iBoard IB-P008C 6-inch Aluminum Running Boards Nerf Bars Side Instruction Manual
- June 1, 2024
- iBoard
Table of Contents
IB-P008C 6-inch Aluminum Running Boards Nerf Bars Side
Instruction Manual
IB-P008C 6-inch Aluminum Running Boards Nerf Bars Side
READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.
- ROCKER PANEL MOUNT
- NO DRILLING REQUIRED
| Fastener Size | Tightening Torque (ft-lbs) | Required |
|---|---|---|
| 6mm | 6-7 | X |
| 8mm | 16-18 | √ |
| 10mm | 31-32 | √ |
| 12mm | 56-58 | X |
| 14mm | 92-94 | X |
Hardware Package A (For Bracket Installation)
Item| QTY| Description| Item| QTY| Description
1#| 2| Driver / Passenger Front Mounting Brackets| 5#| 2| Plastic Washers
2#| 2| Driver / Passenger Rear Mounting Brackets| 6#| 8| M10 Large Flat
Washers
3#| 4| M10 Large Double Bolt Plates| 7#| 8| M10 Lock Washers
4#| 1| M10 Small Double Bolt Plates| 8#| 8| M10 Hex Nuts
Hardware Package B (For Step Bar Installation)
Item| QTY| Description| Item| QTY| Description
1#| 8| M8X1.25-35mm Carriage Bolts| 3#| 8| M8 Nylon Lock Nuts
2#| 8| M8 Large Flat Washers| 4#| 4| Sliders (Packed with Mounting Brackets)
STEP 1
Start installation from the Driver Side Front of the vehicle. Remove the large
oval rubber cover located on the inner side of the body panel if equipped,
(Fig 1). Insert (1) M10 Large Double Bolt Plate into the oval hole, (Fig 2)
and pull it back into position against the inner of the body panel, (Fig
3).
(Fig 1) Driver Side Front Mounting Location 
(Fig 2) M10 Large Double Bolt Plate Installation
(On Driver Side Front Mounting Location) 
(Fig 3) M10 Large Double Bolt Plate Installed (On
Driver Side Front Mounting Location)
STEP 2
Select (1) Driver Front Mounting Bracket. Secure the Driver Front Mounting
Bracket to the installed M10 Large Double Bolt Plate with (2) M10 Lock
Washers, (2) M10 Large Flat Washers and (2) M10 Hex Nuts, (Fig 4). Do not
fully tighten hardware at this time. 
STEP 3
Move to Driver Side Rear Mounting Location. Repeat Steps 12 for Driver Rear
Mounting Bracket installation. Do not fully tighten hardware at this time.
NOTE: On 3-door models, insert the M10 Small Double Bolt Plate into the large
round hole and line up with the smaller round hole, (Fig 5). Then use the
included Plastic Washers to hold the Bolt Plate in position and secure the
Bracket as previously described in Steps 1-2.
STEP 4
Once all (2) Driver side mounting brackets are installed, then proceed to
the Step Bar installation. (Figs 6 & 7) (1) Select (1) Slider and (2)
M8X1.25-35mm Carriage Bolts; (2) Install (2) M8X1.25-35mm Carriage Bolts in
(1) Slider. (3) Slide the Slider (with carriage bolts) to the Step Bar. (4)
Repeat to install the other (1) slider to the step bar. (5) Attach the Step
Bar (with the Sliders) onto the installed mounting brackets. Position the
Sliders to the installed brackets. Secure the Step Bar to the installed
Brackets by using (4) M8 Large Flat Washers and (4) M8 Nylon Lock Nuts and (2)
Sliders, (Fig 7). Do not fully tighten hardware at this time.
Note: The Sliders are packed with the Mounting Brackets. Level and adjust
the Step Bar and fully tighten all hardware. Repeat Steps 1-4 for the other
side Step Bar installation. The installation is completed!!!
Attention
Do periodic inspections to the installation to make sure that all hardware is
secure and tight.
In order to protect your bars/boards, please use mild soap/non-abrasive
products for cleaning only. 
https://www.iboardauto.com/iboard-videos/
Customer Support: info@iboardauto.com
Rev. 20230701
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>