TAC 3B-19C100T Bull Bar Instruction Manual

TAC 3B-19C100T Bull Bar

Specifications

• Product: Bull Bar
• Compatibility: 2019-2024 Chevy Silverado 1500
• Part Number: 3B-19C100T

Product Usage Instructions

Installation:

1. Identify the parts included in the package.
2. Refer to the provided manual for step-by-step installation instructions.
3. Ensure all hardware is securely fastened during installation.

Maintenance:

Regular maintenance is essential to protect your investment:

• Wax the product after installing to add a protective layer over the finish.
• Use aluminum polish for stainless steel to polish small scratches and scuffs.
• Clean the Bull Bar with mild soap. Avoid using abrasive polishes or waxes.

FAQ

• Q: How often should I inspect the installation?
  • A: Periodic inspections should be done to ensure all hardware is secure and tight.
• Q: How should I clean the Bull Bar for different finishes?
  • A: Use mild soap to clean the Bull Bar. For stainless steel, aluminum polish can be used for small scratches and scuffs. Avoid abrasive polishes or waxes.

PARTS LIST

PROCEDURE

REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. CUTTING MAY BE REQUIRED. INSTALLATION MAY INTERFERE WITH FRONT MOUNTED SENSORS. NOTE: It may be necessary to remove/relocate front license plate and license plate bracket. It is not required, but strongly recommended. If local/state law requires a front license plate, license plate relocation kit is available.

1. Start installation from under the front of the vehicle. Determine if the vehicle is equipped with tow hooks.
   IMPORTANT: Tow hooks cannot be reinstalled with the Bull Bar.
   Tow Hook equipped vehicles:

   • a. Remove the factory tow hook from the end of each frame channel, (Figures 1—3).

   • b. Select the passenger/right Mounting Bracket. Insert the Bracket through the opening in the bumper and up to the frame. Trim the plastic as required to clear the Bracket, (Figure 5). Repeat to check for clearance on driver/left side of bumper.

   • c. Proceed to Step 2.
     Vehicles without tow hooks:

   • a. Cut out the indented area in both sides of the plastic bumper insert to clear the Brackets as pictured, (Figures 4 & 5). IMPORTANT: Make several small cuts for best fit.

   • b. Check for clearance between Brackets and opening and trim the plastic as required to clear the Brackets.

2. Line up the holes in the Bracket with the holes in the end of the frame channel for the tow hook, (Figure 5). Select (1) 12mm Double Bolt Plate, (Figure 6). Insert the Bolt Plate into the end of the frame and out through the (2) holes in the side of the frame and out through the Bracket, (Figures 6 & 8). Secure the Bracket to the Bolt Plate with (2) 12mm Flat Washers and (2) 12mm Nylon Lock Nuts. Leave hardware loose at this time.

3.  Repeat Step 2 to install the 12mm x 35mm Single Bolt Plate, (Figure 9), into the single forward tow hook mounting hole in the other side of the frame channel and Bracket, (Figures 6, 10 & 11).

4. Repeat Steps 2 & 3 to install the driver/left Mounting Bracket.

5. With assistance, hold the Bull Bar up in position on the outside of the Mounting Brackets. Attach the Bull Bar to the Brackets with (4) 10mm x 30mm Hex Bolts, (8) 10mm Flat Washers and (4) 10mm Nylon Lock Nuts, (Figures 12 & 13). Do not tighten hardware at this time.

6. Check the Bull Bar alignment with the vehicle and for clearance between the Bull Bar and the bumper. Adjust as required then fully tighten all hardware at this time.

7. Do periodic inspections to the installation to make sure that all hardware is secure and tight. To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish. For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be used also to clean the Bull Bar.
   For gloss black finishes: Mild soap may be used to clean the Bull Bar

Installation Instruction

Passenger/right Side Installation Pictured

• www.tacautoparts.com

References

• TACUSA
• TACUSA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>