Carrier 7C-SN-C4X-X HyperStat Split User Manual

Carrier 7C-SN-C4X-X HyperStat Split

Product Information

Specifications

• Power: 24V AC/DC
• Operating temperature: –
• Protection: IP 20, NEMA Type 1
• Pollution grade: 2
• Certification: ROHS
• Inputs and Outputs: (8) Universal Inputs, (4) 0-10v or 4-20ma analog outputs, (8) Relays 24V AC/DC, 1A rated, 1.77 240*128-pixel RGB TFT display
• Communication: 3-wire sensor bus for daisy-chained sensor communication and low-power 3V DC, 4 wire RS-485 interface
• Mounting: Firmly on the wall using the self-tapping screws or DIN clip (to be ordered separately)
• Storage temperature: –

Product Usage Instructions

Precautions

1. Installation and servicing should only be done by trained and qualified service personnel due to electrical hazards.

Mounting

1. Install the Connect Module on a DIN rail or directly on a wall using the bracket (to be ordered separately).
2. To lock the DIN clip to the Connect Module, use the screws provided to the back of the Connect Module.
3. To remove the wire, lift the flap up and pull the wire out.
4. To remove the Connect Module from the DIN rail, hold it firmly and pull upwards to separate from the DIN rail.

FAQ

• Q: Where can I find more information on wiring and commissioning?
  • A: For more information on wiring, commissioning, or usage of the ClimaVision product line, please refer to any documentation provided with the job. If no documentation was provided, visit the ClimaVision Help Center (infohhub.carrierclimavision.com) or scan the QR code on page 1 of the manual.
• Q: How can I get technical support?
  • A: If you need additional help, reach out to your local Carrier distributor for support.

INTRODUCTION

Introducing the Connect Module! This powerful unit controller offers seamless integration with OWI sensors to help you easily monitor your building’s environment. With BACnet and Modbus capability, the Connect Module ensures compatibility with other systems. The onboard display simplifies programming, and with the ability to power and communicate with the HyperStat Lite, you’ll have complete control over your rooftop systems.

PACKAGE CONTENTS

• Connect Module
• Self-tapping screws
• Quick Start Guide

SPECIFICATIONS

Pollution grade: 2 Certification: ROHS

Inputs and Outputs| (8) Universal Inputs, (4) 0-10v or 4-20ma analog outputs, (8) Relays 24V AC/DC, 1A rated, 1.77″ 240*128-pixel RGB TFT display.
Communication| 3-wire sensor bus for daisy chained sensor communication and low-power 3V DC. 4 wire RS-485 interface. BACnet support coming soon.
Mounting| Firmly on the wall using the self-tapping screws or DIN clip (to be ordered separately).
Storage temperature| 32°F(0°C) to 122 °F(125°C)

PRECAUTIONS

• Install as per all state and local electrical codes.
• Do not mount the device in areas that expose the device to elements that could be beyond the operating temperatures.
• Do not mount directly in sunlight or any heating source

MOUNTING

1. Connect Module can be installed either on a DIN rail or directly to a Wall using the bracket (to be ordered separately). To lock the DIN clip to the Connect Module, use the screws provided (item-3, Fig-1a) to the back of the Connect Module. The DIN clip is spring-loaded and would snap on the DIN rail. To fix it to the wall bracket, use the screws provided (item-1, Fig-1b).
2. To wire the Connect module, remove the insulation of the cable for about 7mm (liitle over ¼ of an inch) lift the flap, insert the wire and push the flap down. Try pulling the wire out to make sure its firmly snapped in place. Refer to Figure 2 for details.
3. To remove the wire, lift the flap up and pull the wire out.
4. To remove the connect module from the DIN rail, hold the connect module firmly and pull it upwards. This will cause the spring to expand and the Connect module can be separated from the DIN rail.

CARRIER CLIMAVISION TECHNICAL SUPPORT

Installation and servicing of Control Systems can be hazardous due to electrical components. Only trained and qualified service personnel should install, repair or service control system components. For more information on wiring, commissioning, or usage of the ClimaVision product line, please refer to any documentation provided with the job. If no documentation was provided with the job, please use the ClimaVision Help Center (infohhub.carrierclimavision.com) where you can find application specific wiring schematics and helpful user guides and videos or scan the QR code on page 1. If you need help beyond that, please reach out to your local Carrier distributor for support

FCC  Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and all persons. This transmitter must not be co located or operating in conjunction with any other antenna or transmitter.

Canadian Compliance Statement

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

For more information, contact your local Carrier Controls Expert ©2024 Carrier. All Rights Reserved. Cat. No. 11-808-1083-01

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>