TAC 73350B Bull Bar Instruction Manual
- June 1, 2024
- TAC
Table of Contents
TAC 73350B Bull Bar
Product Specifications
- Product: Bull Bar for 2022-2024 Toyota Tundra
- Part Number: 73350B
- Includes:
- 1 Bull Bar
- 1 Driver/Left Mounting Bracket
- 1 Passenger/Right Mounting Bracket
- 1 Driver/Left Support Bracket
- 1 Passenger/Right Support Bracket
- 2 10mm x 35mm Bolt Plates
- 6 10mm x 35mm Hex Bolts
- 14 10mm x 30mm OD x 2.5mm Flat Washers
- 8 10mm Lock Washers
- 8 10mm Hex Nuts
- 2 10mm Fish Wires
Product Usage Instructions
-
1. Remove contents from the box and verify all parts are present. -
Read the instructions carefully before starting the installation, noting possible interference with front-mounted sensors.
-
Start the installation under the Passenger/Right front side of the vehicle by locating the end of the frame just behind the bumper and temporarily removing the (4) factory bolts.
-
To protect your investment, wax the product after installing. Regular waxing is recommended to add a protective layer over the finish. Avoid using abrasive polishes or waxes that could damage the finish. Mild soap may be used for cleaning.
FAQ
- Q: Can this Bull Bar fit other vehicle models?
- A: This Bull Bar is specifically designed for 2022-2024 Toyota Tundra and may not fit other vehicle models.
- Q: Is professional installation recommended?
- A: While the installation instructions are provided, professional installation is recommended for optimal results and safety.
PARTS LIST
| 1 | Bull Bar | 6 | 10mm x 35mm Hex Bolts |
|---|---|---|---|
| 1 | Driver/Left Mounting Bracket | 14 | 10mm x 30mm OD x 2.5mm Flat Washers |
| 1 | Passenger/Right Mounting Bracket | 8 | 10mm Lock Washers |
| 1 | Driver/Left Support Bracket | 8 | 10mm Hex Nuts |
| 1 | Passenger/Right Support Bracket | 2 | 10mm Fish Wires |
| 2 | 10mm x 35mm Bolt Plates |
PROCEDURE
Installation Instructions
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. INSTALLATION MAY INTERFERE WITH FRONT MOUNTED SENSORS
- Start installation under the Passenger/Right front side of the vehicle. Locate the end of the frame just behind the bumper and temporarily remove the (4) factory bolts, (Figure 1).
- Select the Passenger/Right Mounting Bracket. Reuse the factory bolts to attach the Mounting Bracket to the frame, (Figure 2). Do not tighten hardware.
- Repeat Step 1 to attach the Driver/Left Mounting Bracket.
- Select the Bull Bar. Attach the Bull Bar to the (2) Mounting Brackets with (4) 10mm Hex Bolts, (8) 10mm Flat Washers, (4) 10mm Lock Washers and (4) 10mm Hex Nuts, (Figures 3 & 4). Do not tighten hardware.
- Select (1) 10mm Bolt Plates and (1) 10mm Fish Wire. Thread the Fish Wire onto the Bolt Plate, (Figure 5). Insert the end of the Fish Wire into the large hole and guide the Bolt Plate though to the smaller hole towards the side of the vehicle, (Figures 6 & 7).
- Select the Passenger/Right Support Bracket. Attach the Support Bracket to the Bolt Plate with (1) 10mm Flat Washer, (1) 10mm Lock Washer and (1) 10mm Hex Nut, (Figure 8). Attach the Support Bracket to the Mounting Bracket with (1) 10mm Hex Bolt, (2) 10mm Flat Washers, (1) 10mm lock washer, and (1) 10mm Hex Nut, (Figures 9 & 10). Do not tighten hardware.
- Repeat Steps 5 & 6 to attach the Driver/Left Support Bracket to the frame and Mounting Bracket.
- Level and adjust the Bull Bar, then tighten all hardware.
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
Passenger/Right Side Installation Pictured
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>