adeo S1M-ZP7-115-5 Angle Grinder Instruction Manual

adeo S1M-ZP7-115-5 Angle Grinder

Product Information

Product Usage Instructions

General Safety Instructions:

• Read the installation, user, and maintenance instructions carefully.
• Ensure complete satisfaction with the product.
• If assistance is needed, contact the retailer.

Specific Safety Rules:

• Avoid working in disorderly or dark areas as they can lead to accidents.
• Do not place your finger on the switch or connect tools with the switch in the ON position.
• Be cautious of unexpected actions.
• Novice users should be careful while operating the tool.
• Avoid holding the tool in an unstable manner.
• Beware of tool rebound on your hand.

Tool Specifications:

Assembly and Usage Instructions

1. Refer to the provided drawings for an overview of the tool.
2. Ensure the correct protective cover is used based on cutting or grinding requirements.
3. Make sure the protective cover is properly installed.
4. Follow the instructions provided by the manufacturer.
5. Properly lubricate and store the tool after use.

Troubleshooting:

• If the machine does not start, check the power cord connection and replace it if necessary.
• If the motor overheats, check the grinding disc and adjust the feed rate accordingly.
• If the machine vibrates or trembles, replace the wheel if it is not round and ensure proper tightening of components.

Environmental Protection:
Follow local regulations for the disposal of the product.

Warranty:
The product is covered by a warranty. Refer to the warranty terms and conditions for more information.

Thank you for purchasing this product. We recommend that you read the installation, user and maintenance instructions carefully. We have designed this product to ensure your complete satisfaction. If you require  assistance, the team at your retailer is on hand to help you.

WARNING SYMBOLS

• To reduce the risk of injury, user must read instructional.
• In accordance with essential applicable safety standards of European directives.
• Class II machine – Double insulation – You don’t need any earthed plug.
• Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual.
• Indicates electrical shock hazard.
• Faulty and/or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations.
• Immediately unplug the plug from the mains electricity in the case that the cord gets damaged and during main-tenance.
• Wear eye protection
• Wear dust mask
• Caution! Wear gloves protection
• Wear safety shoes
• Wear ear protection
• Sign of product circulation in the market of the Customs Union member states.
• Conformity marking that product comply with applicable Ukraine technical regulations.

GENERAL SAFETY INSTRUCTIONS

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains- operated (corded) power tool or battery-operated (cordless) power tool.

Work area safety

• Keep work area clean and well lit. Cluttered and dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodifies plugs and matching outlests will reduce risk of electric shock.
• Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling or un-plugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
• When operating a power tool outdoors, use an extension cord suit-able for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

• Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce person-al injuries.

• Prevent unintentional starting. Ensure the switch is in the off-posi-tion before connecting to power source and/or battery pack,
  picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites acci-dents.

• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

• If devices are provided for the connection of dust extraction and col-lection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

Power tool use and care

• Do not force the power tool. Use the correct power tool for your ap-plication. The correct power tool will do the job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures re-duce the risk of starting the power tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
• Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired be-fore use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

Service

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Safety Warnings Common for Grinding Operations:

• This power tool is intended to function as a grinder .
  Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed be- low may result in electric shock, fire and/or serious injury.

• Operations such as sanding, wire brushing, polishing are or cut-off not recommended to be performed with this power tool. Operations for which the power tool was not designed may create a hazard and
  cause personal injury.

• Do not use accessories which are not specifically designed and recommended by the tool manufacturer. Just because the accessory can be attached to your power tool, it does not assure safe operation.

• The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart.

• The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or controlled.

• Threaded mounting of accessories must match the grinder spindle thread. For accessories mounted by flanges, the arbour hole of the accessory must fit the locating diameter of the flange. Accessories that do not match the mounting hardware of the power tool will run out of
  balance, vibrate excessively and may cause loss of control.

• Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear, wire brush for loose or cracked wires. If power tool or accessory is dropped, inspect for damage or install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time.

• Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and workshop apron capable of stop-ping small abrasive or workpiece fragments. The eye protection must be capable of stopping flying debris generated by various operations. the dust mask or respirator must be capable of filtrating particles generated by your operation. Prolonged exposure to high intensity noise may cause hearing loss.

• Keep bystanders a safe distance away from work area. Anyone entering the work area must wear personal protective equipment. Fragments of workpiece or of a broken accessory may fly away and cause in-
  jury beyond immediate area of operation.

•  Hold power tool by insulated gripping surfaces only, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator
  an electric shock.

• Position the cord clear of the spinning accessory. If you lose control, the cord may be cut or snagged and your hand or arm may be pulled into
  the spinning accessory.

• Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control.

• Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body.

• Regularly clean the power tool’s air vents. The motor’s fan will draw the dust inside the housing and excessive accumulation of powdered
  metal may cause electrical hazards.

• Do not operate the power tool near flammable materials. Sparks could ignite these materials.

• Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock.

Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory’s rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the wheel that is entering into the pinch point can dig into the surface of the material causing the wheel to climb out or kick out. The wheel may either jump toward or away from the operator, depending on direction of the wheel’s movement at the point of pinching. Abrasive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below.

• Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces. Always use auxiliary handle, if provided, for maximum control over kickback or torque reaction during start-up. The operator can control torque reactions or kickback forces, if proper precautions are taken.

• Never place your hand near the rotating accessory. Accessory may kickback over your hand.

• Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in direction opposite to the wheel’s movement at the point of snagging.

• Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the accessory. Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control
  or kickback.

• Do not attach a saw chain woodcarving blade or toothed saw blade. Such blades create frequent kickback and loss of control.

Safety Warnings Specific for Grinding and cutting-off Operations:

• Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe.

• The grinding surface of centre depressed wheels must be mounted below the plane of the guard lip. An improperly mounted wheel that projects through the plane of the guard lip cannot be adequately protected.

• The guard must be securely attached to the power tool and positioned for maximum safety, so the least amount of wheel is exposed towards the operator. The guard helps to protect operator from bro-ken wheel fragments and accidental contact with wheel and sparks that
  could ignite clothing.

• Wheels must be used only for recommended applications. For example: do not grind with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter.

• Always use undamaged wheel flanges that are of correct size and shape for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges.

• Do not use worn down wheels from larger power tools. Wheel intend-ed for larger power tool is not suitable for the higher speed of a smaller
  tool and may burst.

Additional safety instructions for wire brushing operations
NOTE If wire brushing operation is not recommended by the manufacturer, this section may be omitted.

Safety Warnings Specific for Wire Brushing Operations:

• Be aware that wire bristles are thrown by the brush even during ordinary operation. Do not overstress the wires by applying excessive load to the brush. The wire bristles can easily penetrate light clothing and/or skin.
• If the use of a guard is recommended for wire brushing, do not allow any interference of the wire wheel or brush with the guard. Wire wheel or brush may expand in diameter due to work load and centrifugal forces.

SPECIFIC SAFETY RULES

• Check that speed marked on the wheel is equal to or greater than the rated speed of the grinder;
• Ensure that the wheel dimensions are compatible with the grinder;
• Abrasive wheels shall be stored and handled with care in accordance with manufacturer’s instructions;
• Inspect the grinding wheel before use, do not use chipped, cracked or other-wise defective products;
• Ensure that mounted wheels and points are fitted in accordance with the manufacturer’s instructions;
• Ensure that blotters are used when they are provided with the bonded abrasive product and when they are required;
• Ensure that the abrasive product is correctly mounted and tightened before use and run the tool at no-load for 30 s in a safe position, stop immediately if there is considerable vibration or if other defects are detected. If this condition occurs, check the machine to determine the cause;
• Do not use separate reducing bushings or adapters to adapt large hole abrasive wheels;
• For tools intended to be fitted with threaded hole wheel, ensure that the thread in the wheel is long enough to accept the spindle length;
• Check that the work piece is properly supported;
• Ensure that sparks resulting from use do not create a hazard e.g. do not hit persons, or ignite flammable substances;
• Ensure that ventilation openings are kept clear when working in dusty conditions. If it should become necessary to clear dust, first disconnect the tool from the mains supply (use non metallic objects) and avoid damaging internal parts;
• Always use eye and ear protection. Other personal protective equipment such as dust mask, gloves, helmet and apron should be worn;
• The wheel continues to rotate after the tool is switched off.
• Never use the tool without the guard in place, the wheel guard must be fitted on the tool so that the closed side of the guard always points toward the operator.

INTENDED USE

• WARNING! Always wear protective goggles.

Thank you for purchasing this product. Please read through these operating instructions and keep them for future reference. This angle grinder is intended for grinding or cutting metal without the use of water. After unwrapping the packaging, make sure that the product is complete with its accessories (if any). If the product is damaged or has any defect, please do not use it and bring it back to your dealer. If you give this tool to other people, please give him also this instruction manual. Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes. For safety reasons, children and young people under the age of 16, as well as people not familiar with these operating instructions, may not use this product. Persons with reduced physical or mental abilities may use the product only if they are supervised or instructed by a responsible person. Observe the specifications of the tool or accessory manufacturer! Protect the discs from grease or impact!
Never use parting grinder discs for roughing work! Do not apply pressure to the side of parting grinder discs.
The workpiece must lay flat and be secured against slipping, e.g. using clamps. Large workpieces must be sufficiently supported.
If accessories with threaded inserts are used, the end of the spindle may not touch the base of the hole on the sanding tool. Make sure that the thread in the accessory is long enough to accommodate the full length of the spindle. The thread in the accessory must match the thread on the spindle.
When working in dusty conditions, ensure that ventilation openings are not blocked. If it becomes necessary to remove dust, first up plug and avoid damaging internal components.
Damaged, eccentric or vibrating tools must not be used.
Avoid damage to gas or water pipes, electrical cables and load-bearing walls(static).
Remove the power plug from the socket before making any adjustments, changing tools, maintaining or cleaning.
In order to avoid a hazard, before set switched ON, make sure the grinder discs is not touch workpieces.
A damaged or cracked additional handle must be replaced. Never operate the machine with a defective side handle.
A damaged or cracked safety guard must be replaced. Never operate a machine with a defective safety guard.
Secure small workpieces. For example, clamp in a vice.
DO NOT use grinding wheels other than center depressed wheels and flap discs. DO NOT use under wet conditions or in the presence of flammable liquids or gases.

ENVIRONMENTAL PROTECTION

CAUTION! This product has been marked with a symbol relating to removing electric and electronic waste. This means that this product shall not be discarded with household waste but that it shall be returned to a collection system which conforms to the European WEEE Directive. Contact your local authorities or stocks for advice on recycling. It will then be recycled or dismantled in order to reduce the impact on the environment. Electric and electronic equipment can be hazardous for the environment and for human health since they contain hazardous substances.

TOOL SPECIFICATIONS

TECHNICAL CHARACTERISTICS|
Rated voltage| 220-240V~
Rated frequency| 50 Hz
Rated input power| 500 W
Rated speed Max.| 12000 /min
Disc diameter| 115 mm
Disc thickness| 6mm for grinding disc
Weight| 1.72 kg
Spindle thread| M14
LpA (Sound pressure level)| LpA : 90.7 dB(A)
KpA: 3.0 dB(A)
LwA (Sound power level)| LwA : 101.7 dB(A) KwA: 3.0 dB(A)
Vibration level| 6.5 m/s2 K=1.5 m/s2
Protection class| II
Degree of protection| IPX0
Main size| 31.5×13.8×10.4 cm

The declared vibration total value has been measured in accordance with a standard test method and may be used for comparing one tool with another; The declared vibration total value may also be used in a preliminary assessment of exposure.

• Warning: the vibration emission during actual use of the power tool can differ from the declared total value depending on the ways in which the tool is used.
• Warning: avoid vibration risk Suggestions:
  • wear glove during operation;
  • limit operating time and shorten trigger time.

OPERATION / ASSEMBLY / DRAWINGS

Overview

1. Paddle
2. Side handle
3. Protective cover (grinding115mm)
4. Guard locking lever
5. Gear box
6. Lock button
7. Spanner
8. External flange with thread
9. Internal flange
10. Safety interlock

Mounting the Auxiliary Handle
The side handle can be fitted to the left, right of the unit. Select the position which gives the most comfortable and safe use.

CAUTION:
Always be sure that the side grip is installed securely before operation. During operation, keep one hand on the rear handle and the other on the side handle. Installing or moving protective cover

WARNING: Ensure the angle grinder is switch off and unplugged from the mains.
Depending on whether your operation is cutting or grinding, select the correct protective cover. Failure to use the right cover for operation could result in inju-ry. When using a grinding or cutting-off wheel, the protective guard must be fit-ted on the tool so that the closed side of the cover always points toward the op-erator.

Mounting and removing the Guard
Mounting
Place the angle grinder on a ¦at and steady surface, spindle up.
Align the lug with the slot in the bracket.
Press the guard down and turn it in the direction of the arrow until it is in the working position providing maximum protection to the user.
Insert the bolt to the holes on the bracket, Screw the nut on the thread of the bolt.
Use a 4mm hex wrench (not supply) to tighten the bolt and nut.
Do not operate the grinder with a losse guard.

Removing
Follow the procedure above in reverse orders.
Use a 4mm hex wrench (not supply) to loosen the nut, turn counterclockwise to 2 salient points, align and remove the guard. Please note that there are limited points on the screw to ensure that the nut cannot be unscrewed when it is un-screwed to a certain position.

Please use grinding protective cover for grinding operation.

Grinding and Surface Processing
In order to grind surface, you should use a coarse abrasive disk with a sunken centre.
You can use the abrasive disks with diameter of 125mm. The maximum thick-ness of disks is 6mm.

Mounting the Wheels /Disks
Place the back flange A over the spindle making sure that it fits tight.
Place the grinding or cutting disc B on the top of the back flange, ensuring the bore fits into the step of the flange.
Mount the concave recess side of the external flange C over the spindle.
Press the spindle lock button to lock the spindle firmly, then tighten the external flange with the spanner in clockwise direction.
Allow the angle grinder to run in idle at least 1 minute with the grinding or cut-ting disc correctly assembled, a vibration disc should be immediately replaced.

OPERATING INSTRUCTIONS / DRAWINGS

Switch ON/OFF
Switch on: Push the safety interlock forwards meanwhile clenching the paddle to turn on the machine. Then keep hold it in position for continuous operation. Switch off: Loosen the paddle and turn off the machine, go loosen the safety interlock to lock witch at OFF position.
WARNING: Do not cover exhaust vents when the tool is in use. This may cause damage to the motor and reduce the efficiency of the tool.

Abrasive operation
When equipped with abrasive wheel and guard, for the best work results hold the grinder at 15~20° to the work piece.

Overload
The motor of your right angle grinding machine may be damaged when over- loaded. This results from excessive working pressure over a prolonged peri-od. Therefore you should not try to accelerate your working speed by increasing pressure on your machine. The abrasive disks work more efficiently if only slight pressure is exerted on the grinding machine, thus avoiding a drop in the grinding speed.

MAINTENANCE / CLEANING /LUBRICATION / STORAGE

Maintenance
Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance.
If the replacement of the supply cord is necessary, this has to be done by the manufacturer or his agent in order to avoid a safety hazard.

Cleaning
The tool and its air vents have to be kept clean. Regularly clean the tool’s air vents or whenever the vents start to become obstructed.
Avoid using solvents when cleaning plastic parts. Most plastic parts are susceptible to damage from various types of commercial solvents and may be dam-aged by their use. Use clean clothes to remove dirt, carbon dust, etc.

Lubrication
All the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions, therefore no further lubrication if required.

Storage
Store the angle grinder in a dry place. Regularly inspect the disks / wheels, ensure that the disks / wheels is free of cracks and surface defects. Replace the disks / wheels when it has wore out.
Take care not to expose this tool to the rain.

CHECK THE DELIVERY PARTS

Carefully remove the tool from its packaging and check if the following parts are complete:

• 1 x Angle grinder
• 1 x Side handle
• 1 x 115mm grinding protective cover
• 1 x spanner
• 1 x External flange (assembled on the machine)
• 1 x Internal flange (assembled on the machine)

TRACEABILITY NUMBER / SERIAL NUMBER

The Traceability Number/Serial Number will be showed in the label.

TROUBLESHOOTING

1. Power cord not plugged in.
2. Power cord is damaged.
3. Circuit breaker is tripped.
4. Switch is locked at “OFF” conditions.

|

1. Plug in cord.
2. Replaced at authorized service center.
3. Reset circuit breaker.
4. Restart the tool.

Motor does not reach full.|

1. Voltage from power source.
2. Circuit is overloaded.
3. Motor burned out.

|

1. Request a voltage check.
2. Test on a different circuit or without anything else on circuit.
3. Have tool serviced and request a voltage check.

Motor stalls, blows fuses, or trips circuit breakers.|

1. Switch is defective.
2. Carbon brush is wornout.
3. Voltage from source is low.
4. Fuses or circuit breakers are wrong size or defective.

|

1. Replaced at authorized service center.
2. Replace at authorized service center.
3. Request a voltage check.
4. Replace with a correct circuit breaker or fuses.

Motor overheats.|

1. Motor is overloaded.
2. Grinding disc is being fed into work too fast.
3. Air vents become obstructed.

|

1. Request a voltage check.
2. Feed grinding into work slower.
3. Clean air vents.

Machine| Disc is out-of-round.| Replace wheel.
vibrates| Disc is chipped.| Replace wheel.
or shakes.|

1. Disc is loose.
2.  Machine is not secure.

| Set flange nut correct and tighten it.
| Work surface is uneven.| Check machine and all hardware.
| | Feed grinding into work
| | slowly.

GUARANTEE

This products are designed based on the most rigorous quality standards for products intended for the general public.
The Angle Grinder (Model n° S1M-ZP7-115-5) is covered with a warranty of 1 years. starting from the date of purchase. This warranty covers all manufactur-ing or material defects.
In the event of a breakdown, please refer first to the troubleshooting page (problems and solutions)in the brochure; if the problem persists, please check with the nearest store.
You store shall spare no effort in resolving the issue.
Repairs and change of parts do not extend the duration of the initial warranty. Breakdowns resulting from normal wear and tear or from improper use of the product are not covered by the warranty. This includes, among others, the switches, the safety circuit breaker and the motors, in case of wear.
Please note that there are specific warranty terms for certain countries.
In case of doubt, please check with your point of sale.
For claims relating to the the warranty to be taken into account, the following is required:

• Providing proof of purchase
• That no repairs and/or change of parts have been performed by a third party. . That the issue is not a matter of normal wear and tear.
• That required maintenance and repair works have been performed correctly. . That no deterioration has taken place as a result of incorrect setting of the carburetor.
• That there has been no forcing, improper handling, unauthorized use, or accidents.
• That no deterioration has taken place due to overheating, resulting from clogging of the ventilator block.
• That no work has been done on the product by an unskilled person, and no incorrect repairs have been attempted.
• That the tool/battery/charger have never been disassembled or opened.
• That the tool/battery/charger have never been in a wet environment (dew, rain, submerged in water…)
• That no incorrect parts have been used, whereas they prove to be the cause of deterioration.
• That the tool has not been used improperly (overloading the tool, or use of non-approved accessories).
• That no damage has resulted from external causes, or foreign bodies such as sand or stones.
• That no damage has resulted from non-compliance with safety recommendations and use instructions.
  The product must be used under normal usage circumstances, and for non- professional purposes.
  Therefore, excluded from this warranty are products used by landscaping companies, local authorities, as well as companies offering paid rentals or free loaning of equipment.

Parts

Assembly

USE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>