iBoard IB-213C Stainless Steel Black Running Board Installation Guide

iBoard IB-213C Stainless Steel Black Running Board

Product Specifications

• Part Number: IB-213C&H
• Fastener Size: 6mm, 8mm, 10mm, 12mm, 14mm
• Tightening Torque (ft-lbs): 6-7, 16-18, 31-32, 56-58, 92-94

Product Usage Instructions

Part List:

• Driver Side Step Bar
• Driver Front Support Bracket (DFS)
• Passenger Side Step Bar
• Passenger Front Support Bracket (PFS)
• Driver Front Mounting Bracket (DFM)
• Passenger Front Mounting Bracket (PFM)
• Driver Rear Mounting Bracket (DRM)
• Passenger Rear Mounting Bracket (PRM)

Hardware Package A (For Bracket Installation):

Hardware Package B (For Stainless Steel Step Bar Installation):

Installation Steps:

1. Step 1:
   Start the installation under the passenger side of the vehicle. Locate the factory holes and insert the M10 Passenger Double Nut Plate through the large hole in the frame.

2. Step 2:
   Select and hang the Passenger Front Mounting Bracket to the installed M10 Double Nut Plate using the provided hardware.

3. Step 3:
   Bolt the Passenger Front Support Bracket to the factory hole and then attach it to the back of the Passenger Front Mounting Bracket using the included hardware.

4. Step 4:
   Note: On some models, drilling may be required to install the product.

Frequently Asked Questions (FAQ):

• Q: Do I need special tools for installation?
  A: The product installation may require basic tools like a drill and wrench set. Please refer to the user manual for specific tool requirements.

• Q: How do I contact customer support for assistance?
  A: For customer support, you can email info@iboardauto.com or refer to the contact information provided in the manual.

iBoard® by APS

• READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.
• • ROCKER PANEL MOUNT
• • DRILLING MAY BE REQUIRED

PART LIST

Hardware Package A (For Bracket Installation)

Item| QTY| Description| Item| QTY| Description
1#| 1| M10 Driver Double Nut Plate| 4#| 20| M10 Large Flat Washers
2#| 1| M10 Passenger Double Nut Plate| 5#| 12| M10 Lock Washers
3#| 12| M10X1.5-30mm Hex Bolts| 6#| 8| M10X1.5 Hex Nuts

Hardware Package B (For Stainless Steel Step Bar Installation)

Item| QTY| Description| Item| QTY| Description
1#| 8| M8X1.25-35mm Carriage Bolts| 3#| 8| M8 Nylon Lock Nuts
2#| 8| M8 Large Flat Washers| 4#| 4| Sliders (Packed with Step Bars)

Installation

1. STEP 1
   Start the installation under the passenger side of the vehicle. Locate the three factory holes (one large, two small) in the frame channel next to the front body mount. Insert the smaller end of the M10 Passenger Double Nut Plate through the large hole in the frame and line it up with the smaller hole, (Fig 1).

2. STEP 2
   Select (1) Passenger Front Mounting Bracket, hang it to the installed M10 Double Nut Plate with the included (2) M10X1.5-30mm Hex Bolts, (2) M10 Lock Washers and (2) M10 Flat Washers, (Fig 2). Do not fully tighten hardware at this time.

3. STEP 3
   Locate the factory hole on the edge of the floor panel behind the passenger front body mount. Select the Passenger Front Support Bracket (PFS). Bolt the flat end of the Support Bracket to the factory hole using the included (1) M10 X 1.5-30mm Hex Bolt, (1) M10 Lock Washer, (2) M10 Flat Washers and (1) M10 Hex Nut, (Fig 3a).
   Line up the bent end of the Support Bracket with the back of the Passenger Front Mounting Bracket. Bolt the Support Bracket using the included (1) M10 X 1.5-30mm Hex Bolt, (1) M10 Lock Washer, (2) M10 Flat Washers and (1) M10 Hex Nut, (Fig 3b). Do not fully tighten hardware at this time.

4. STEP 4
   Insert the Passenger Rear Mounting Bracket (PRM) between the inner side panel and the outer body of the vehicle, (Fig 4 & 5). Line up the hole in the 90˚ bend with the factory hole in the cab toward the bed and secure it using the included (1) M10 X 1.5-30mm Hex Bolt, (1) M10 Lock Washer, (2) M10 Flat Wash- ers and (1) M10 Hex Nut. Attach the upper mounting location in the Rear Bracket to factory hole in the inner side panel using the included (1) M10 X1.5-30mm Hex Bolt, (1) M10 Lock Wash-er, (2) M10 Flat Washers and (1) M10 Hex Nut, (Fig 4 & 5). Do not fully tighten hardware at this time.
   NOTE: On some models, it may be necessary to drill a hole through the side panel for the hex bolts.
   IMPORTANT: Any cutting or drilling tool may break or shatter. Government regulations require safety glasses & equipment at all times when cutting or drilling.

5. STEP 5
   Once all (2) Passenger side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 6 & 7)

6. Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;

7. Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.

8. Slide the Slider (with carriage bolts) to the Step Bar.

9. Repeat to install the other (1) slider to the step bar.

10. Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brackets. Secure the Step Bar to the installed Brackets by using (4) M8 Large Flat Washers and (4) M8 Nylon Lock Nuts and (2) Sliders, (Fig 7). Do not fully tighten hardware at this time.
    Note: The Sliders are packed with the Step Bars.
    Level and adjust the Step Bar and fully tighten all hardware.
    Repeat Steps 1-5 for the other side Step Bar installation. The installation is completed!!!

Attention

• Do periodic inspections to the installation to make sure that all hardware is secure and tight.
• In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.

Customer Support: info@iboardauto.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>