FORUM LIGHTING SPA 38570 – E Como 3PK Adjustable Recessed Downlights Installation Guide
- June 1, 2024
- Forum Lighting
Table of Contents
FORUM LIGHTING SPA 38570 – E Como 3PK Adjustable Recessed Downlights
Specifications:
- Part No.: 38570
- Description: Como 3PK Adjustable Recessed Downlights
- Wattage: 5W
- Fire Rated Downlight
- Beam Angle: 60 degrees
- Cut Out Diameter: 70mm
- Lumen Output: 500 Lm
- IP Rating: IP65
- Power Factor: >0.85
- CRI: >80
- Class Rating: Class II
- Colour Temperature: 4000K
- Input Voltage: 220-240V AC, 50/60Hz
Product Usage Instructions
Important Safety Information:
- Always switch off the mains power supply before installation or servicing.
- Ensure adequate free-air ventilation around the luminaire at all times.
- Do not install into damp or newly plastered ceilings.
Installation Steps:
- Select the mounting position in the ceiling and cut out a circular hole of 70mm in diameter.
- Pull the main supply cable through the hole and connect it to the terminals, observing the correct polarity.
- Close the terminal block cover securely and reconnect the main power supply.
- Test the installation for proper operation.
Terminations:
Live supply to L = (Brown or Red), Earth to E = (Green/Yellow), Neutral to N =
(Blue or Black).
Disposal Instructions:
This product should be disposed of responsibly at the end of its life. Please
recycle where facilities exist.
FAQ:
-
Q: What should I do if I receive an item with broken or missing parts?
A: Please contact the helpline at 0333 0050077 with your details and product reference for assistance. -
Q: Can this product be recycled?
A: Yes, please check with your Local Authority or retailer for recycling advice as per the Waste Electrical and Electronic Equipment Directive.
Please read these instructions carefully before installation Leave a copy for the user/maintenance engineer for future reference
Important Safety Information
- It is recommended that this luminaire is installed, inspected and maintained by a qualified electrician.
- Installation should be carried out by the latest edition of the IEE Wiring Regulations (BS 7671) and the latest Building Regulations. If in doubt, consult a qualified electrician.
- This product is designed for connection to a 220-240V~50/60Hz supply.
- Before commencing any installation or maintenance work, ensure that the electrical mains supply is isolated and circuit fuses are removed or switched off.
- Ensure that all electrical connections are tight with no loose strands including factory-made connections.
- This product is fire-rated.
- Mineral wool insulation material can be loosely laid across the luminaire but not compressed.
- Please note the IP rating of this luminaire when deciding the location for installation. IP65 (Below the ceiling), IP20 (Recessed parts).
- This luminaire is suitable for indoor use only.
- This product is dimmable. Dimmer type compatibility and Min/Max wattage recommended loadings must be observed.
- This is a Classll construction luminaire
- This luminaire is suitable for use in ambient temperatures of – 10 °C to + 40 °C.
- MCBs may require to be updated to allow for increased initial inrush current.
- Do not carry out any insulation resistance tests with the luminaire connected to the lighting circuit.
- The LED light source fitted in this product is non-replaceable. The whole luminaire must be replaced when the LED reaches the end of its life.
Technical Specifications
| Part No. | Description | Wattage | Measurement | Beam Angle |
|---|---|---|---|---|
| 38570 | Fire Rated Downlight | 5 W | 88 x 30 mm | 60degree |
| Cut Out Diameter | Lumen Output | IP Rating | Power Factor | CRI |
Colour Temperature
---|---|---|---|---|---|---
70 mm| 50 0 Lm| IP65| > 0. 8 5| > 8 0| Class I| 4000K
Features
Dimension
Important Installation Information
Always switch off the mains power supply before installation or servicing. Ensure that there is adequate free-air ventilation around the luminaire at all times. Do not install this product into damp or newly plastered ceilings.
- This luminaire should be mounted on a flat, smooth surface. Ensure that the mounting area is clean and free from any obstructions. The installation must not infringe on gas/water pipes or any other electrical cables or services that may be hidden behind the ceiling.
- This product is rated IP65 and is suitable for installation in bathroom zones 1 and 2 as defined by the National Wiring Regulations.
- Select the required mounting position in the ceiling and cut out a circular hole 70mm in diameter. Do not exceed the cutting diameter and ensure that cutouts are spaced adequately to provide clearance from any joists, beams or cables within the ceiling void.
- Pull the main supply cable through the hole and open the terminal block cover. Connect the main supply cable to the terminals ensuring that the correct polarity is observed. Close the terminal block cover tightly to secure the cable in place.
- Feed the excess main supply cable back through the hole and into the ceiling void. With the spring clips held in the upward position, tilt and insert the connector block and luminaire through the cutout hole and into the ceiling void, take care not to trap any cables. The spring clips will be located on the top of the ceiling surface to provide a secure installation. Ensure that the rubber seal ring is securely in place on the back of the bezel housing and that the luminaire is fitted centrally to the cutout hole.
Reconnect the mains power supply and test the installation for correct and satisfactory operation.
- This luminaire can be loosely covered with mineral wool insulation material. However, minimum clearance distances around the lu mi name must be observed: 25mm above the top of the luminaire, 75mm to all sides of the luminaire and 0.5m minimum distance between luminaires.
- When removing the luminaire for maintenance or changing the bezel, allow sufficient time for the product to cool before handling.
This product should be disposed of responsibly at the end of its life. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice (Waste Electrical and Electronic Equipment Directive)
Helpline
If you receive this item with parts broken or missing, please telephone: 0333 0050077.
Please have ready your name, address, tel. no., product reference, where purchased and parts required. An answering service is in operation outside office hours and during busy periods. We regret that we are unable to advise on internal house wiring.
- Cascade Holdings Ltd, Gorse Mill, Gorse Street, Chadderton, Oldham. OL9 9RJ
- EU Authorised Representative: Authorised Rep Compliance, Ground Floor, 71 Lower Baggot Street, Dublin, Ireland, DO2P593.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>