PHILIPS MG5910-28 Versatile Trimmer Instruction Manual

PHILIPS MG5910-28 Versatile Trimmer

Specifications

• USB power source: 5V, 1A output rating
• IPX4 (splash-proof) power source recommended for moist environments
• Manufacturer: Philips
• Website: www.philips.com/support
• Contact: 1-866-800-9311

FAQ

Frequently Asked Questions

• Q: Can I charge the product with any USB power source?
  • A: No, it is recommended to only use a certified USB power source with an output rating of 5V, 1A to avoid hazards.
• Q: Is the product safe for use in the bath or shower?
  • A: Yes, the appliance is waterproof and suitable for use in the bath or shower.
• Q: What should I do if the product becomes abnormally hot during use?
  • A: Stop using the product immediately and contact Philips for assistance.

IMPORTANT SAFETY INSTRUCTIONS

When using an electric product, basic precautions should always be followed, including the following: Read all instructions before using this product.

DANGER: To reduce the risk of electric shock:

• To charge the product, only use a USB power source on a certified product with output rating 5 V, ≥ 1 A. For safe charging in a moist environment (e.g. in a bathroom), only use an IPX4 (splash-proof) power source. A suitable power source (e.g. Philips HQ87) is available via www.philips.com/support. If you need support finding the correct USB power source, contact Philips support at 1-866-800-9311. Using a non-certified USB power source may cause hazards or serious injuries.
• Keep the USB cable and the USB power source dry.
• Do not reach for a corded product that has fallen into water. Unplug immediately from the power outlet.
• Do not place or store the product where it can fall or be pulled into a tub or sink. Do not place or drop the product into water or other liquid.
• This product does not work while it is connected to the power outlet. Except when charging, always unplug this product from the power outlet.
• Remove USB power source from power outlet and product before cleaning the product with water.

WARNING

To reduce the risk of burns, fire, electric shock, or injury to persons:

• This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the product by a person responsible for their safety. Children should be supervised to ensure that they do not play with the product.
• Use this product only for its intended household use as described in this manual. Misuse can lead to hazards or serious injuries. Do not use attachments not recommended by Philips Electronics Ltd (Canada).
• Never operate this product if it has a damaged USB power source, if it is not working properly, after it has been dropped or damaged, or after the product or the USB power source has been dropped into water. For assistance call 1- 866-800-9311.
• Keep the USB cable and the USB power source away from heated surfaces.
• Never drop or insert any object into any opening.
• Do not use the USB power source in or near a power outlet that contains an electric air freshener to prevent damage to the USB power source.
• Do not use product outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
• Always check cutting units and other attachments and accessories before you use the product. Never use the product with a damaged cutting unit, attachment or accessory, as injury may occur.
• Always attach the USB cable to the USB power source and the product first, then attach the USB power source to the power outlet. To disconnect, set all controls to ‘off’ position. Then remove the USB power source from the power outlet.
• Plug USB power source directly into power outlet. Do not use an extension cord.
• Unplug USB power source before plugging in or unplugging the product.
• The batteries used in this product may present a fire or chemical burn hazard if mistreated. Do not disassemble, heat above 100 °C (212 °F) or incinerate.
• Only use original Philips accessories or consumables.
• Charge, use and store the product at a temperature between 5 °C and 35 °C.
• Keep product and batteries away from fire and do not expose them to direct sunlight or high temperatures.
• If the product becomes abnormally hot or smelly, changes color or if charging takes longer than usual, stop using and charging the product and contact Philips.
• Do not place products and their batteries in microwave ovens or on induction cookers.
• Do not open, modify, pierce, damage or dismantle the product or battery to prevent batteries from heating up or releasing toxic or hazardous substances. Do not short-circuit, overcharge or reverse charge batteries.
• If batteries are damaged or leaking, avoid contact with the skin or eyes. If this occurs, immediately rinse well with water and seek medical care.
• When you handle batteries, make sure that your hands, the product and the batteries are dry.
• To avoid accidental short-circuiting of batteries after removal, do not let battery terminals come into contact with metal objects (e.g. coins, hairpins, rings). Do not wrap batteries in aluminum foil. Tape battery terminals or put batteries in a plastic bag before you discard them.

Electromagnetic fields (EMF)

• This Philips appliance complies with all applicable standards and regulations regarding exposure to electromagnetic fields.

SAVE THESE INSTRUCTIONS

IMPORTANT INFORMATION

• This appliance is waterproof. It is suitable for use in the bath or shower and for cleaning under the tap.
• Because of hygiene, only one person should use the appliance.
• Switch off the appliance before removing or attaching attachments and before cleaning.
• Clean the appliance after each use (see ‘Cleaning’).
• Only use cold or lukewarm water to clean the appliance.
• Never use compressed air, scouring pads, abrasive cleaning agents or aggressive liquids such as gasoline or acetone to clean the appliance.
• Caution: Never dry the trimmer teeth with a towel or tissue, as this may damage the trimmer teeth.

Introduction

Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome.

You can find the model number on the back of your product.
The full model number (e.g. MG1234/56) is located on the bottom of the packaging, your receipt or order confirmation.

Features (Fig. 1)

1. Extra-wide hair trimmer
2. Precision trimmer
3. Nose and ear hair trimmer
4. Full-size hair trimmer
5. On/off button
6. Battery status indicator
7. Socket for small plug
8. USB cable
   • Note: A suitable power source (e.g. Philips HQ87) is available via www.philips.com/support.
9. Stubble comb 1 mm
10. Stubble comb 2 mm
11. Beard comb 3 mm
12. Beard comb 5 mm
13. Beard comb 7 mm
14. Hair comb 4 mm
15. Hair comb 9 mm
16. Hair comb 12 mm
17. Hair comb 16 mm
18. Fading hair guard 4 mm – 9 mm
19. Fading hair comb 4 mm – 9 mm
20. Body comb 3 mm
21. Body comb 5 mm

Not shown: cleaning brush and pouch

Charging

• Charging or using the appliance at temperatures below 5 °C or higher than 35 °C adversely affects the lifespan of the battery.
• If the appliance is subjected to a major change in temperature, pressure or humidity, let the appliance acclimatize for 30 minutes before use.

Charge the appliance before first use and when the battery status indicator shows that the battery is almost empty. When the appliance has charged for 70 minutes, it has a cordless operating time of up to 180 minutes.

Warning: Keep the USB cable and the USB power source dry.

1. Make sure that the appliance is switched off.
2. Insert the small plug of the USB cable into the socket in the bottom of the appliance (Fig. 2).
3. Insert the USB plug into the USB power source (not included) (Fig. 3).
4. Insert the USB power source into the power outlet (Fig. 4).
5. After charging, remove the USB power source from the power outlet and pull the small plug out of the appliance.

Quick charge

After approx. 5 minutes of charging, the appliance contains enough power for one cordless trimming session.

Battery status indications

Note: Approx. 30 minutes after the battery is fully charged, the battery status indicator switches off automatically.

Using the appliance

Trimming tips

• When trimming for the first time, start by using the comb with the maximum trimming length setting to familiarize yourself with the appliance.
• Since all hairs do not grow in the same direction, you may want to try different trimming directions (i.e. upwards, downwards, or across). Practice is best for optimum results.
• Always make smooth and gentle movements and be sure the surface of the comb always stays in contact with your skin.
• For best results, use the appliance on clean, dry hair, as wet hair tends to stick to the body.
• When too many hairs have accumulated on the appliance, remove the hairs before and/or during use, for best trimming results (see ‘Cleaning’).

Detaching and attaching cutting elements

1. To detach a cutting element, place your finger near the teeth of the cutting element and push gently upwards until the cutting element is released from the handle (Fig. 5).
2. To attach a cutting element, insert the plastic notch at the back of the cutting element into the guiding slot in the handle and gently press the teeth of the cutting element downwards until they click into place (Fig. 6).

Detaching the nose and ear hair trimmer

1. Place your finger on the recess at the back of the attachment and push the attachment off the handle (Fig. 7). Use your other hand to prevent the attachment from dropping on the floor.

Attaching and detaching combs

1. To attach any type of comb onto a cutting element, slide the front part of the comb onto the teeth and press the notch at the back of the comb downwards until it clicks into place (Fig. 8).
2. To detach any type of comb from the cutting element, carefully push its back part off the appliance and then slide it off the cutting element (Fig. 9).

Comb colors

The combs provided with the appliance have different colors depending on their intended use. Select the type of comb suitable for the part of the body that you want to trim.

Switching the appliance on and off

• To switch the appliance on or off, press the on/off button once (Fig. 10).

Attachments for use on beard

• Always comb your beard or moustache with a fine comb before you start trimming.

Full-size hair trimmer

Use the full-size hair trimmer without a comb to trim hair close to the skin (to a length of approx. 0.5 mm) or to create clean lines around your beard, neck and sideburns.

1. To trim hair close to the skin, place the flat side of the cutting element against your skin and make strokes against the direction of hair growth (Fig. 11).
2. For contouring, hold the cutting element perpendicular to the skin and move it upwards or downwards with gentle pressure (Fig. 12).

Beard combs

Attach a black beard comb to the full-size hair trimmer to trim your beard and moustache evenly to the desired length. The appliance comes with 5 black beard combs. The numbers on the combs relate to the number of millimeters of hair length that will remain after trimming.

1. Attach a beard comb to the full-size hair trimmer.
2. To trim in the most effective way, move the comb against the direction of hair growth (Fig. 13). Make sure that the surface of the comb always stays in contact with the skin.

Attachments for use on head

• Always comb your hair before you start trimming.
• For best results, use the appliance on clean, dry hair.

Extra-wide hair trimmer

Use the extra-wide hair trimmer without a comb to trim the hair on your head very close to the skin (to a length of approx. 0.5 mm) or to contour the neckline and area around the ears.

1. To contour the hairline around the ears, comb the hair ends over the ears.
2. Tilt the appliance in such a way that only one edge of the cutter teeth touches the hair ends when you shape the contours around the ears.
3. To contour the nape of the neck or sideburns, turn the appliance and make downward strokes (Fig. 14).
4. Move the appliance slowly and smoothly following the natural hairline.

Hair combs

Attach a dark gray hair comb to the extra-wide hair trimmer to evenly trim the hairs on your head. The appliance comes with 4 hair combs. The numbers on the combs relate to the number of millimeters of hair length that will remain after trimming.

1. Attach a hair comb to the extra-wide trimmer.
2. Move the trimmer slowly over the crown from different directions to achieve an even result. Make sure that the surface of the comb always stays in contact with the skin.
3. Always move the trimmer against the direction of hair growth (Fig. 15). Press lightly.
4. Make overlapping passes over the head to ensure that all hair that should be cut has been cut.
5. Gently shake the hairs off the appliance in between strokes to prevent hairs from collecting between the cutting element and the comb.

Fading hair combs

Attach a dark gray fading hair comb to the extra-wide hair trimmer to create a fade line around the ears. The appliance comes with 2 fading hair combs. Use both combs to trim hair around both ears. Choose a comb based on the preferred trimming direction of back to front or front to back.

• Comb mm
  • Fading hair combs / 4 mm – 9 mm

1. Attach one fading hair comb to the extra-wide hair trimmer to trim the hair around the ear.
2. Place the trimmer on your hair close to the ear. Place the trimmer at the back or front of your ear, depending on the trimming direction you prefer. Always make sure that the side of the comb with the short teeth is closest to your ear (Fig. 16).
3. Move the trimmer slowly around the ear, while holding it steady.
4. Repeat the movement several times around one ear to make sure that all the hair that should be cut has been cut to a fade. Then attach the other fading hair comb to trim the hair around the other ear.
5. Gently shake the hairs off the appliance in between strokes to prevent hairs from collecting between the cutting element and the comb.

Attachments for use on body

Always use a body comb when trimming sensitive areas.

Body combs

Attach a light gray body comb to the full-size hair trimmer to trim hairs below the neckline. The appliance comes with 2 body combs. The numbers on the combs relate to the number of millimeters of hair length that will remain after trimming.

• Comb / mm
  • Body comb / 3 mm
  • Body comb / 5 mm

1. Attach a body comb to the full-size hair trimmer.
2. To trim in the most effective way, stretch the skin with your free hand and move the comb against the direction of hair growth (Fig. 17). Make sure that the surface of the comb always stays in contact with the skin.

Precision attachments for use on the face

Precision trimmer

Use the precision trimmer to create fine lines and contours around your facial style close to the skin, to a length of approx. 0.5 mm.

1. Hold the precision trimming head perpendicular to the skin and move the trimming head upwards or downwards with gentle pressure (Fig. 18).

Nose and ear hair trimmer

Use the nose and ear hair trimmer to trim your nose and/or ear hair.

• Make sure nasal passages are clean. Make sure outer ear channels are clean and free from wax.
• Do not insert the cutting element too deep into your nostrils or ear channels (max. 5 mm).
• When trimming both nose and ear hair, make firm, rotary movements to ensure that the cutting element reaches all the hairs.
• Clean the nose and ear hair trimmer after each use
  • (see ‘Cleaning the nose and ear hair trimmer’).

Note: The nose and ear hair trimmer is not designed to clean-shave your nostrils or ear channels, but to cut the hairs to a shorter length. Nose and ear hairs have important protective functions and should not be fully removed.

Trimming nose hair

1. Gently insert the cutting element into one of the nostrils. Move the tip in and out of the nostril in a firm, rotary motion to cut the hairs to a shorter length (Fig. 19).

Trimming ear hair

1. Slowly move the cutting element along the outer ear to trim hairs that stick out beyond the rim.
2. Gently insert the cutting element into the outer ear channel. Move the tip in and out of the outer ear channel in a firm, rotary motion to cut the hairs to a shorter length (Fig. 19).

Cleaning

After every use: cleaning under the tap

1. Make sure that the appliance is switched off and that the USB power source has been removed from the power outlet and from the appliance.
2. Remove any comb (see ‘Attaching and detaching combs’) and cutting element (see ‘Detaching and attaching cutting elements’) from the appliance.
3. Rinse the hair chamber under running tap water (Fig. 20).
4. Clean the cutting element and comb under running tap water (Fig. 21).
5. Carefully shake off excess water and let all parts air-dry completely.

Thorough cleaning

1. Make sure that the appliance is switched off and that the USB power source has been removed from the power outlet and from the appliance.
2. Clean the handle under the tap or wipe the handle clean with a dry or moist cloth.
3. Remove any comb (see ‘Attaching and detaching combs’) or cutting element (see ‘Detaching and attaching cutting elements’) from the appliance.
4. Remove any hairs that have accumulated in the hair chamber with the cleaning brush supplied.
5. Remove any hairs that have accumulated in the cutting elements and/or combs with the cleaning brush supplied.
6. Clean the cutting element and comb under running tap water (Fig. 21).
7. Rinse the cutting elements and combs under running tap water (Fig. 21).
8. Carefully shake off excess water and let all parts air-dry completely.

Cleaning the nose and ear hair trimmer

Clean the nose and ear hair trimmer immediately after use and when a lot of hair or dirt has accumulated on the cutting element.

1. Rinse the nose and ear hair trimmer head under running tap water (Fig. 22).
2. Switch on the appliance and rinse the cutting element once more to remove any remaining hairs. Then switch off the appliance again. If a lot of hair or dirt accumulates on the cutting element, this can hinder or decrease the performance of the nose and ear hair trimmer. For a thorough clean, detach the nose and ear hair trimmer head from the appliance and immerse it in a bowl with warm water for a few minutes to soak and soften the debris. Reattach the nose and ear trimmer head and switch on the appliance to rinse off stubborn hair/debris.
3. Carefully shake off excess water and let all parts air-dry completely.

Storage

Note: Do not place or store the appliance where it can fall or be pulled into a tub or sink, water or other liquid while plugged in.

• Make sure that the appliance is switched off and that the USB power source has been removed from the power outlet and from the appliance.
• Do not wrap the USB cable around the appliance when storing.
• Store the appliance, the USB power source and all the accessories in the pouch supplied. Place the pouch in a safe, dry location, where it will not be crushed, banged, or subject to damage.
• Make sure that the appliance and the accessories are dry before you store them in the pouch.

Ordering Accessories And Disposal

Ordering accessories

• To buy accessories or spare parts, visit www.philips.com/parts-and-accessories or go to your Philips dealer.
• You can also contact the Philips Consumer Care Center in your country (see the international warranty leaflet for contact details).

Disposal

• This product contains a rechargeable lithium-ion battery which must be disposed of properly.
• Contact your local town or city officials for battery disposal information. You can also call 1-888-224-9764 or visit www.call2recycle.ca for battery drop-off locations.
• For assistance, visit our website www.philips.com/support or call 1-866-800-9311 toll free.
• Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. For recycling information, please contact your local waste management facilities or visit www.recycle.philips.com.

Support

• For all product support such as frequently asked questions, please visit www.philips.com/support.

Warranty

Full Four-Year Warranty

Philips Electronics Ltd warrants this new product against defects in materials or workmanship for a period of four years from the date of purchase, and agree to repair or replace any defective product without charge.

IMPORTANT: This warranty does not cover damage resulting from accident, misuse or abuse, lack of reasonable care, the affixing of any attachment not provided with the product or loss of parts or subjecting the product to any but the specified voltage.*

NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Cutting units and combs are not covered by the terms of this warranty because they are subject to wear and tear.

In order to obtain warranty service, simply go to www.philips.com/support for assistance. It is suggested that for your protection you return shipments of product by insured mail, insurance prepaid. Damage occurring during shipment is not covered by this warranty.

NOTE: No other warranty, written or oral, is authorized by Philips Electronics Ltd. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state, province to province or country to country. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion and limitations may not apply to you.
*Read enclosed instructions carefully.

© 2023 Koninklijke Philips N.V.
All rights reserved
3000.085.0830.1 (21/11/2023)

References

• Parts & accessories | Philips
• Support Home | Philips
• Login

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>