TAC 3B-N1132 Bull Bar Instruction Manual
- June 1, 2024
- TAC
Table of Contents
TAC 3B-N1132 Bull Bar
Specifications
- Product: Bull Bar
- Vehicle Compatibility: 2022-2024 Nissan Frontier
- Part Number: 3B-N1132
- Website: www.tacautoparts.com
Product Usage Instructions
Installation Instructions
- Remove contents from the box and verify all parts are present.
- Read the instructions carefully before starting the installation. Note that minor cutting may be required, and assistance is recommended.
- Installation may interfere with front sensor operation.
- Remove the driver/left factory tow hook if equipped.
- Select the driver/left side Frame Mounting Bracket and attach it to the tow hook.
- Hold the splash guard in place against the bottom of the Brackets, mark the Bracket location onto the splash guard, and cut slots out of the splash guard to clear the Brackets.
- Reinstall the splash guard.
- Do periodic inspections to ensure that all hardware is secure and tight.
Maintenance Instructions
To protect your investment, wax the Bull Bar after installing. Regular waxing is recommended to add a protective layer over the finish. Avoid using polish or wax-containing abrasives that could damage the finish. Mild soap can be used to clean the Bull Bar.
PARTS LIST
- 1 Bull Bar
- 1 Driver/Left Side Frame Bracket
- 1 Passenger/Right Side Frame Bracket
- 4 12-1.25mm x 45mm Special Fine Thread Hex Bolts
- 4 12-1.75mm x 35mm Coarse Thread Hex Bolts
- 12 12mm x 37mm x 3mm Flat Washer
- 8 12mm Lock Washer
- 4 12mm Hex Nuts
PROCEDURE
REMOVE CONTENTS FROM THE BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. MINOR CUTTING MAY BE REQUIRED. ASSISTANCE IS RECOMMENDED. INSTALLATION MAY INTERFERE WITH FRONT SENSOR OPERATION.
-
Determine if the vehicle is equipped with a lower splash guard, (Figure 1). Models with splash guard.
- a. Start installation from the driver/left wheel opening. Remove the hardware attaching the inner fender liner to the edge of the fender, (Figure 2). Remove the screws attaching the end of the lower splash guard to the bottom of the fender, (Figure 3).
- b. Repeat the previous Step to release the passenger/right end of the splash guard.
- c. Continue across the bottom of the vehicle and remove the rest of the hardware to remove the splash guard, (Figures 1 & 4). Models without splash guard. (Pro 4X model for example-see Figure 5). Skip to Step 2.
-
Remove the driver/left factory tow hook, if equipped, (Figures 1 & 5).
-
Select the driver/left side Frame Mounting Bracket, (Figure 6). Attach the Bracket to the tow hook\ location on the bottom of the frame channel with the included (2) 12mm x 45mm Fine Thread Hex Bolts, (2) 12mm Lock Washers and (2) 12mm Flat Washers, (Figures 6 & 7).
NOTE : For models with tow hooks, reinstall the tow hook with the Bracket between the tow hook and frame. Do not fully tighten the hardware. -
Repeat Steps 2 & 3 for the passenger/right side Mounting Bracket installation.
-
Carefully unwrap the Bull Bar.
-
With assistance, hold the Bull Bar up to the outside of the Brackets. Attach the Bull Bar to the Brackets with the included (4) 12mm x 35mm Coarse Thread Hex Bolts, (8) 12mm Flat Washers, (4) 12mm Lock Washers and (4) 12mm Hex Nuts, (Figures 8 & 9).
-
Level and adjust the Bull Bar properly and tighten all hardware. Models with splash guard only:
- a. Hold the splash guard up in place against the bottom of the Brackets. Mark the Bracket location onto the splash guard, (Figure 10). Use a knife or hacksaw blade to cut slots out of the splash guard to clear the Brackets, (Figure 11).
- b. Reinstall splash guard.
-
Do periodic inspections of the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installation. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Bull Bar.
Driver/left Side Installation Pictured
FAQ
- Q: What should I do if I encounter difficulties during installation?
- A: If you encounter difficulties during installation, it is recommended to seek assistance from a professional or contact customer support for guidance.
- Q: Can the Bull Bar be used on other vehicle models?
- A: The Bull Bar is specifically designed for use with 2022-2024 Nissan Frontier models. It is not recommended for use on other vehicle models.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>