JBL 109WRLSMIC Wireless Microphone User Guide

JBL 109WRLSMIC Wireless Microphone

Product Information

The Harman Wireless Microphone is a device that allows for wireless microphoning. It operates on a no-interference, no-protection basis, which means that if the user seeks protection from other radio services operating in the same TV bands, a radio license is required. The device comes with a safety sheet that should be read carefully before use to ensure safe handling.

Battery Information

To protect battery lifespan, it is recommended to fully charge the device at least once every 3 months. The battery life will vary depending on usage patterns and environmental conditions. The speaker may experience noise interference when singing a song while charging the receiver.

Product Usage Instructions

1. Read the safety sheet carefully before using the device.
2. Charge the device fully before use.
3. Turn on the device by pressing the power button.
4. Ensure that the microphone is within range of the receiver.
5. Adjust the volume as needed using the volume controls.
6. To protect battery lifespan, fully charge the device at least once every 3 months.
7. If using the device in an area with other radio services operating in the same TV bands, a radio license may be required for protection.

Following these instructions will ensure proper usage and care of the Harman Wireless Microphone.

Before using this product, read the safety sheet carefully.

IN THE BOX

CHARGING

The speaker may have noise interference when singing a song while charging receiver
To protect battery lifespan, fully charge at least once every 3 months. Battery life will vary due to usage patterns, .ina environmental cond1,1ons

General specification

• Model No .. Wireless Microphone Set
• Distance between transmitter and receiver: > 10 m
• Polar pattern: Cardioid
• Frequency response: 65 Hz – 15 kHz
• 5ignal-to-Noise(S/N) ratio:> 60 dBA
• UHF frequency band: 470 960 MHz (depends on SKU) (EU 657 – 662 MHz)
• THD: < 0.5%, typical
• Transmitter transmitting power < 1 o mW, typical
• Receiver input: I /4″(6.3 mm) unbalanced
• Receiver maximum Output Level: 13 dBV, typical
• Receiver rechargeable Battery: Lithium-ion Polymer 3.7 WH (Equivalent to 3.7 V, 1000 mAh)
• Receiver charge time: <3.5 hours@5V/1 A
• Receiver battery Playtime: Up to 6 hours
• Microphone battery: 4 x AA alkaline (included)

Dimensions and Weight

• Dimensions (W x H x D):
  Microphone <DSO x 233 mm/ 1.95″x 9.16″;
  Receiver: 70 mm x BO mm x 20 mm I 2.75″x 3.14″x 0.78″

• Weight.
  Microphone: 247 g I 054 lb;
  Receiver 54g / 0.12 lb

Remark:
This device operates on a no-interference, no-protection basis. Should the user seek to obtain protection from other radio services operating in the same TV bands, a radio licence is required. For further details, consult Innovation, Science and Economic Development Canada’s Client Procedures Circular CPC-2-1-28, Voluntary Licensing of Licence-Exempt Wireless Microphones in the TV Bands.

Canada.
Types of antennas:
Spring antenna, maximum PK gain : -4.15 dBi
America:
6A: 657.027 MHz – 659.027 MHz 6B: 659.427 MHz – 661.427 MHz
Europe:
6A: 657.027 MHz – 659.027 MHz 6B: 659.427 MHz – 661.427 MHz

Safety Instruction and Warranty Card

PRODUCT REGISTRATION
registerjbl.com

SIGN UP & STAY TUNED
Register your product
Product registration may not be available for all countries
Download the full warranty Card and safety information and other helpful information from our website: www.jbl.com/warrantyandsafetybooks

IMPORTANT SAFETY INSTRUCTIONS

For all products:

1. Read these instructions
2. Keep these instructions
3. Heed all warnings
4. Follow all instructions
5. Clean only with a dry doth.
6. Do not block any ventilation openings Install this apparatus in accordance with the manufacturer’s instructions
7. Do not install these apparatus near any heat. sources such as radiator heat registers, stoves or other apparatus including amplifiers) that produce heat
8. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarised plug has two blades with one wider thaa the other A grounding-type plug has two blades and a third grounding prong The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet
9. Protect the power cord from being walked on or pinched, particularly t plugs, cover sincere receptacles, and the point where they EDT from the apparatus 10.
10. Use any attachments or accessories specified by the manufacturer.
11. Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus When it is used, be cautious when moving the cart/apparatus combination to avoid injury from tip-ovet
12. Unplug this apparatus during lightning storms or when unused for long periods of time
13. Refer al servicing to qualified service personnel, Servidng is required when the apparatus has been damaged in any way, such as when the power-upply cord or plag is damaged, liquid has been spilled or objects have fallen into the apparatus, or the apparatus has bees exposed to rain or moisture, does not operate normally or has been dropped
14. Todiscnnnect this apparatus from the AC mains completely, disconnect the power-supply cord plug from the AC receptacle
15. The mains plug of the power-supply cord shall remain readily operable.
16. This apparatus is intended to be used only with the power supply and/ar charging cable provided by the manufacturer

The following instructions may not apply to waterproof devices. Refer to your device user manual or quidk start guide for more waterproof instruction if any.

• Do not use this apparatus near water
• Do not expose this apparatus to dripping or splashing, and ensure that no objects filled with liquid’s, such as vases, are placed on the apparatus

WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE

CAUTION

FCC AND IC STATEMENT FOR USERS

(USA AND CANADA ONLY)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

• (1) This device may not cause harmful interference, and
• (2) this device must acept any interference received, induding interference that may cause undesired operation. CAN ICES-3(B)/NMB-348)

FCC SDOC SUPPLIER’S DECLARATION OF CONFORMITY HARMAN
Intenational hereby decdares that this equipment is in compliance with the FCC Part 15 Subpart B The declaration of conformity may be consulted in the support section of our Web site, accessible from www.jbl.com

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits fora Class B digital device, pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, ifnot installed and used in accordance with the instructions, may cause harmful interference to radio communications However, there is no guarantee that interference will not occur in a particular installation. f this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Inease the separation between the equipment and receiver.
• Connect the equipment into an outlet on a fruit different from that to which the recelver is connected
• Consult the dealer or an experienced radio/TV technician for help

Caution: Changes or modifications not expressly approved by HARMAN Could void the user’s authority to operate the equipment.

For Products That Transmit RF Energy:
FCC AND IC INFORMATION FOR USERS This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

FCCAC Radiation Exposure Statement
This equipment. complies with FCC and 1SED radiation exposure limits set forth for an uncontrolled environment.
In case this equipment has to subject to FCCAC SAR (Spedific Absorption Rate) exposure test, this equipment is designed to meet the requirements for exposure to radio waves established by the FCC and ISED. These requirements set a SAR limit of 1.6W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certifcation for use when properly wom on the body or on the head, with no separation. To meet RF exposure guidelines and reduce exposure to RF energy during the operation, this equipment should be positioned at least this distance away from the body or the head.

For radio equipment operates in 5150-5850MHz
FCC and IC Caution High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands These radar stations can cause interference with and/or damage to LE LAN (Licence-Exempt Looal Area Network) devices. No configuration controls are provided for this wireless equipment allowing any change in the frequency of operations outside the FCC grant of authorization for US operation according to Part 15.407 of the FCC rules

IC Caution: User should also be advised that:
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satelite systems;

• the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the size. limit: and
• The maximum antenna gain permitted for devices in the band 5725 S825 MHz shall comply with the trip. limits specified for point-to-point and non-point-to-point operation as appropriate

Use Restriction Attention in European Union, the operation is limited to indoor use within the band 5150-5350 MHz

Correct disposal of this product (Waste Electrical & Electronic Equipment)This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection fadility for recydling. Proper disposal and recyding helps protect natural resources, human health and the environment. For more information on disposal and recyding of this product, contact your local municipality disposal service, or the shop where you bought this product.

This product is RoHS compliant.
This product complies with Directive 2011/65/EU, and its amendments, on the restriction of the use of certain hazardous substances in electrical and electronic equipment REACH REACH (Regulation No 1907/2006) addresses the production and use of chemical substances and their potential impacts on human health and the environment.Artide 33(1) of REACH Regulation requires suppliers to inform the recipient if an artiste contains more than 0.16 (per weight per ride) of any substances) on the Substances of Very High Concem (SVH) Candidate List (REACH candidate list’). This product contains the substance “lead'(CAS- Na.7439-92-1) in a concentration of more than 0.19% per weight At the time of the release of this product, except for the lead substance, no other substances of

REACH
candidate list are contained in a concentration of more than 0.1% per weight in this product Note: On June 27, 2018, lead was added to the REACH candidate list The indusion of lead in the REACH candidate list does not mean that lead- containing materials pose an immediate risk or results in a restriction of permissibility of its use.

For devices with headphone jacks
WARNINGS / CAUTIONS

• Do NOT use the headphones at a high volume for any extended period
• To avoid hearing damage, use your headphones at a comfortable, moderate volume level.
• Turn the volume down on your device before placing the headphones on your ears, then tum the volume up gradually until you reach a comfortable listening level

For Products That Indude Batteries

Instructions for Users on Removal, Recycling, and Disposal of Used Batteries
To remove the batteries from your equipment or remote control, reverse the procedure described in the owner’s manual for inserting batteries. For products with a built-in battery that lasts for the lifetime of the product, removal may not be possible for the user.In this case, recycling or recovery centers handle the dismantling of the product and the removal of the battery. (, for any reason, it becomes necessary to replace such a battery, this procedure must be performed by authorized service centers In the European Union and other locations, it is illegal to dispose of any battery with household trash. All batteries must be disposed of in an environmentally sound manner Contact your local waste-management officials for information regarding the environmentally sound collection, recycling, and disposal of used batteries.
WARNING: Danger of explosion if battery s incorrectly replaced. To reduce the risk of fire, explosion or leakage of flammable liquid/gas, don’t disassemble, rest, puncture, short external contacts, expose to temperature above 60 (140F), sunshine or like, expose to extremely low air pressure or dispose of in fre or water. Replace only with specific batteries. The symbol indicating ‘separate collection’ for all batteries and accumulators shall be the crossed-out wheeled bin shown below

WARNING-For Products Contain Coin/Button Cell Batteries
DO NOT INGEST BATTERY, OR CHEMICAL BURN HAZARDS. This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can Cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not dose securely stop using the product and keepit away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

For All Products with Wireless Operation:
HARMAN International hereby desires that this equipment complies with the essential requirements and other relevant provisions of Directive 2014/53/EU. The declaration of conformity may be consulted in the sup section of our Web site, accessible from www.jbl.com

HARMAN International industries, Incorporated. All rights reserved. JBL is a trademark of HARMAN International Industries, Incorporated, registered in the United States and/or other countries. Features, spedifications and appearance are subject to change without notice. www.jbl.com
HARMAN International industries, Incorporated 8500 Balboa Boulevard, Northridge, CA 91329 USA 516.255.4545 (USA only)

WARRANTY CARD
SET UP INFORMATION & PRODUCT REGISTRATION
Congratulations on the purchase of your new Product We have done our utmost to make your experience the best one possible. If you have?Jr,; questions when setting up your Product and would like some helpful hints, we recommend that you visit the reporting country-specific SlW(lt website for ‘J(: AX Product: www.jbl.com. There you will also find relevant contact information. If you cannot find the information you are looking for, please contact the vendor that sold the Product to you or contact the relevant JBL eu&omer support center by electronic mail or phone. We recommend that you register your Product via the relevant country-specific website for your Product Your registration will allow, us to inform you about updates for certain products. possible new offers and new Products and/or applications. Registering Is ea5)’; just follow the instructions on the relevant country- specific website for your Product.
NOTE: THIS LIMITED WARRANTY DOES NOT APPLY TO CONSUMERS IN THE EUROPEAN ECONOMIC AREA (EEA) MEMBER STATES AND THE RUSSIAN FEDERATION AS THEY ARE PROTECTED BY LOCAL CONSUMER LAW AND BENEFIT FROM LOCAL STATUTORY WARRANTIES

LIMITED WARRANTY
WHO IS PROTECTED BY THE WARRANTY
This limited warranty (the ‘Limited Warranty’) protects ~ the original end- user (‘you’ 0( “your’), is not transferable , and is applicable arty in the country (exclusion EEA member states, and the Russian Federation) in v.tlidl you original~ purchased yCH JBL Product (the ‘Produclj. Any attempt to transfer this warranty shall immediately make this warranty void.

LIMITED WARRANTY
HARMAN International Industries, Incorporated iHARMAN’) is the manufacturer and through its local subsidiary, warrants to you that the Product (rounding components provided with the product will be free from defects in workmanship and materials for ONE year from the date of retail l)lN’chase by you (the “Warranty Period”). DuirfJ the Warranty Period, the Product including components), will be repaired or replaced at HARMAN’s option, witl’OOl a charge for either parts or labor OR at HARMAN’s sole option, the price of the Product may be refunded, subject to depreciation based on your purcha5e price for the Product pro-rated CNe( the remaining balance of the Warranty Period My warranty service or replacement of parts will not extend the Warranty Period. This Limited Warranty does not CCNer defects which are a result of (1) damage caused by accident, unreasonable use or neglect (including the lack of reasonable and 11eces.5afY maintenance); (2) damage during shipment (claims must be presented to the carrier); (3) damage to, or deterioration of, any accessory or decorative SlKface; (4) damage resulting from failure to follow instructions contained in YOlX owner’s manual.01; (5) damage resulting from the performance of repairs by someone other ttm an authorized JBL service center; (6) deterioration of parts, the nature of which is to become worn or depleted with use, such as batteries and headphone ear pads. Furthermore. this Limited Warranty CCNers only actual defects within the Product itself, and does not cover the cost of installation or removal from a fixed installation, setup, or adjustments. claims based on misrepresentation by the seller, performance variations resulting from installation-related circumstances such as source quality or AC power, or Product modifications. any um on which the serial Im been effaced, modified or removed, or units used for other than home use. This Limited Warranty is valid only for JBL products purchased from an authorized dealer, Except to the extent expressly prohibited in your by applicable law, all implied warranties, including fitness for a partiaJlar purpose and merchantability are hereby excluded and in no event shall HARMIW or  HARMAN subsidiaries be liable for any indirect, direct, incidental, special or consequential loss or damages whatsoever Qnctuding, without limitation, other pecuniary loss) arising out of the use of or inability to use the Product, even anchor a HARMAN subsidiary has been advised of the possibility of such damages. To any extent that HARMAN cannot lawfully ~ disclaim implied Wcrnlflties under this Limited Warranty, all such implied warranties are limited in. ration to the duration of lhi5 Wdfralty. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or exclusions 0( limitations on the duration of implied warranties or conditions, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary by jurisdiction.

HOW TO OBTAIN WARRANTY SERVICE
Contact the dealer who sold you this Product, or contact JBL customer support using the contact information on the relevant country-specific support website for your Product to request warranty service. To validate your right to this Limited Warranty, you must provide the original sales invoice or other proof of ownership and date of purchase. Do not return your Product without prior authorization from the corresponding dealer or HARMAN. warranty repair of the HARMAN Product must be carried out by an authorized dealer or service center, Unauthorized warranty repair ~ll void the warranty and is performed at your sole risk. You are also welcome to consult the relevant country-specific HARMAN support website for your Product for helpful hints.

WHO PAYS FOR WHAT
This Limited ‘MYranty covers all expenses for labor and materials required for the repair OR replacement of the Product that is filled to be defective, and a reasonable return shipping charge within the country of repair. Please be sure to save the ~ shipping carton(s}, because a charge will be made for additional cartons/packaging .. You win be charged for the cost of a unit that is not in need of repair (including resulting shipping costs), or for necessary repairs not covered by this Limited Warranty. We sincerely ~ you for your expression of confidence in JBL. We wish you many years of listening pleasure.

References

• ltc.in
• Anatel — Agência Nacional de Telecomunicações
• JBF.com
• Official JBL Store - Speakers, Headphones, and More!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>