iBoard TG-RS6D60208 6 Riser Running Boards Installation Guide
- June 1, 2024
- iBoard
Table of Contents
iBoard TG-RS6D60208 6 Riser Running Boards
Product Information
Specifications:
- Model: TG-RS6D60208
- Material: Steel
- Size: 6 inches
- Fastener Sizes and Torque Values:
Fastener Size | Class 8.8 Torque (ft-lbs) | Class 10.9 Torque (ft-lbs) |
---|---|---|
6mm | 6-7 | 6-7 |
8mm | 15-16 | 22-23 |
10mm | 31-32 | 44-45 |
12mm | 54-55 | 78-79 |
14mm | 87-88 | N/A |
Product Usage Instructions
Before Installation:
Read the instructions carefully before starting installation.
Remove contents from the box and verify all parts are present. If any missing
parts or damage is found, take a picture for claim purposes. To file a claim,
visit www.tygerauto.com/contact.
Frequently Asked Questions (FAQ):
Q: What should I do if I find missing parts or damage before
installation?
A: Take a picture for claim purposes and visit
www.tygerauto.com/contact to file a claim.
BEFORE INSTALLATION
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. FAILURE TO IDENTIFY DAMAGE BEFORE INSTALLATION COULD LEAD TO A REJECTION OF ANY CLAIM. IF MISSING PARTS OR ANY DAMAGE FOUND, PLEASE TAKE A PICTURE FOR THE CLAIM PURPOSE. TO FILE YOUR CLAIM, PLEASE VISIT: WWW.TYGERAUTO.COM/CONTACT
TORQUE VALUES
Fastener Size | Class 8.8 Torque (ft-lbs) | Class 10.9 Torque (ft-lbs) |
---|---|---|
6mm | 6-7 | 6-7 |
8mm | 15-16 | 22-23 |
10mm | 31-32 | 44-45 |
12mm | 54-55 | 78-79 |
14mm | 87-88 | 125-126 |
Parts List
- x1 Driver/Left 6inch Tyger Sidebar
- x1 Passenger/Right 6inch Tyger Sidebar
- x2 Front Upper Mounting Brackets
- x2 Front Lower Mounting Brackets
- x2 Center Mounting Brackets
- x2 Rear Mounting Brackets
- x4 Center/Rear Support Brackets
- x12 8mm x 25mm Combo Bolts
- x4 8mm x 25mm Hex Bolts
- x22 8mm x 24mm OD x 2mm Flat Washers
- x8 8mm x 16mm OD x 1.6mm Flat Washers
- x26 8mm Nylon Lock Nuts
PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
USE WIRE BRUSH TO CLEAN MOUNTING STUDS OF PAINT AND DEBRIS.
INSTRUCTION
STEP 1
Start the installation under the Driver/Left side of the vehicle. Locate
the front (3) factory studs along the inner side of the body panel (Fig 1).
Driver/Left Side Installation Pictured
STEP 2
Select (1) Front Upper Mounting Bracket. Attach the Mounting Bracket to the
(3) factory studs with (3) 8mm x 24mm Flat Washers and (3) 8mm Nylon Lock Nuts
(Fig 2). DO NOT tighten hardware.
STEP 3
Select (1) Front Lower Mounting Bracket. Attach the Lower Bracket to the
rear facing side of vertical tab on the Upper Bracket with (2) 8mm Hex Bolts,
(4) 8mm x 16mm Flat Washers and (2) 8mm Nylon Lock Nuts (Fig 3). DO NOT
tighten hardware.
STEP 4
Move to the center location (Fig 4). Select (1) Support Bracket. Attach the
Support Bracket to the (2) lower threaded studs with (2) 8mm x 24mm Flat
Washers and (2) 8mm Nylon Lock Nuts (Fig 5). Select (1) Center Mounting
Bracket and attach to the Support Bracket and upper threaded stud with (2) 8mm
x 24mm Flat Washers and (2) 8mm Nylon Lock Nuts (Fig 6). DO NOT tighten
hardware.
Driver/Left Side Installation Pictured
STEP 5
Repeat STEP 4 to attach (1) Rear Mounting Bracket and (1) Support Bracket
to the rear mounting location (Fig 7). DO NOT tighten hardware.
STEP 6
Select the Driver/Left 6inch Tyger Sidebar. Attach the Running Board to the
Mounting Brackets with (6) 8mm Combo Bolts (Fig 8). DO NOT tighten hardware.
STEP 7
Level and adjust the Running Board as necessary and fully tighten all
hardware.
STEP 8
Repeat STEPs 1-6 to attach the Passenger/Right 6inch Tyger Sidebar to the
vehicle.
STEP 9
Do periodic inspections to the installation to make sure that all hardware is
secure and tight.
Customer Support: www.TygerAuto.com/Contact
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>