iBoard WB-DN209MD 6 Inch Tubular Drop Down Style Nerf Bars Running Boards Installation Guide

iBoard WB-DN209MD 6 Inch Tubular Drop Down Style Nerf Bars Running Boards

PARTS LIST

PROCEDURE

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. DRILLING MAY BE REQUIRED.

2. Starting at the Driver/Left front of the vehicle, remove the sealing tape covering the factory holes in the side of the inner panel, (Figure 1).

3. Determine the correct procedure to attach (1) Driver/Left Mounting Bracket for your model/year:
   Models without factory threaded inserts in body panel:
   a. Partially thread (1) 8mm Hex Bolt into the threaded end of (1) 8mm Bolt/Nut Plate, (Figure 2). Thread the Hex Bolt in until it is flush with the welded nut, (Figure 3). Use the Hex Bolt as a handle and insert the Bolt/Nut Plate into the oval hole, (Figure 4).
   b. Feed the threaded bolt on the Bolt Plate through one of the hex shaped factory holes.
   c. Thread (1) 8mm Plastic Retainer onto the threaded end and down tight against the body panel, (Figure 5). NOTE: The Plastic Retainer is designed to keep the Bolt/Nut Plate from falling into the body panel and to aid in Bracket installation.
   d. Select (1) Driver/Left Mounting Bracket. Attach the Bracket to the threads on the Plate with (1) 8mm Flat Washer, (1) 8mm Lock Washer and (1) 8mm Hex Nut, (Figure 6). Do not tighten hardware.
   e. Remove the 8mm Hex Bolt from the nut on the Bolt/Nut Plate from Step 3a. Rotate the Bolt on the Bolt/Nut Plate until the threaded nut lines up with the remaining hole in the Mounting Bracket and body panel, (Figure 6). Attach the Bracket to the threaded Nut Plate with (1) 8mm x 30mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat Washer, (Figure 7). Do not tighten hardware.
   Models with factory threaded inserts:
   a. Attach the driver side Front Bracket directly to the threaded inserts with (2) 8mm x 30mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washer, (Figures 8 & 9). Do not tighten hardware.

4. Next, select (1) Driver/Left Support Bracket. Attach the Bracket to the pinch weld with (2) 6mm Hex Bolts, (4) 6mm Flat Washers and (2) 6mm Nylon Lock Nuts, (Figure 10). Attach the Support Bracket to the Mounting Bracket with (1) 8mm Hex Bolt, (2) 8mmFlat Washers and (1) 8mm Nylon Lock Nuts, (Figure 11). Do not tighten hardware. IMPORTANT: 2009-10 models are not equipped with factory holes and will require drilling through the pinch weld to attach the Support Bracket. Do not drill through pinch weld at this time, (see Step 8).

5. Move along the side of the body panel to the center mounting location, (Figure 12). Repeat Steps 2—4 to attach (1) Driver/Left Mounting Bracket and (1) Support Bracket to the center location, (Figure 13).

6. Move to the rear location, (Figure 14). Repeat Steps 2—4 to attach (1) Passenger/Right Mounting Bracket (1) Passenger/Right Support Bracket to the rear location, (Figure 15).

7. Select the Driver/Left Running Board. Attach the Running Board to the rear faces of the Mounting Brackets with (6) 10mm Hex Bolts, (12) 10mm Flat Washers and (6) 10mm Nylon Lock Nuts, (Figures 16 & 17). Do not tighten hardware.

8. Properly level and adjust the Running Board and fully tighten all hardware. 2009-10 models requiring drilling for driver side Support Brackets:
   a. Make sure the Running Board is level to the vehicle. Adjust and tighten all mounting hardware.
   b. Line up the slots on the Support Brackets with the back of the pinch weld. Mark the location of the slots onto the pinch weld.
   c. Drill (2) 1/4” holes through the pinch weld for each Support Bracket. IMPORTANT: Do not drill too close to the bottom edge of the pinch weld. Adjust the Brackets as necessary to move the slots up the body panel away from the edge. Drill the holes toward the outside of the marked slots.
   d. Attach each Support Bracket to the pinch weld with (2) 6mm Hex Bolts, (4) 6mm Flat Washers and (2) 6mm Nylon Lock Nuts, (Figures 16—19). Check the Running Board for level then fully tighten all hardware.

9. Repeat Steps 2—8 to attach the Passenger/Right Running Board.

10. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

To protect your investment , wax this product after installing. Regular waxing is recommended to add a protective layer over the finish. Mild soap may be used to clean the Running Boards.

Driver Side Installation Pictured

(Fig 1) 2009-mid 2015 Driver/Left front mounting location (No factory holes in pinch weld on 2009-2011 models)

(Fig 2) 8mm Bolt-8mm Nut Plate, NOTE: 8mm Bolt-Nut Plate is not required on models with threaded inserts.

(Fig 3) Thread (1) 8mm Hex Bolt into the nut on the plate. Stop when bolt reaches end of nut as pictured

(Fig 4) Use the loose Hex Bolt as a handle. Insert the Bolt Plate into the oval hole and feed the threaded end out either factory hex shaped hole. IMPORTANT: Do not let go of the hex bolt until after Plastic Retainer has been threaded onto bolt (Fig 5)

(Fig 5) Thread Plastic Retainer onto Bolt Plate to hold Bole Plate in position.

(Fig 6) Attach Passenger/Right Front Bracket to Bolt Plate. Rotate Bolt Plate to line up with remaining factory hex shaped hole. (Driver front pictured)

(Fig 7) Remove 8mm Hex Bolt (see Fig 3). Rotate Bolt Plate to line up with remaining factory hex shaped hole.

(Fig 8) Driver side front mid 2015-on, an example of models with factory installed threaded inserts.

(Fig 9) Driver side front-models with factory installed threaded inserts. Bolt Plate not required

(Fig 10) Attach Support Bracket to back of pinch weld (models with factory holes in pinch weld only)

(Fig 11) Attach Support Bracket to back of Mounting Bracket

(Fig 12) Driver/Left center location

IMPORTANT: 2009-2010 models without holes in pinch weld will require drilling 1/4” holes through pinch weld to attach driver side front support bracket. Do complete installation of sidebars first, level sidebar before drilling holes for support bracket.

(Fig 13) (1) Driver/Left Front Mounting Bracket and Support attached to the center location

(Fig 14) Driver/Left rear mounting location

IMPORTANT: 2009-2010 models without holes in pinch weld will require drilling 1/4” holes through pinch weld to attach driver side front support bracket. Do complete installation of sidebars first, level sidebar before drilling holes for support bracket.

(Fig 15) Driver/Left Rear Mounting Bracket and Support Bracket attached to the rear location.

(Fig 16) Attach the Driver/Left Running Board to the rear faces of the Mounting Brackets.

(Fig 17) Driver/Left NB1 Running Board attached to the Front Mounting Bracket.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>