TAC 4S-F1122-1N 4 Inch Oval Straight Sidebars Installation Guide
- June 1, 2024
- TAC
Table of Contents
TAC 4S-F1122-1N 4 Inch Oval Straight Sidebars
Product Specifications
- Product Name: 4-Inch Oval Straight Sidebars
- Compatible Vehicle Models: 2015-2024 F150 SuperCrew Cab, 2022-2024 F150 Lightning EV SuperCrew Cab, 2017-2024 F250/350/450/550 Super Duty Crew Cab
- Part Number: 4S-F1122-1N
- Manufacturer Website: www.tacautoparts.com
Product Usage Instructions
- Remove all contents from the box and verify that all parts are present.
- Start the installation under the Driver/Left side of the vehicle.
- Prepare the factory mounting location by removing excess paint and undercoating from the studs using a wire brush or thread chaser die.
- Slide a Plastic Washer over each factory mounting stud to prevent corrosion.
- Attach Support Brackets and Front Mounting Brackets to the designated locations using Flat Washers and Nylon Lock Nuts. Do not tighten hardware yet.
- Repeat the process for Center/Rear Mounting Brackets and Support Brackets.
- Attach the driver/left Sidebar to the Mounting Brackets using Combo Bolts. Do not tighten hardware yet.
- Level and adjust the Sidebar, then tighten all hardware.
- Repeat the above steps to attach the passenger/right Sidebar.
- Regularly inspect the installation to ensure all hardware remains secure and tight.
Frequently Asked Questions
Q: How do I clean the Sidebars?
A: To clean the Sidebars, use only mild soap and avoid using any polish or wax containing abrasives that could damage the finish.
Q: Do I need assistance for installation?
A: While not required, it is recommended to have assistance during installation for safety and ease of installation.
Q: What if some parts are missing from the box?
A: If any parts are missing, please contact the manufacturer’s website at www.tacautoparts.com for assistance in obtaining replacement parts.
4INCH OVAL STRAIGHT SIDEBARS
2015-24 F150 SUPERCREW CAB
2022-2024 F150 LIGHTNING EV SUPERCREW CAB 17-24 F250/350/450/550 SUPER DUTY
CREW CAB
PART# 4S-F1122-1N
PARTS LIST
INSTALLATION INSTRUCTIONS
PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY. ASSISTANCE IS RECOMMENDED.
- Start the installation under the Driver/Left side of the vehicle. Locate the front factory mounting location along the inner side of the body, (Figure 1). Use a wire brush or thread chaser die to remove excess paint and/or undercoating from all studs.
- Slide (1) Plastic Washer over each of the (3) factory mounting studs in the body panel, (Figures 2—3). IMPORTANT: The Plastic Washers are designed to prevent corrosion between the aluminum body panel and the steel mounting brackets. Do not install the Brackets without the Plastic Washers.
- Select (1) Support Bracket, (Figure 4). Attach the Bracket to the (2) studs on the pinch trim with (2) 8mm Flat Washers and (2) 8mm Nylon Lock Nuts, (Figures 4 & 5). Do not tighten hardware.
- Select (1) Front Mounting Bracket, (Figure 6). Attach the Bracket to the upper stud in the rocker panel and Support Bracket with (2) 8mm Flat Washers, and (2) 8mm Nylon Lock Nuts, (Figure 6). Do not tighten hardware.
- Repeat Steps 3 & 4 to attach (2) Center/Rear Mounting Brackets and (2) Support Brackets to the center and rear mounting location.
- Select the Driver/Left Sidebar. Attach the Sidebar to the (3) Mounting Brackets with (6) 8mm Combo Bolts, (Figure 7). Do not tighten hardware.
- Level and adjust the Sidebar, then tighten all hardware.
- Repeat Steps 1—7 to attach the Passenger/Right Sidebar.
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Use only mild soap to clean the Sidebar.
Driver/Left Side Installation Pictured
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>