iBoard IB-228C 5 Inch Stainless Steel Black Running Boards Installation Guide
- June 1, 2024
- iBoard
Table of Contents
iBoard® by APS
PART#: IB-228C&H
IB-228C 5 Inch Stainless Steel Black Running Boards
Scan for Installation
https://www.iboardauto.com/iboard-videos/
READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.
ROCKER PANEL MOUNT
NO DRILLING REQUIRED
| Fastener Size | Tightening Torque (ft-lbs) | Required |
|---|---|---|
| 6mm | 6-7 | X |
| 8mm | 16-18 | √ |
| 10mm | 31-32 | X |
| 12mm | 56-58 | X |
| 14mm | 92-94 | X |
PART LIST
Mounting Bracket List
Item| QTY| Description| Item| QTY| Description
1#| 3| Driver Front/Center/Rear Mounting Brackets| 2#| 3| Passenger
Front/Center/Rear Mounting Brackets
Hardware Package A (For Bracket Installation)
Item| QTY| Description| Item| QTY| Description
1#| 12| M8 Large Flat Washers| 2#| 12| M8X1.25 Nylon Lock Nuts
Hardware Package B (For Stainless Steel Step Bar Installation)
Item| QTY| Description| Item| QTY| Description
1#| 12| M8X1.25-35mm Carriage Bolts| 3#| 12| M8 Nylon Lock Nuts
2#| 12| M8 Large Flat Washers| 4#| 6| Sliders (Packed with Step Bars)
STEP 1
Start installation from the driver side front of the vehicle. Locate the (2)
factory threaded studs located on the side of the inner body panel, (Fig 1).
STEP 2
Select the Driver Front Mounting Bracket. Attach to the (2) factory threaded
studs with (2) M8 Large Flat Washers and (2) M8X1.25 Nylon Lock Nuts, (Fig 2).
Do not fully tighten hardware at this time.
STEP 3
Move to the center & rear mounting location. Repeat Steps 1 – 2 for Driver
Center & Rear Mounting Brackets.
Note: All (3) Driver Side Mounting Brackets are universal.
STEP 4
Once all (3) Driver side mounting brackets are installed, then proceed to the
Step Bar installation. (Figs 3 & 4)
- Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;
- Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.
- Slide the Slider (with carriage bolts) to the Step Bar.
- Repeat to install the other (2) sliders to the step bar.
- Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brackets.
Secure the Step Bar to the installed Brackets by using (6) M8 Large Flat Washers and (6) M8 Nylon Lock Nuts and (3) Sliders, (Fig 4).
Do not fully tighten hardware at this time.
Note: The Sliders are packed with the Step Bars.
Level and adjust the Step Bar and fully tighten all hardware.
Repeat Steps 1-4 for the other side Step Bar installation. The installation is
completed!!!
NOTE: All (3) Passenger Side Mounting Brackets are universal.
Attention
Do periodic inspections to the installation to make sure that all hardware is
secure and tight.
In order to protect your bars/boards, please use mild soap/non-abrasive
products for cleaning only.
Customer Support: info@iboardauto.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>