VORTEXGEAR VTK-8000 Vortex New Race 3 Mechanical Keyboard User Guide
- June 1, 2024
- VORTEXGEAR
Table of Contents
VORTEXGEAR VTK-8000 Vortex New Race 3 Mechanical Keyboard
Connection
Bluetooth / USB / 2.4Ghz
Turn on the power switch, then press and hold Fn + 2 / 3 / 4 for three seconds to enter pairing mode. The device will display ‘Model M#1 /2/3’ and once confirmed, the pairing is complete. During this process, the LED indicator lights (Bluetooth device 1: red light/ Bluetooth device 2: green light/ Bluetooth device 3: blue light) will flash sequentially.
Macro instructions
(support Bluetooth mode macro)
- Fn + R_Shift selects the editing layer (three layers in total). The LED indicator lights on top will respectively show (first layer: red light/ second layer: green light/ third layer: blue light).
- Fn + Ins (Absolute position) enters editing mode with a steady yellow light.
- Choose the key to edit, and the indicator light for that layer will start flashing.
- Input the content, and the indicator light for that layer will flash (each key edit can hold up to 32 keys).
- Fn + Enter (Absolute position) confirms the input, and the indicator light for that layer will remain steady again.
- Fn + Ins (Absolute position) exits editing mode, and the yellow light turns off.
- Battery ‘ AA/ 1.5V *2 (Alkaline battery
- Working Current : 9mA – Release the key for 5 seconds will enter into standby mode
- Standby Current ‘ 3.5mA – Standby for 5 seconds will enter into hibernation mode
- Hibernation Current : 3mA – Hibernate for 30 minutes will enter into sleep mode
- Sleep Current: 0.7mA (Bluetooth will be disconnected)
- Rated Input Power ‘ 5V”‘ 500mA
LED Indicator Light
- Product Name : Mechanical Keyboard
- Model Name : VTK-8000
- Product Size : L W'”H : 38.516.5*3.5 cm ± 0.3
Fn switch
Press and hold Fn while simultaneously holding Caps Lock, L_Ctrl, and R_Win to
enter the Fn setting mode (LED indicator lights on top will flash white). The
first key pressed in this mode is the Fn key.
(Ins/ Enter/ Shift cannot be used as Fn, and Fn layer cannot be used for
macro)
Fn Key Combos
TECHNICAL
SUPPORT[email protected]
CUSTOMER SERVICE
[email protected]
WEBSITE OFFICIAL www.vortexgear:store
FCC
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be u sed in portable exposure condition without restriction.