iBoard IB-065CH Stainless Steel Polished Silver 6 inches Running Instruction Manual

iBoard IB-065CH Stainless Steel Polished Silver 6 inches Running

Specifications:

• Product Name: Body Frame Mount Step Bar
• Part Number: IB-065C&H
• Fastener Sizes: 6mm, 8mm, 10mm, 12mm, 14mm
• Tightening Torque (ft-lbs):
  • 6mm: 6-7
  • 8mm: 16-18
  • 10mm: 31-32
  • 12mm: 56-58
  • 14mm: 92-94

Product Usage Instructions

Step 1: Installation of Passenger Side Mounting Brackets
Start installation from the passenger side of the vehicle. Remove the body mount bolts from body mounts.

1. Select the Passenger Front Mounting Bracket (PFM), Passenger Center Mounting Bracket (PCM), and Passenger Rear Mounting Bracket (PRM).
2. Bolt the (3) mounting brackets to the vehicle using (3) M12X1.75-120mm Hex Bolts, (3) M12 Lock Washers, and (3) M12 Flat Washers. Do not fully tighten hardware at this time.

Step 2: Step Bar Installation

1. Select a Slider and (2) M8X1.25-35mm Carriage Bolts.
2. Install (2) M8X1.25-35mm Carriage Bolts in the Slider.
3. Slide the Slider (with carriage bolts) onto the Step Bar.
4. Repeat to install the other sliders on the Step Bar.
5. Attach the Step Bar (with Sliders) onto the installed mounting brackets. Secure using (6) M8 Large Flat Washers, (6) M8 Nylon Lock Nuts, and (3) Sliders. Do not fully tighten hardware at this time.
6. Level and adjust the Step Bar and fully tighten all hardware.
7. Repeat Steps 1-2 for the other side Step Bar installation. The installation is completed!

FAQ:

Q: What should I use to clean the bars/boards?
A: In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.

iBoard® by APS

• READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.
• • BODY FRAME MOUNT
• • NO DRILLING REQUIRED

PART LIST

Hardware Package A (For Bracket Installation)

Item| QTY| Description| Item| QTY| Description
1#| 6| M12X1.75-120mm Hex Bolts| 3#| 6| M12 Lock Washers
2#| 6| M12 Flat Washers| | |

Hardware Package B (For Stainless Steel Step Bar Installation)

Item| QTY| Description| Item| QTY| Description
1#| 12| M8X1.25-35mm Carriage Bolts| 3#| 12| M8 Nylon Lock Nuts
2#| 12| M8 Large Flat Washers| 4#| 6| Sliders (Packed with Step Bars)

Installation

1. STEP 1
   Start installation from the passenger side of the vehicle. Re-move the body mount bolts from body mounts.
   Select the Passenger Front Mounting Bracket (PFM), Passen-ger Center Mounting Bracket (PCM) and Passenger Rear Mounting Bracket (PRM). Bolt the (3) mounting brackets to the vehicle with (3) M12X1.75-120mm Hex Bolts, (3) M12 Lock Washers and (3) M12 Flat Washers (Fig 1). Do not fully tighten hardware at this time.

2. STEP 2
   Once all (3) Passenger side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 2 & 3)

3. Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;

4. Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.

5. Slide the Slider (with carriage bolts) to the Step Bar.

6. Repeat to install the other (2) sliders to the step bar.

7. Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brack-ets. Secure the Step Bar to the installed Brackets by using (6) M8 Large Flat Washers and (6) M8 Nylon Lock Nuts and (3) Sliders, (Fig 3). Do not fully tighten hardware at this time.
   Note: The Sliders are packed with the Step Bars.
   Level and adjust the Step Bar and fully tighten all hardware.
   Repeat Steps 1-2 for the other side Step Bar installation. The installation is completed!!!

Attention

• Do periodic inspections to the installation to make sure that all hardware is secure and tight.
• In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.

Customer Support: info@iboardauto.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>