EUKI 2AJ3G-R1 Video Doorbell Battery Powered User Guide

EUKI 2AJ3G-R1 Video Doorbell Battery Powered

Specifications:

• Product: Video Doorbell (Battery Powered)
• Features: Motion detection, two-way audio communication, video recording
• Power Source: Rechargeable battery
• Connectivity: Wi-Fi
• Additional Component: Wi-Fi Doorbell Chime with MicroSD card slot

Introducing the Video Doorbell
The video doorbell is designed to detect motion at your porch and allows you to answer the door from anywhere. It comes with mounting accessories and a USB charging cable for convenience.

Setting Up the Video Doorbell

1. Position the video doorbell at your porch using the mounting wedge and screw it in place.
2. Connect the USB charging cable to the doorbell for charging when needed.
3. Ensure the doorbell is securely attached using the detaching pin.

Introducing the Wi-Fi Doorbell Chime:
The Wi-Fi Doorbell Chime stores video clips using a MicroSD card and notifies you when someone rings the doorbell. It features indicator lights for status updates.

Video Doorbell (Battery Powered)

Quick Start Guide

What’s in the Box

Introduce the Video Doorbell

The video doorbell detects motion at your porch and allows you to answer the door anytime and anywhere.

Chime
Orange light is solid on| Doorbell is Charging
Off| Fully charged/ Sleep
Blue light is solid on| Booting/ Press Doorbell Button/ Alarm Detection

effect.
Power off the doorbell| Press and hold the Power Switch button until you hear Shutdown sound effect(About 10 seconds)
Add doorbell to Homebase| Quick-press the Power Switch button 3 times in 3 seconds, and quick-press the reset button on the chime 3 times in 3 seconds at the same time.

Introduce the Wi-Fi Doorbell Chime

The doorbell chime stores video clips with SD card, when someone rings the doorbell, people in the house will be notified.

voice prompt: “Reset success, device is restarting, please wait.”
Add doorbell to HomeBase| Quick-press the reset button 3 times in 3 seconds, and quick-press the Power Switch button on the chime 3 times in 3 seconds at the

same time.

Set up the Chime

Fix the power connector to Wi-Fi Doorbell Chime

• Step1.
  Place the power connector over Wi-Fi Doorbell Chime as indicated.

• Step2.
  Align the raised slots of the power connector with the notch on the base of the doorbell chime.

• Step3.
  Push hard in the direction as indicated to lock the power connector in place.

Note: Power plug may vary in different regions.

Set up the Doorbell on phone
Follow the steps below to get started with your new doorbell.

1. Step 1. Download the“SmartCam View”App
   Get the“SmartCam View”app from the APP Store or Google Play.Or download the APP by scanning below QR code.

2. Step 2. Login and add device

3.  Run the“SmartCam View”app, sign up for a SmartCam View Life account.

4. Login with your account ID, tap“+ Add Device”and scan the setup QR code on the Doorbell Chime.

5. Plug the chime into the power socket at your desired location. The LED indicator turns blinking red, when the doorbell chime is ready for setup.

6. Extend Wi-Fi Doorbell Chime’s antennas. we recommend that you place the antenna upward and try not to have anything blocking it, as this will provide better WiFi quality.

7. Follow the onscreen instructions to finish the initial setup.

Install the Doorbell

1. Step 1. Finding a Mounting Spot
   Take the video doorbell to your front door and check the live view on the App at the same time. Find a location where you can get the desired field of view.
   Consider the below factors:

2. Check if you can reuse the existing holes and anchors on the wall or door frame.

3. If you want to place the doorbell close to a side wall, make sure the wall doesn’t show up in the field of view. Otherwise IR light will be reflected and night vision will become blurry.

4. If you are drilling the mounting holes for the first time, the recommended mounting height is 55″ / 1.4 meters from the ground.

5. Use the 15° mounting wedge as a supplementary mounting bracket if you wish to see more on a specific side.
   

6. Step2.
   Find a suitable height to place the Screw Hole Positioning Card.

Step3. Determining the power option

Option 1 – Battery Powere

1. If you don’t have existing doorbell wiring at the front door, use the built-in battery. You are free to determine the doorbell position and the mounting is easy and quick.

2. If the doorbell battery is low, you need to charge it before installing it.

3. Mount the Bracket, Please NOTE That The Mounting Bracket has a positive indicator showing the installation direction pointing upward from the ground.

If you need to adjust the angle of the doorbell to see more on a specific side, you can use the 15° mounting wedge provided.

1. Place the Screw Hole Positioning Card
2. Drill and install anchors.( Anchors are not required if the wall is made of wood)
3. Mounting Bracket (If the installation surface is smooth and dust-free, you can use 3M tape along the edges behind the mounting bracket, eliminating the need to drill holes)
4. Screw the mounting bracket into position.
5. Install the 15° mounting wedge if you wish to see more on a specific side.

Align the slot of the doorbell with the bracket buckle, put it in, and press it down until it clicks into place.

Congratulations, you have completed the doorbell installation !

Option 2 – Doorbell Wire Powered

1. If you have existing and working doorbell wiring at the front door, the doorbell will be powered by the wires constantly. So you don’t need to detach and charge it after installation.

2. Ring the existing doorbell to check if it is working. If the doorbell doesn’t ring, your doorbell wires may be defective. Power the doorbell on its own battery or consult an electrician to fix the wires first.

3. Shut off the doorbell power supply. If you’re not sure, shut off the main power supply in your house. Turn the lights in your home on / off to make sure the electricity in your house is properly shut off.

4. Always be careful when handling electricity wiring. If you’re not comfortable to do it yourself, do consult a qualified electrician.

5. Find the doorbell chime in your house, then remove the cover and find the screw terminals with TRANS and FRONT markings. Use the provided Jumper for Existing Chime to connect the two terminals. This is to bypass the doorbell chime and will not affect the normal operation of the circuit.
   NOTE :

   • The video doorbell requires user to bypass the existing chime first to get sufficient power. Without this step, the video doorbell will still be able to power on but will operate unstably.

   • In most cases, the existing doorbell circuit looks like below chart. Find the existing doorbell chime in your house, remove the cover and take a photo of the wire connection in case you need to reconnect it.

   • Use the provided jumper to connect FRONT and TRANS terminals to bypass the chime on the circuit. Do not remove the original wire connecting to the chime. If your doorbell chime has different markings or you have multiple chimes, do consult a qualified electrician.

   • When the jumper is in place, the existing chime will not sound anymore.

   • Remove the existing doorbell button at the front door. Pull the two wires out carefully when removing the old doorbell. Straighten the wire ends if necessary.

   • Mount the Bracket, Please NOTE That The Mounting Bracket has a positive indicator showing the installation direction pointing upward from the ground.

   • If you need to adjust the angle of the doorbell to see more on a specific side, you can use the 15° mounting wedge provided.

   1. Place the Screw Hole Positioning Card
   2. Drill and install anchors.( Anchors are not required if the wall is made of wood)
   3. Mounting Bracket (If the installation surface is smooth and dust-free, you can use 3M tape along the edges behind the mounting bracket, eliminating the need to drill holes)
   4. Screw the mounting bracket into position
   5. Install the 15° mounting wedge if you wish to see more on a specific side.

6. Connect the wires to the two terminals at the back of the doorbell, then tighten the terminal screws. Wire can connect to any terminal as the electric current is alternating current.
   Note: To prevent short-circuit, make sure the wires are not touching each other after connecting them to the terminals. Use electrical wiring tape to secure the connection if the wall doesn’t have space for wire nuts.

7. Align the slot of the doorbell with the bracket buckle, put it in, and press it down until it clicks into place.

8. Switch the doorbell or master circuit breaker to ON.

Congratulations, you have completed the installation!

Detach the Doorbell

1. Use the doorbell detaching pin provided if you wish to detach the doorbell from the Mounting Bracket.
2. Press and hold the Release hole on the bottom of the doorbell and then lift its bottom to take it off.

Notification of Compliance

Compliance Statement
This device complies with Part 15C of FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. . This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving an tenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Compliance Statement

The transmitter/receiver exempt from licensing contained in this device complies with Innovation, Science and Economic Development Canada’s
(ISED) regulations applicable to license-exempt radio apparatus. Operation is subject to the following two conditions:

1. This device must not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

IC Radiation Exposure Statement:
This equipment complies with the radiation exposure limits set forth for uncontrolled environments in Canada. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Simplified EU Declaration of Conformity
SmartCam View declares that this device is in compliance with the essential requirements and other relevant provision of Directive EN300328,EN301489-1,EN31489-17,EN IEC 62311、EN IEC 62368.

Correct Disposal of This Product
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environment safe recycling.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>