Xiaomi 3 Smart Doorbell User Manual

Xiaomi 3 Smart Doorbell User Manual

Function Introduction

Image quality is further upgraded with 2K resolution for higher quality image capture, not only ensuring good viewing results but also clearer and more detailed recording of doorstep activity.The built-in 5200mAh high-capacity lithium battery further improves battery life, so there is no need for frequent charging and battery replacement. The USB Type-C charging port enables faster and easier charging.With the diagonal 180° equipped with a human body sensor and AI human shape recognition technology, Xiaomi Smart Doorbell 3 monitors abnormal movements of your doorway and sends notifications to your smartphone once they are detected.

Smart doorbell x 1. Chime x 1. Type-C charging cable x 1. Mounting base x 1. Removal pin x 1. User manual x 1. Screws x 1. Attention sticker x 1Warranty notice x 1

The built-in 5200mAh high-capacity lithium battery further improves battery life, so there is no need for frequent charging and battery replacement. The USB Type-C charging port enables faster and easier charging. Only needs charging 3 times a year.

Xiaomi Smart Doorbell 3 has two installation methods.Double-sided tape installation: suitable for smooth wood, metal, and smooth ceramic tile surfaces, please clean the surface before installation; tear off the double- sided adhesive release paper from the installation base, and stick the backboard at the selected position.Expansion screw installation: Drill holes with an electric drill and install expansion screws on the wall on one side of the door lock, suitable for cement and grey walls.

After selecting a suitable position, after the mounting base is pre-placed in the selected position, use a pencil to mark the punching position according to the 4 openings Punch holes, the hole diameter is 6mm, and the hole depth is about 30mm (matching KA3×20, 3mm countersunk head self-tapping screws and matching expansion pipes) Nail the 4 expansion tubes into the drilled holesThe arrow direction of the installation base is upward, and the 4 holes are aligned with the holes on the wall. Put the screws through the holes of the installation base and use a Phillips screwdriver. screwed into the expansion nut on the wall after the bottom of the doorbell installation is fixed, the doorbell is buckled on the base and the installation is completed. Note The installation wall needs to be able to withstand at least 10 times the total weight of the doorbell To prevent injury, the device must be firmly fixed on the wall as specified in the installation instructions.The doorbell does not have door-to-door installation service. Careful operation is required during installation and removal to avoid damage to the wall.

Installation height: After the APP is added and paired, enter the real-time screen before installation, and select the installation height and location according to the screen displayed on the phone. After a good position, tear off the 3M adhesive release paper and mount it. Recommended installation height: The camera is 1.4-1.6 meters away from the ground, please choose the installation height and location according to the height of you and your family; Please find a suitable installation height according to the height of most members of the family.

Not supported.

Xiaomi Smart Doorbell 3 has a two-colour button light. When you get the doorbell for the first time reset it and wait for the connection to the network, the indicator light will flash orange The orange light is always on when the binding and distribution network fails, and you need to reconnect at this time After the doorbell is successfully paired, the white light of the indicator light will be on, and the white light will be off after entering the sleep mode In the charging state, the white light is in a breathing state; when fully charged, the white light is always on When the charging state is abnormal, the white light is flashing When someone passes in front of the door, triggers the doorbell to shoot or presses the doorbell, the white indicator light stays on until the shooting ends.

Not supported.

If you need to change the network connected to the doorbell or the Mi Home APP account, use the card pin to open the back panel of the doorbell, press and hold the RESET button on the back of the doorbell, and hear the prompt tone “reset successful, beep the doorbell is reset successfully.

Support. Xiaomi Smart Doorbell 3 can automatically switch to night vision mode according to the degree of change in surrounding light. Infrared lights are 940nm light waves, invisible to the naked eye. When the infrared light is on, it can be viewed through the phone camera, which is normal.

Not supported.

The SN number can be viewed from the product packaging and the label on the back of the doorbell (the receiver is an accessory, the receiver SN is the factory serial number, and it is normal to be inconsistent with the doorbell SN). Product packaging There will be an SN barcode label on the back of the product box, you can check the SN number here.

Xiaomi Smart Doorbell 3 adopts a diagonal 180° large viewing angle lens, with a 3 million high-definition pixel sensor, the picture is real and clearF2.0 large aperture lens, which greatly increases the amount of light entering, and can capture the details of the picture even in weak light.

The infrared detection angle of Xiaomi Smart Doorbell 3 is 100° (the angle that can be detected by motion detection).

How to adjust the volume of Xiaomi Smart Doorbell 3 receiver?

Short press the pairing button, the volume can be adjusted cyclically.

Mi Home APP doorbell settings (3 dots icon in the upper right corner) doorbell settings automatic reply voice Add voice recording completed name recording OK.Support adding 2 automatic reply voices. The length of the recorded voice is up to 10 seconds.After the setting is completed, it is only set in the APP. After you need to trigger the doorbell (press the doorbell or move the trigger), the doorbell will go online again to take effect.

How to check the running status of Xiaomi Smart Doorbell 3?

Mi Home APP doorbell settings (3 dots icon in the upper right corner) doorbell settings device information The device status information is as follows Doorbell firmware version: the current firmware version of the doorbell The number of days used: the number of days the doorbell has been used since the last charge of the doorbell Power-on time: The accumulated power-on time of the doorbell since the last charge (the length of video recording and uploading) Power-on times: the number of times the doorbell has been turned on since the last charge of the doorbell (including the number of times when no humanoid was detected when the doorbell was turned on – no video upload) Number of videos shot: The number of videos shot by the doorbell since the last charge of the doorbell (the doorbell is displaced, and the humanoid is not detected, and the minimum 5-second video is shot) Wi-Fi name: the name of the WiFi the doorbell is connected to. Wi-Fi strength: The WiFi signal strength of the doorbell when it was connected to the Internet recently (if it is lower than 40%, it is recommended to adjust the routing position or install a WiFi signal amplifier to try to improve the WiFi signal strength of the doorbell installation location) IP address: the IP address assigned to the doorbell by the route MAC Address: Doorbell MAC address.

How to download the video recorded by the doorbell on Xiaomi Smart Doorbell 3?

Mi Home APP–doorbell–settings (3 dots icon in the upper right corner)–storage management–local–download list–download the desired video. Downloaded videos can be downloaded in batches up to a maximum of 50. The storage location is the local album. (Same for iOS and Android)

Mi Home APP—doorbell—three dots in the upper right corner—face recognition—face management—mark the face that needs to be marked.

Mi Home APP–Settings (3 dots icon in the upper right corner)–Device Sharing–Click Edit in the upper-right corner–Select to delete the shared device.

Mi Home APP—doorbell—three dots in the upper right corner—face recognition—face management faces that have not been annotated cannot be deleted, and faces that have been annotated will be released and saved in the unannotated faces after they are deleted. 10 faces can be set. Xiaomi Smart Doorbell 3 comes with one month of face recognition.

Trigger conditions: Someone rings the doorbell, the doorbell is removed, the battery is exhausted Execution condition: The doorbell has no execution condition

Not supported.

Troubleshooting

What should I do if the Xiaomi Smart Doorbell 3 has noise when viewing the live image?

Check whether the doorbell microphone hole is covered or there is foreign matter If there is noise in the real-time video, please keep the phone away from the doorbell (to avoid howling), and avoid installing the doorbell next to the electronic door lock Wait next to electronic equipment.

Check whether the sound on the phone is too low to cause silence Check whether the Mi Home APP has obtained permission to use the phone’s microphone (recording), if not, please enable the relevant permission in the phone settings.

Check whether the sound on the phone is too low to cause silence. Check whether the Mi Home APP has obtained permission to use the phone’s microphone (recording), if not, please enable the relevant permission in the phone settings.

When making a call, please try not to place the phone and the device in the same space, and keep the device more than 10 meters away. Call).

Xiaomi Smart Doorbell 3 is a 3-megapixel high-definition video recording, which requires high decoding requirements for phones. Due to the limited CPU computing power of iPhone6/6S series models (or older phones), it will cause freezes when watching high-definition videos. , it is recommended to switch to smooth mode to watch.

The principle of power display in Xiaomi Smart Doorbell 3 APP The doorbell is displayed in the APP by converting the battery voltage into the number of battery cells or a percentage.The power display is not real-time, the doorbell needs to be online, the data is transmitted to the cloud, and the cloud is fed back to the mobile APP for display.If the network is abnormal and the power consumption is abnormal in a short period APP cannot accurately obtain the synchronization data of the doorbell After the charging is completed, you can press the doorbell several times. After the doorbell is connected to the Internet and transmits the battery information to the cloud, refresh the Mi Home APP, and the APP can quickly display the battery level of the doorbell.

Xiaomi Smart Doorbell 3s voice cannot prompt for wrong password.

Why do I add (bind) a doorbell to the Mi Home APP, and the doorbell prompts that it is paired by another account?

The cause the doorbell can only be paired by one Xiaomi account, and after binding, it can be added (paired) to other accounts, and it cannot be added successfully Popularization of knowledge Mi Home APP has several login methods The phone number has passed the verification code Xiaomi account through password, email through password If the user’s account is not paired to a phone number, each login method may generate an associated Xiaomi account (You can also manually associate the relevant login methods after logging in) — Whether to bind the association can be found in the Mi Home APP–Profile–avatar (left Upper corner)–personal information–account binding & confidential information view If the user uses any of the above login methods to log in to bind the doorbell, and then changes other login methods, the new account will If there is no doorbell, other accounts cannot bind the doorbell until the original account is unpaired (delete the doorbell in the APP). Method of exclusion Confirm whether the paired phone number is the main paired phone number. If it is the main paired phone number, please try to use the phone number and Xiaomi account. Log in to the Mi Home App to check which account is paired, and unbind (long press the doorbell icon in the APP and click the pop- up delete button) after the device can be paired to another account, and the non-primary paired phone cannot be unpaired Make sure that the above 2 ways to log in to Mi Home do not have a device, and the customer service determines whether it can be unpaired

After the receiver is powered on, it will ring the default bell once by default. If it does not ring, check whether the power supply of the socket is normal; if the power supply is normal, the receiver is abnormal Press and hold the receiver pairing button for 3 seconds according to the prompt, and he receiver will make a “beep” sound, and the doorbell will enter the pairing mode. The pairing mode lasts for 2 minutes, and the receiver exits the pairing mode after two beeps. The network connected to the doorbell should be normal when pairing The best distance for pairing is 2 meters from the doorbell and the receiver (do not install the doorbell on the door for pairing)

Check whether the doorbell and the receiver are powered on normally and the pairing is successful. If the power is on and the pairing is successful, please bring the receiver close to the doorbell and try again. The doorbell and the receiver are connected by RF 433MHz radio frequency, and the transmission distance is affected by the obstacles between the two. 433MHz is the public frequency band (the car remote control key uses this frequency band). If the interference of the adjacent frequency band in the use environment is large, the transmission distance and the use effect will be reduced.

What should I do if the Xiaomi Smart Doorbell 3 consumes abnormally?

Reasons affecting power consumption If the signal strength of the WiFi connected to the doorbell is high, the video recorded by the doorbell will be uploaded soon; if the signal strength is low, the upload time of the recorded video will be longer. The signal strength is low, the transmission power of the doorbell is high, the power consumption is high, and the power consumption is high) Temperature: the battery capacity will drop significantly when the temperature is lower than 0 degrees Boot time The time of the video shot and uploaded by the doorbell the time of the user’s real-time video (live monitoring) the shooting interval the length of stay Note Even if the doorbell is not paired in the Mi Home APP, when the ordinary doorbell is used, the motion detection is turned on by default. After someone triggers the doorbell (someone rings the doorbell or detects someone moving), the doorbell will try to connect to the Internet and shoot video, but the doorbell cannot connect to wifi successfully, and cannot upload videos to the cloud. In the most power- saving mode, you need to turn off the motion detection function in the APP. After it takes effect, you can only take photos or videos when you ring the doorbell.

What should I do if Xiaomi Smart Doorbell 3 cannot be charged?

When the doorbell 3 is charging, the button light will be in the state of white breathing light, and it will light up in white when fully charged. If the button light still does not turn on after being plugged in and charged for some time, please try to press the power button or rethe set button for a long time.

The battery report can only be done when the doorbell is online (press the doorbell button or detect a human body). Please click the doorbell after charging is complete. (physical) button, and then check the power display on the Mi Home app, so you need to refresh the APP (or log out and log in again).

Why is the data in the device information not updated after the Xiaomi Smart Doorbell 3 is fully charged in the Mi Home APP (the doorbell charging indicator (button light) shows a solid white light)?

The information in the device will not be recalculated until the battery power is below 10 and charged to more than 50.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>