scott aerator 13245 Color Changing LED Fountain Light Sets Instruction Manual
- June 1, 2024
- scott aerator
Table of Contents
scott aerator 13245 Color Changing LED Fountain Light Sets
This Kit Includes
- (2-4) LIGHTS WITH POWER CABLE
- (2-4) 1/2″ BOLTS AND NUTS
- (2-4) STAINLESS STEEL ARMS
TRANSFORMER CONTROL UNIT:
- TIMER
- LED CONTROL BOX
REMOTE CONTROL
Tools Needed
SMALL FLAT HEAD SCREWDRIVER PHILLIPS HEAD SCREWDRIVER 7/16″ AND 1/2″ WRENCHES
AND PLIERSc
WARNING: Bypassing the transformer will cause the fixtures to fail. The transformer is an integral and required part of the system.
Assembly Instructions
- Attach each arm assembly to the water feature. Be sure to orient the arms with “L” facing upward. Remove one of the 2″ bolts attaching the float to your Scott water feature and align the holes with the stainless steel arm. Reinsert the bolt with washer, outward through the housing, float and stainless steel arm. Secure with a washer and nut. Repeat for each arm assembly.
- Continue by attaching each light to the slotted end of the stainless steel arms. Feed 1/2″ x 1/4″ bolt downward through each light bracket and steel arm then secure with 1/4″ nut. The lights can be positioned along the arm by loosening the lock nut, sliding the light to the desired position, and then re-tightening the nut.
- Prepare the transformer control unit for mounting by attaching the 4 mounting brackets to the back of the box using the included screws.
- Securely mount the transformer control unit to your wall or post with the four mounting brackets.
Remote Instructions
- If you sync (reconnect) the remote and the lights are on the bright white (W) mode, double-click the “W” button to toggle back to the standard mode/hues.
- The “W” button toggles the colour wheel (and the “modes”) from a standard hue to a bright white shade of the current colour. Click the “W” button once to enter/exit that mode.
- Touching anywhere on the colour wheel will exit out of whatever “mode” you might be on. Pressing the “MODE +” or “MODE -” buttons will then start you at mode #1.
- You can navigate the “modes” from #1 to #10 sequentially, but you cannot skip numbers or go directly from mode #10 to mode #1 (or vice versa). You have to click the “MODE -” button until you reach mode #1.
- Each mode can be individually customized with preferred speed and brightness.
Timer Programming Instructions
- Set the current time by rotating the dial until the time lines up with the TIME NOW arrow.
- Pull all of the segment pins into the up position then push down the pins that correspond with the times you want the lights ON. Each pin represents 30 minutes.
- Once your desired times are set, slide the switch on the lower right to the clock position. Plug the lights into the timer and the timer into the outlet. You can secure the timer box to the wall by sliding the slot on the back onto a single screw. The timer can be overridden by sliding the switch to the I position. When in the I position, the lights will be on permanently.
WARNING: Bypassing the transformer will cause the fixtures to fail. The transformer is an integral and required part of the system.
If the remote loses connection to the LED Transformer/Controller, most times it just needs to be reconnected.
- Unscrew the cover on the left side of the LED controller and remove it. This will give you access to the Address Setting Key button.
- Press down on the black key button until the indicator light is on.
- Finally, press any key on the remote. When the indicator light flashes, the controller and remote are relinked.
If rewiring is ever required, refer to the image at left for a correct colour
position that corresponds to your wire.
The Scott Aerator Awesome Warranty
All standard Scott Aerator products are unconditionally warranted for five
years against motor defects in materials or workmanship, under normal
operating conditions. All other product components are warranted for one year
from the date of purchase. Scott Aerator will repair or replace failed parts
under warranty when the defective unit is returned to the factory, shipping
prepaid, and factory inspection establishes that the part was defective. The
unit must be returned to the factory before shipment of replacement parts. All
parts replaced under this warranty will be returned with shipping prepaid.
Scott Aerator will not be liable for consequential damage nor for any costs
associated with removal or attempts to repair components in the field.
13245 Barry Street, Holland, MI 49424 scottaerator.com information@scottaerator.com 800-WATER-45 (800-928-3745 616-392-8882
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>