DORMAN 924-789 Ignition Lock Cylinder Instruction Manual

DORMAN 924-789 Ignition Lock Cylinder

Product Information

Specifications:

• Product Number: 924-789
• Product Name: Ignition Lock Cylinder
• Recommended Usage: Refer to the appropriate shop manual for specific service procedures
• Manufacturer: Not specified

Product Usage Instructions

Removal Instructions:

1. Disconnect the battery.
2. Remove the trim panel surrounding the ignition lock by removing retaining screws or retainers.
3. Remove the ignition lock trim bezel by gently prying it off with a plastic trim tool or equivalent.
4. Remove the key illumination ring if equipped.
5. Insert the ignition key into the lock cylinder and rotate to the ACC (accessory) position.
6. Using a small screwdriver or similar tool, push in the retaining pin on the underside of the lock housing while pulling out the lock.
7. Remove the lock cylinder from the steering column by pulling the cylinder outwards while keeping the pin pushed in.

Installation Instructions:

1. Insert the key into the replacement ignition lock cylinder.
2. Rotate the key to the ACC (accessory) position.
3. Insert the ignition lock cylinder into the ignition lock cylinder case until the retaining pin engages in the hole.
4. Remove the key from the ignition lock cylinder.
5. Reinstall the key illumination ring and screw if equipped.
6. Reinstall the lock trim bezel by gently snapping it back into place.
7. Reinstall the lower dash trim panel under the steering column and tighten screws.
8. Reconnect the battery.

Frequently Asked Questions (FAQ)

• Q: What should I do if I encounter difficulties during installation?
  A: Please contact our Technical Assistant at 1-800-523-2492 for any challenges or suggestions regarding the installation or operation of this product.

ATTENTION:
Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not have a service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician. Pay special attention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.

REMOVAL/INSTALL OF IGNITION LOCK CYLINDER (924-789) Geo Prizm 1997–93, Toyota Corolla 1997–93

PLEASE WEAR SAFETY GLASSES!

Removal Instructions

• STEP 1: Disconnect battery.
• STEP 2: Remove the trim panel surrounding the ignition lock by removing retaining screws or retainers. NOTE: The trim panels vary among models. Use caution upon the removal process to prevent damage tothe  trim panel.
• STEP 3: Remove the ignition lock trim bezel by gently prying it off with a plastic trim tool or equivalent.
• STEP 4: Remove the ey illumination ring if equipped.
• STEP 5: Insert the ignition key into the lock cylinder and rotate to the ACC (accessory) position.
• STEP 6: Using a small screwdriver or similar tool, push in the retaining pin on the underside of the lock housing while pulling out the lock.
• STEP 7: Remove the lock cylinder from the steering column by pulling the cylinder outwards while keeping the pin pushed in.

Installation Instructions

• STEP 1: Insert the key into the replacement ignition lock cylinder.
• STEP 2: Rotate the key to the ACC (accessory) position.
• STEP 3: Insert the ignition lock cylinder into the ignition lock cylinder case until the retaining pin engages in the hole.
• STEP 4: Remove the key from the ignition lock cylinder.
• STEP 5: Reinstall the key illumination ring and screw if equipped.
• STEP 6: Reinstall the lock trim bezel by gently snapping it back into place.
• STEP 7: Reinstall the lower dash trim panel under the steering column and tighten the screws.
• STEP 8: Reconnect the battery.

We appreciate your opinions regarding this product!
Please call our Technical Assistant with any challenges or suggestions regarding the installation or operation of this product. 1-800-523-2492

Disclaimer

Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations. Please consult with a qualified auto technician before attempting to perform any work you are not qualified to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damage or personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffic Safety Administration). Be sure that your work is performed by such standards and that you do not disable any motor vehicle safety features.

©2018 Dorman Products, Inc.
No reproductions in whole or in part without prior written approval.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>