iBoard IB-P095C 6 Inch Aluminum Running Boards Nerf Bars Side Steps Installation Guide
- June 1, 2024
- iBoard
Table of Contents
iBoard IB-P095C 6 Inch Aluminum Running Boards Nerf Bars Side Steps
Specifications:
- Product Model: IB-P095C&J
- Mounting Type: Rocker Panel Mount
- Installation: No Drilling Required
Product Usage Instructions:
Step 1: Driver Side Front Mounting Bracket Installation
Start installation on the driver side of the vehicle. Locate the driver side front bracket mounting location. Select (1) Mounting Bracket, install with (2) M8 Hex Flange Nuts. Do not fully tighten hardware at this time.
Step 2: Driver Side Center & Rear Mounting Bracket Installation
Move to the Driver Side Center & Rear Mounting location. Repeat Step 1 to install the Driver Side Center & Rear Mounting Bracket. Note: All (3) Driver Side Mounting Brackets are universal.
Step 3: Slider and Step Bar Installation
Do periodic inspections to the installation to make sure that all hardware is secure and tight. Use mild soap/non-abrasive products for cleaning only.
Frequently Asked Questions
Q: Is drilling required for installation?
A: No, drilling is not required for installation. The product is designed for rocker panel mounting.
Q: How should I clean the bars/boards?
A: To protect your bars/boards, use mild soap with non-abrasive products for cleaning.
PART#: IB-P095C&J
READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.
- ROCKER PANEL MOUNT
- NO DRILLING REQUIRED
| Fastener Size | Tightening Torque (ft-lbs) | Required |
|---|---|---|
| 6mm | 6-7 | X |
| 8mm | 16-18 | √ |
| 10mm | 31-32 | X |
| 12mm | 56-58 | X |
| 14mm | 92-94 | X |
PART LIST
Hardware Package A (For
Bracket Installation)
INSTALLATION
STEP 1
Start installation on the driver side of the vehicle. Locate the driver side
front bracket mounting location. Select (1) Mounting Bracket, install with (2)
M8 Hex Flange Nuts. Do not fully tight-en hardware at this time.
STEP 2
Move to the Driver Side Center & Rear Mounting location. Re-peat Step 1 to
install the Driver Side Center & Rear Mounting Bracket .
Note: All (3) Driver Side Mounting Brackets are universal.
STEP 3
Once all (3) Driver side mounting brackets are installed, then proceed to the
Step Bar installation. (Figs 2 & 3)
- Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;
- Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.
- Slide the Slider (with carriage bolts) to the Step Bar.
- Repeat to install the other (2) sliders to the step bar.
- Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brackets. Secure the Step Bar to the installed Brackets by using (6) M8 Large Flat Washers and (6) M8 Nylon Lock Nuts and (3) Sliders, (Fig 3). Do not fully tighten hardware at this time.
Note: The Sliders are packed with the Mounting Brackets.
Level and adjust the Step Bar and fully tighten all hardware.
Repeat Steps 1-3 for the other side Step Bar installation. The installation is completed!!!
Attention
Do periodic inspections to the installation to make sure that all hardware is
secure and tight.
In order to protect your bars/boards, please use mild soap/non-abrasive
products for cleaning only.
Customer Support: info@iboardauto.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>