MOTOEYE E6 HUD Helmet Smart HUD User Guide

MOTOEYE E6 HUD Helmet Smart HUD

Specifications:

• Model: E6/E6-SE M6/M6-SE
• Brand: Vidoar
• Website: www.vidoar.com
• Power Input: 5V
• Connection: Type-C
• Compatibility: iPhone and Android devices

Product Usage Instructions

Install HUD Host:

1. Remove the release paper from the base of the host.
2. Attach the base of the host behind the helmet and press it down firmly.
3. Adjust the camera’s perspective up and down as needed.
4. To remove the host, gently press the latch on the base and then remove the host.

Install Display Module:

1. Paste the back glue on side A or side B of the display module base.
2. Attach the base of the display module onto the helmet brim with the prism positioned directly forward and upward of the eye level.

Install Headset and TF Card:

1. Attach the headset to the reserved position inside the helmet.
2. Insert the earphone plug into the earphone jack.
3. Insert a TF card into the TF card house using a cross screwdriver and install the cover.

Install Remote Controller:

1. Rotate the controller counterclockwise to remove it from the base.
2. Install the controller base onto the bracket using a wrench and attach back glue to the arc position of the bracket.

Helmet Smart HUD
Quick Guide

This manual is applicable to the following models
E6/E6-SE
M6/M6-SE

Xi’an Vidoar Technologies Co., Ltd.
www.vidoar.com

Appearance Description

Packing List

Install HUD Host

1. Remove the release paper from the base of the host.
2. Stick the base of the host behind the helmet and press it down until it is firmly attached.
3. Adjust the camera’s perspective up and down.
4. To remove the host, gently press the latch on the base of the host, and then remove the host.

Install Display Module

1. Paste the back glue on side A or side B of the display module base.
2. Paste the base of the display module onto the brim of the helmet, so that the prism of the display module is in a position that is directly forward and upward of the human eye.
3. Insert the plug of the display module cable into the display jack of the HUD host.
4. Putting on the helmet and power on the HUD, fine tune the rotation shaft and sliding rail, so that you can see the image in the display module clearly.

Install Headset and TF Card

Install headset
Remove the release paper on the back of the headphones and microphone, stick it to the reserved position on the inside of the helmet, and insert the earphone plug into the earphone jack.

Storage cable
After installation, insert the exposed cables into the gap between the helmet and the internal sponge.

Install TF card
Use a cross screwdriver to open the TF card house, install the TF card, and then install the cover.

Install Remote Controller

1. Rotate the controller counterclockwise to remove it from the base.
2. Use a wrench to install the controller base onto the bracket and attach the back glue to the arc position of the bracket.
3. Remove the release paper from the bracket, paste the assembled bracket onto the handlebar, and press to ensure reliable installation.
4. If need to replace the battery,you can use a coin to open the battery cover and replace the battery.

functional Definition

Key

Indicate LED

Start Using

Power on/off：
Press and hold the power key for 2s to power on/off,After the HUD host is power on, short press the power key to standby/wake up the Display module.

note:
Please connect the display module plug to the host before power on,if an abnormality occurs, pressing and holding the power button for 10s can forcibly restart the device.

Charging：
Please use a 5V charger,when charging: the red charging indicator light remains on,when fully charged: the charging indicator light goes off,the charging time of the HUD is about 2.5 hours at a time.

Volume control：
Long press the up key to increase the volume,long press the down button to decrease the volume.

Download Mobile APP

When using it for the first time, you need to download the MOTOEYE app on your phone and connect to the HUD once. The HUD will Automatically complete language, time zone, time, and other settings.

Product software upgrades may result in operational differences.
For latest and detailed instructions of this product, please refer to the User Manual in MOTOEYE APP or scan the Online Manual QR code.

Bluetooth Connection

MOTOEYE APP connection:

1. Power on the HUD.
2. Download MOTOEYE mobile APP, register and log in.
3. Click on the “Device” on the APP homepage.
4. Search for the HUD host and click on the name to connect, the name  of HUD Bluetooth is :”device model” – “SN number”, such as M6-47C132C2.
5. After connected, the “Device” page will display the device information.

Bluetooth audio connection:
Android phone: Android mobile APP can establish bluetooth data and audio connection between HUD and phone simultaneously.
(Some models need to manually connect bluetooth audio in the system settings);

IPhone : The iOS APP can only establish a bluetooth data connection between HUD and the phone, and the audio connection needs to be manually connected in System Settings – Bluetooth Connection.

Networks Connection

WiFi connection:

1. After establishing the bluetooth connection, click the “WiFi” button.
2. Select the WiFi you wanted and enter the password to connect.

Share mobile network through bluetooth:

1. Before sharing the mobile network through bluetooth, the following settings need to be made on the phone:
   IPhone: Turn on the ‘Personal Hotspot’ switch.
   Android phone: Turn on the “Bluetooth shared network” switch.

2. In the settings menu of the HUD host, enter the “Bluetooth network” page and click “Connect”.

3. If turn on the “Auto Connect” switch on the “Bluetooth network” page,the HUD will automatically connect to the network after connected to the phone’s bluetooth audio.

Using The Remote Controller

After the HUD is turned on, press any key on the remote controller and wait for a few seconds. The controller can resume connection to the HUD. After the HUD shuts down, the remote controller will automatically enter low-power sleep mode.

If you need to pair the Bluetooth remote controller again, you can proceed as follows:

1. Press and hold the camera button and return button of the controller simultaneously for more than 3 seconds. At this time, the red and blue lights on the remote control flash alternately.
2. After establishing a Bluetooth connection between the phone and the HUD host, click the controller button on the APP homepage or “Device Connection” page.
3. Click on “Search bluetooth Controller”.
4. Select the bluetooth controller to connect to.

Warranty Policy

During the normal use of this product, if there are quality issues that are not caused by human factors, the product can enjoy the following services after being tested and confirmed by our company:

1. If there is a product quality issue within 7 days from the day after receiving it, users can enjoy free return or exchange services.
2. If there is a product quality issue within 15 days from the day after receiving it, users can enjoy free replacement or repair services.
3. If there are product quality issues within one year from the day after receiving it, users can enjoy free repair services.

If one of the following conditions is met, it is not covered by the warranty.

1. Damage caused by force majeure factors, such as earthquakes, fires, floods, typhoons, etc.
2. Damage caused by improper use, maintenance, or storage.
3. Damage caused by failure to use, maintain, and adjust according to the requirements of the user manual.
4. Damage caused by unauthorized personnel disassembling, repairing, or modifying without authorization from our company.
5. The warranty period has expired.
6. Situations not covered by warranty as stipulated by laws and regulations.

Warranty Card

Products

| Model|
---|---|---
SN number|
Purchasing date|

User

| Name|
Phone number|

Address

|

Distributor

| Name|
Telehpone|

Address

|

FCC Warnning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuan t to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterferenc e to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:

• Reorient or reloca te the receiving antenna.
• Increase the separation between the equi pment and receiver.
• Connect the equipment into an outlet on a circuit different f rom that to which the receiver is c onnected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference r eceived, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.

Frequently Asked Questions (FAQ):

How do I power on off the HUD?

To power on off the HUD, long press the power key for 2 seconds. The status LED will indicate when it is powered on or off.

How do I adjust volume or start voice control?

Use the up down keys to increase/decrease volume, and long press the OK key to start voice control.

How do I switch between different modes?

Use the left right keys to navigate between different modes such as rearview mirror, intercom, and PTT Push-to-Talk.

References

• vidoar.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>