adeo S36-326 Ceiling Fan with LED Light Installation Guide

June 1, 2024
adeo

adeo Logo INSTALLATION GUIDE

Ceiling Fan with LED Light

WELCOME

Thank you for choosing our Ceiling Fan with LED Light.
n this manual you will find the instructions, warnings and recommendations necessary to enjoy our product safely and satisfactorily. Before connecting your appliance, take time to carefully read the safety precautions.

PARTS

Carefully open the packaging. Remove the tems from their Styrofoam inserts. Remove the motor housing and place t somewhere safe (in the Styrofoam) to avoid damaging the finish. Check the parts inventory to make sure that all parts have been included.

adeo S36 326 Ceiling Fan with LED Light  - Part

INSTALLATION PREPARATION

To prevent personal injury and damage, ensure that the blades are at least 2.3m from the floor and also leave a 76cm space from any wall or object that may obstruct.
Be sure the outlet box is securely attached to the installation surface and can fully support the weight of the fan.

PREPARING THE FAN SITE

Down-rod Installation
This fan can be mounted with a down-rod onto either a normal or vaulted ceiling. The hanging ength can be extended by a longer down-rod. For installation, we’ll require these tools: a screw­ driver, a flat-head screwdriver, an adjustable pliers or wrench, a stepladder, wire cutters, and rated electrical tape.
Standard Mounting Style

Standard Mounting hangers from the ceiling using a down-rod.

Angled Mounting Style

Angled Mounting recommended for a vaulted or angled ceiling.

INSTALLING THE HANGER BRACKET

adeo S36 326 Ceiling Fan with LED Light  - Standard 2

Drill an 08mm hole into the concrete ceiling and insert the bolt. Align the bracket with the hole, then tighten using a nut.

ASSEMBLING AND HANGING THE FAN

Replacing the downrod
If you wish to extend the height of your fan, you must remove the hanging ball from the provided 6 inch down-rod. Then use the extended down-rod (included). If you wish to use the 6 inch down­ rod, please proceed using the instructions below:

  1. To remove the hanging ball, loosen the screw found on the hanging ball and remove both the pin and clip. Lower the hanging ball and remove the pin. Slide the hanging ball off the original down-rod, and slide it down onto the onger down-rod (the top of the down-rod can be identi­ fied by finding the screw hole; use this hole when fitting the screw).
  2. Insert the pin into the top of the extended down-rod, then raise the hanging ball. Make sure that the pin aligns with the slots found within the hanging ball, then securely tighten the screw.
    Note: To prepare for threading the electrical wires through the down-rod, wrap a small piece of electrical tape around the ends of electrical wires. This will keep the wires together when threading them through the down-rod.

Connecting the downrod post to the engine

  1. Loosen yoke set screws and nut at top of motor housing. Remove pin and clip from downrod (if you have not already done so). Slide downrod through canopy.
  2. Tread electrical wires through down rod and pull extra wire slack from the upper end of the down rod.
  3. Place downrod into the motor housing yoke and ew-insert pin and clip that were previously removed. Tighten yoke set screws and nut securely. Lower canopy to motor housing.

adeo S36 326 Ceiling Fan with LED Light  - Engine

REMOTE CONTROL RECEIVER CONNECTION

adeo S36 326 Ceiling Fan with LED Light  - Remote

RECEIVER PLACE

CANOPY ASSEMBLY

Raise the canopy onto the hanging bracket, then align the loosened screws on the hanging bracket with the holes n canopy. Twist the canopy to lock it. Re- insert and tighten the screws using a screwdriver.
With the hanging bracket secured to the outlet box, you are now ready to hang your fan. Take the fan firmly with two hands. Slide the down-rod through the opening in the hanging bracket and et hanging the ball rest on the hanging bracket. Turn the hanging ball slot until t lines up with the hanging bracket tab.
Note: Seek the help of another person to hold the stepladder n place and to lift the fan up to you once you are up on the ladder.

adeo S36 326 Ceiling Fan with LED Light  - Place 1

BLADE ASSEMBLY
The washers for the blade screws can be set onto the screws before the blades are locked to the fan.
Align the blade holes with the motor screw holes. Securely tighten all the screws once all of the blades are attached. Before permanently tightening the screws, repeat with each remaining blade arm.

adeo S36 326 Ceiling Fan with LED Light  - Place 2

LED PAN ASSEMBLY
Unscrew the set screw. Attach the LED pan to the bottom of the fan by inserting the other two set screw into the corresponding slots. Rotate the unit, then secure the previous set screw by aligning to with the screw hole and the hole at the bottom of the fan. Finally, tighten the last two set screws to secure LED pan.
Note: While installing or removing the LED pan, please keep the insulation pads intact. Over-tightening the set screws or will damage the insulation pads.

adeo S36 326 Ceiling Fan with LED Light  - Place 3

A. Lamp panel
B. Lamp panel screw

LED LIGHT SOURCE ASSEMBLY
Place the cover and the LED Light source.

adeo S36 326 Ceiling Fan with LED Light  - Cover

LAMP SHADE ASSEMBLY
Return the cover and the amp shade back to the LED pan, then secure them with decorative clips and bolts.

adeo S36 326 Ceiling Fan with LED Light  - Cover 1

CAUTIONS AND WARNINGS

Carefully read this entire manual before proceeding to nstall. Store these instructions for possi­ble future use.
» Use only original replacement parts.
» To reduce the risk of personal injury, attach the fan directly to the support structure of the building according to these instructions and use only the supplied hardware.
» To avoid possible electrical shocks, before installing your fan, please disconnect the power by turning off the circuit breakers within the outlet box and any associated wall switches within the ocation. If you cannot ock the circuit breakers into the off position, securely fasten a prominent warning device, such as a tag, to the service panel.
» All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. if you are unfamiliar with electrical wiring, use a qualified electrician.
» To reduce the risk of personal injury, do not bend the blade attachment system when installing, balancing or cleaning the fan. Never insert foreign objects between rotating fan blades.
» To reduce the risk of fire, electrical shock or motor damage, do not use a solid-state speed control with this fan. Use only original speed controls.
Note: The important safety precautions and instructions contained in this manual cannot cover all possible conditions and situations that may occur. It must be understood that com­ mon sense and caution are necessary factors when installing and operating this fan.
In compliance with Directives: 2002/95CE, 2002/96/CE and 2003/108/CE on the restriction of the use of dangerous substances in electric and electronic equipment as well as their waste disposal. The symbol with the crossed dustbin shown on the package indicates that the product at the end of ts service life shall be collected as separate waste. Therefore, any products that have reached the end of their useful life must be given to waste disposal centres specializing n separate collection of waste electrical and electronic equipment, or given back to the retailer at the time of purchasing new similar equipment, on a one for one basis. – The adequate separate collection for the subsequent start-up of the equipment sent to be recycled, treated and disposed of in an environmentally compatible way contributes to preventing possible negative effects on the environment and health and optimises the recycling and reuse of components making up the apparatus. Abusive disposal of the product by the user involves application of the administrative sanctions according to the laws.

CHARACTERISTICS

FAN POWER 40W
LIGHT POWER 15W
VOLTAGE 220V AC DC Motor
RECOMMENDED INSTALLATION <10m 2
FAN DIAMETER 91cm/36″
HEIGHT FROM CEILING 39cm
ON/OFF FUNCTION Remote control
BLADE MATERIAL PLASTIC
N° OF SPEEDS 6 RPM: 200/180/160/140/120/100
N° OF BLADES 3
WINTER/SUMMER FUNCTION Yes
TIMER 1 /2/ 4/8 hours
WEIGHT 5,5kg

Tech is life
Prismica S.L. · 898845944
Cl Llevant, 2 · 46715 Valencia SPAIN

Documents / Resources

| adeo S36-326 Ceiling Fan with LED Light [pdf] Installation Guide
12175, S36-326, S36-326 Ceiling Fan with LED Light, Ceiling Fan with LED Light, Fan with LED Light, LED Light, Light
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals