on the cooking base. If a large amount of broth or liquid is accidentally spilled onto the holder, do not turn over the cooking base, as the liquid will automatically flow into the bottom drain hole.
- Use an absorbent sponge or soft cloth to wipe off the liquid that remained on the cooking base surface.
- The product should be kept dry and clean, and placed in a dry, well-ventilated environment.
- Do not use damaged accessories.
- The blender assembly and accessories are consumables. For best cooking results, replace them promptly based on their condition and the frequency of use.
Specifications
Name | Smart Cooking Robot | Model | MCC01M-1A |
---|---|---|---|
Total Rated Power | 1700 W | Rated Voltage | 220–240 V~ |
Motor Rated Power | 500 W | Heat Rated Power | 1200 W |
Capacity | 2.2 L | Rated Frequency | 50–60 Hz |
Net Weight | 10 kg | Heating Method | Induction heating |
Gross Weight | 13.8 kg | Item Dimensions | 413 × 316 × 344 mm |
Wireless Specifications
The WLAN function for this device is restricted to indoor use only when
operating in the 5150 to 5350 MHz frequency range. Hereby, Chunmi Technology
(Shanghai) Co., Ltd. declares that the radio equipment type MCC01M-1A complies
with Directive 2014/53/EU. The full text of the EU Declaration of Conformity
is available at the following internet address:
http://www.mi.com/global/service/support/declaration.html.
For detailed e-manual, please go to
www.mi.com/global/service/userguid
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as the terms and conditions of such collection points.
Troubleshooting
Fault Codes
If the cooking robot is not working properly, the screen will show an error
code. Please refer to the table below and the corresponding solutions.
User Manual Version: V1.0
For further information, please go to www.mi.com
Manufactured for: Xiaomi Communications Co., Ltd.
Manufactured by: Chunmi Technology (Shanghai) Co., Ltd.
(a Mi Ecosystem company) | Address: Building 11, 1333 Jiangnan Avenue,
Changxing Science and Technology Park, Lingang, Shanghai, P.R. China
Download PDF:Xiaomi MCC01M-1A Smart Cooking Robot User Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>