NEXX X.WED3 Adventure Helmet Instruction Manual

X.WED3

X.WED3 Adventure Helmet

At NEXX, we do not just engineer helmets, we tech emotions.
We believe in the heat of passion – parts of life getting new blood.

HELMETS FOR LIFE is our motto, beyond the protection, past excellence, that any motorcyclist regardless of age or style lives the moment they wear NEXX.

Please read this manual very carefully before wearing your helmet and keep it in a safe place. For a correct use and for your safety, please pay attention to following instructions. The main function of the helmet is to protect your head in case of impact. This  helmet is made to absorb some of the energy of a blow by partial destruction of its component parts and, even though damage may not be apparent, any helmet which has suffered an impact in an accident or received a similarly severe blow or other abuse should  be replaced. To maintain the full efficiency of this helmet, there must be no alteration to the structure of the helmet or it´s component parts.

X.WED 3 DUAL SPORT

PARTS DESCRIPTION

1 – Shell
2 – Visor / Shield
3 – Top Center Air Intake ventilation
4 – Top side Air Intake ventilation
5 – Peak
6 – Chin Air Intake Ventilation
7 – Frontal Air Intake Ventilation| 8 – Spoiler
9 – Sunvisor Button
10 – X.COM 3 cover
11- FRS – Fast Release System Button
12 – Visor Mechanism
13 – Gog gle Strap Holder
---|---

CARBON VERSION EXCLUSIVES

VENTILATIONS

HOW TO ADJUST THE PEAK

1. HOW TO ADJUST THE PEAK

2. CHOOSE ONE OF THE THREE POSITIONS AND MOVE THE PEAK

3. TIGHTEN THE SCREW TO THE CHOSEN POSITION

HOW TO PLACE THE PEAK EXTENSOR

1. REMOVE THE COVERS, BOTH SIDES

2. PLACE THE EXTENSOR AND SLIDE

3. FIX THE EXTENSOR AT THE HOLDER HOLE BOTH SIDES

HOW TO ADJUST THE PEAK EXTENSOR

1. EXTENSOR HOLDER WITH 3 POSITIONS

2. ADJUST THE PEAK TO YOUR FAVORITE POSITION

HOW TO REMOVE THE PEAK

1. UNSCREW THE PEAK HOLDERS

2. REMOVE THE SCREW

3. REMOVE THE SCREWS BOTH SIDES

4. REMOVE THE PEAK

HOW TO CHANGE HELMET TO STREET MODE

1. REMOVE THE PEAK (SEE DETAILS PREVIOUS PAGE)

2. INSERT THE “STREET COVERS” IN THE HOLES
   

HOW TO CHANGE HELMET TO OFF ROAD MODE

HOW TO REMOVE THE VISOR MECHANISM COVER

HOW TO CLEAN THE VISOR

To clean the visor without affecting its characteristics should be used only soapy water (preferably distilled) and a soft cloth. If the helmet is deeply dirty (ex.Insect remains) can add a little liquid from the dish to water.
Remove the visor from the helmet before carrying a deeper cleaning. Never use objects to clean the helmet that may damage/scratch the visor. Always store the helmet in a dry place and protected from light, preferably in the bag provided by NEXX HELMETS.

HOW TO REMOVE THE VISOR

HOW TO PLACE THE VISOR

HOW TO USE THE INNER SUN VISOR

HOW TO REMOVE DE INNER SUN VISOR

HOW TO PLACE THE INNER SUN VISOR

PINLOCK *

1. Remove the helmet shield
2. Bend the helmet shield and place the Pinlock® lens between the two pins provided in the helmet shield, fitting exactly into the dedicated recess.
3. The silicon seal on the Pinlock® lens must make full contact with the helmet shield in order to avoid any condensation forming between the helmet shield and the Pinlock® lens.
4. Remove the film

ERGO PADDING *

The helmet size adjustment system using interior foams that allow a better filling according to the shape of the head;

• Not included

HOW TO PLACE ACTION CAMERA SIDE SUPPORT

HOW TO PLACE THE CHIN ACTION CAMERA SUPPORT

HOW TO PLACE THE TOP ACTION CAMERA SUPPORT

1. UNSCREW TOP PEAK HOLDER

2. PLACE SUPPORT ON TOP OF THE PEAK

3. SCREW TOP PEAK HOLDER WTH THE BIGGER SCREW

4. CAN ALSO BE USED WITHOUT THE PEAK

LINING SPECIFICATIONS

The lining of the helmet has the following characteristics:

• Removable,
• Anti-allergy
• Anti-sweat

This lining can be removed and washable, as shown in the picture.
If for some reason this lining is damage it can be easily replaced.

REMOVABLE LINER PARTS

FRS – FAST RELEASE SYSTEM

REMOVE THE EARPADS FOR CLEANING PURPOSES

REMOVE THE EARPADS IN CASE OF EMERGENCY

REMOVE THE EARPADS IN CASE OF EMERGENCY

HOW TO REMOVE THE INNER LINING

1. PULL THE EARPADS BOTH SIDES USING FRS SYSTEM (SEE PREVIOUS PAGE)

2. PULL THE BACK SIDE OF THE LINNER

3. RELEASE THE SPRINGS

4. PULL THE FRONTAL PART OF THE LINNER

HOW TO PLACE THE INNER LINING

1. INSERT THE FRONT OF THE LINNER

2. TIGHTEN THE SPRINGS

3. INSERT ON THE BACK

4. MAKE THE STRAP PASS THROUGH THE EARPADS

5. SLIDE THE RED BUTTON TO LOOSE THE EARPADS (SEE FRS PAG.31)

6. INSERT (SEE DETAILS PAGE 37)

7. INSERT (SEE DETAILS PAGE 37)

8. PRESS AND SLIDE FRS BUTTON UNTIL CLOSE POSITION

9. PRESS THE PIN

10. PRESS THE PIN

11. PRESS THE PIN

12. MAKE SURE THE BUTTON IS SECURELY LOCKED AND THE EARPADS SECURELY ATTACHED

HOW TO PLACE THE INNER LINING

HOW TO PLACE THE HIDRATATION TUBE

*Available in some models

HOW TO CHANGE DUST FILTER FOR WINTER FILTER

1. REMOVE THE CHIN FILTER HOLDER AND THE DUST FILTER

2. INSERT THE WINTER FILTER AND W THE CHIN FILTER HOLDER

HOW TO REMOVE GOGLE STRAP HOLDER

ACCESSORIES

*Available in some models

SIZE CHART

XS
S| CM
51/52
53/54
55/56| IN20,1/20,5
20,9/21,3
21,7/22
| M
L| 57/58
59/60| 22,4/22,8
23,2/23,6
| XL
XXL
XXXL| 61/62
63/64
65/66| 24/24,4
24,8/25,2
25,6/26

Wrap the flexible measuring tape around your head.

The size selection of the helmet is crucial to ensure the safety of the user. Never should use a helmet that is too small or too large in relation to the size of the head. To purchase a helmet is important that you try it: make sure the helmet fits perfectly to the head,  there should be no gap between the helmet and the head; make some movements of rotation (left and right ) with the helmet on the head(closed) this should not shake; it´s important that the helmet is comfortable and involving the entire head.

X.COM 3 *

The X.WED 3 model is by Default Equipped to Accommodate the NEXX Helmets X-COM 3 Communications System.

HOMOLOGATION TAG

HELMET CARE

• Light colors with matte finish require extra care as they are naturally more exposed to dust, fumes, compounds or other types of impurities.
  THIS IS NOT COVERED UNDER WARRANTY!
  Neon colors will fade when subjected to prolonged UV rays exposure.
  THIS IS NOT COVERED UNDER WARRANTY!
  We are not liable for any damage, loss or detriment resulting from faulty assembly of any accessory.

• Do not expose the helmet to any type of liquid solvent;

• The helmet should be handled with care. Leaving it drops can damage the painting as well as reduce their characteristics of protection.
  THIS NOT COVERED UNDER WARRANTY!

• Keep the helmet in a safe place (not hang on the mirror of motorcycle or other support than can damage the lining). Do not carry your helmet on the biker or in the arm while driving.

• Always use the helmet in the proper position, using the buckle to adjust to the head;

• In order to maintain trouble free operation of the visor, it is advisable to periodically lubricate the mechanisms and rubber parts around the visor with silicone oil. The application may be made with a brush or with the help of a cotton swab.
  Apply sparingly and remove the excess with a dry clean cloth. This proper care will maintain the softness of the rubber seal and will dramatically increase the durability of the visor fixing mechanism.

• Clean and lubricate mechanisms after use in extreme off road dust and dirt conditions.

This hight quality helmet is made with the most advanced European technology. The helmets are technologically advanced for the motorcycle rider´s protections, which are made for motorcycle riding only.
This helmet specifications is subject to change without notice.

HELMETS FOR LIFE

Nexxpro Fábrica de Capacetes S. A.
Zona insdustrial de Amoreira da Gândara, lote nº11
3780-024 Amoreira da Gândara,
Anadia – PORTUGAL
[email protected]
www.nexx-helmets.com

MADE IN

MARÇO 2023/R01

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>