TOA IP-A1PC580R Ceiling Mount Speaker Instruction Manual

TOA IP-A1PC580R Ceiling Mount Speaker

Product Specifications:

• Model: IP-A1PC580R (Ceiling Mount Speaker) / IP-A1PC580S (Square Speaker)
• Equipped with built-in power amplifier and sound source memory
• Connectivity: Can be connected to and used over a local network
• Internal sound source broadcasting mode
• VMS broadcasting mode and SIP broadcasting mode
• Multicast broadcasting mode: Allows up to 20 multicast ports to be set up

Product Usage Instructions

Installation:
Follow the dimensional drawings provided in the manual to properly install the speaker in your desired location.

Connectivity:
Connect the speaker to a local network using the appropriate cables and ensure proper network settings are configured.

Broadcasting Modes:

• Internal Sound Source Broadcasting Mode: Use control input or Remote API to broadcast up to 20 internal sound source files.
• VMS Broadcasting Mode and SIP Broadcasting Mode: Enable audio broadcast from VMS software or SIP broadcasts from voice communication devices.
• Multicast Broadcasting Mode: Set up multicast ports for audio stream paging groups.

Frequently Asked Questions (FAQ):

• Q: Can I modify the speaker?
  A: Any modifications not approved by TOA Corporation may void the warranty and FCC authorization to operate the equipment.

• Q: What should I do if the Line/Mic input signal indicator lights up in red?
  A: Adjust the Line/Mic input volume control to decrease the volume level until the indicator no longer lights up in red.

INSTRUCTION MANUAL
IP CEILING MOUNT SPEAKER IP SQUARE SPEAKER
IP-A1PC580R IP-A1PC580S

• Thank you for purchasing TOA’s IP Speaker.
• Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.

SAFETY PRECAUTIONS

• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe operation.
• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or cautions regarding safety.
• After reading, keep this manual handy for future reference.

WARNING Indicates a potentially hazardous situation which, if mishandled, could result in death or serious personal injury.
CAUTION Indicates a potentially hazardous situation which, if mishandled, could result in moderate or minor personal injury, and/or property damage.

WARNING

• When Installing the Speaker
  • Do not expose the speaker to rain or an environment where it may be splashed by water or other liquids, as doing so may result in fire or electric shock.
  • Install the speaker only in a location that can structurally support the weight of the speaker and the mounting bracket. Doing otherwise may result in the speaker falling down and causing personal injury and/or property damage.
  • Since the speaker is designed for indoor use, do not install it outdoors. The speaker is to be connected only to PoE networks without routing to the outside plant. If installed outdoors, the aging of parts causes the speaker to fall off, resulting in personal injury. Also, when it gets wet with rain, there is a danger of electric shock.
  • Do not mount the speaker in locations exposed to constant vibration. The mounting bracket can be damaged by excessive vibration, potentially causing the speaker to fall, which could result in personal injury.
• When the Speaker is in Use
  • Should the following irregularity be found during use, immediately cut off the power supply from a PoE switching hub and contact your nearest TOA dealer. Make no further attempt to operate the speaker in this condition as this may cause fire or electric shock.
  • If you detect smoke or a strange smell coming from the unit
  • If water or any metallic object gets into the speaker
  • If the speaker falls, or the speaker case breaks
  • If the LAN cable is damaged (exposure of the core, disconnection, etc.)
  • If the speaker suddenly stops producing sound
• To prevent a fire or electric shock, never open nor remove the speaker case as there are high voltage components inside the speaker. Refer all servicing to qualified service personnel.
• To prevent the electromagnetic wave from badly influencing medical equipment, make sure to switch off the speaker’s power when placing it in close proximity to the medical equipment.

CAUTION

• When Installing the Speaker
  • Attach the safety wire to the speaker. If not attached, the speaker could fall off, resulting in personal injury.
  • Avoid installing the speaker in humid or dusty locations, in locations exposed to the direct sunlight, near the heaters, or in locations generating sooty smoke or steam as doing otherwise may result in fire or electric shock.
  • Avoid touching the speaker’s sharp metal edge to prevent injury.
• When the Speaker is in Use
  • Do not operate the speaker for an extended period of time with the sound distorting. Doing so may cause the speaker to heat, resulting in a fire.
  • Have the speaker checked periodically by the shop from where it was purchased. Failure to do so may result in corrosion or damage to the speaker or its mounting bracket that could cause the unit to fall, possibly causing personal injury.

This equipment is not suitable for use in locations where children may be present.

FCC REQUIREMENTS

Note

• This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
• Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Modifications
Any modifications made to this device that are not approved by TOA Corporation may void the authority granted to the user by the FCC to operate this equipment.

DECLARATION

• Any modification to the unit, unless expressly approved by TOA Electronics, Inc., could void your authority to operate the equipment.
• DECLARATION OF CONFORMITY
  • TOA Electronics, Inc.
  • 1 Harmon Plaza, Suite 700 Secaucus, New Jersey 07094, USA TEL 650-452-1200
  • declares under its sole responsibility that the products
• IP CEILING MOUNT SPEAKER IP-A1PC580R IP SQUARE SPEAKER IP-A1PC580S comply with Part 15 of FCC Rules.
• Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The IP-A1PC580R and IP-A1PC580S IP speakers are capable of delivering extremely high volume sound output. Therefore, close proximity to the speaker over time could present the danger of hearing impairment. Be sure to follow the instructions below when conducting performance tests:

• Turn down the sound volume before adjusting the volume.
• Do not position one’s ear close to the speaker.
• Point the speaker in a direction where no people are present.
• Avoid listening to high-volume output for prolonged periods of time.

SUMMARY AND FEATURES

• The IP-A1PC580R/A1PC580S IP speakers are equipped with a built-in power amplifier and sound source memory.
• It can be connected to and used over a local network.
  • Power is supplied by way of PoE switching hubs.
  • The IP speakers are compatible with the following broadcasting modes:

Internal sound source broadcasting mode| Enables broadcast of up to 20 internal sound source files by means of control input or Remote API (HTTP).
---|---
VMS broadcasting mode| Enables backchannel audio broadcast from the VMS (Video management system) software using the common protocol for IP cameras.
SIP broadcasting mode| Enables SIP broadcasts from any voice communications device that utilizes the SIP protocol, such as SIP or IP telephone (IP- PBX) systems.
Multicast broadcasting mode| Allows up to 20 multicast ports to be set up, for 20 multicast audio stream paging groups.

• Orders of priority can be set among the various broadcasting modes, meaning higher priority broadcasts can interrupt and override lower priority broadcasts.
• Since the speaker is equipped with individual offset adjustable volumes for each broadcasting modes and patterns (internal sound source), actual broadcasting volume can be normalized or optimized.
• Broadcasts can be controlled using Remote API or control inputs from connected external equipment.
• Connected external equipment can be controlled by control outputs in synchronization with speaker broadcasts.

ABOUT SECURITY MEASURES

• Ensure that sufficient security measures are taken on the customer’s own responsibility.
• TOA Corporation takes no responsibility for damage or loss caused by security-related problems, such as illegal access.
• To help prevent illegal access to the unit, be sure to change the user ID and password from those used for initial setup.
• For setting methods and other details, please refer to the separate receiving device setup manual which can be downloaded from the TOA DATA Library (https://www.toa-products.com/international/).
• Take utmost care in the management of the unit’s communications password.

DIMENSIONAL DRAWINGS

NOMENCLATURE AND FUNCTIONS

1. Line output signal indicator (green)
   Lights green when a signal is outputting from this speaker or Line output.

2. Line/Mic input signal indicator (green, red)
   Lights green when a signal is input to Line/Mic input. Lights red when the input signal level is too high.

3. Line/Mic input volume control
   Adjusts the volume level of the Line/Mic input. Rotate this volume control clockwise to increase the volume level and counterclockwise to decrease it.
   Set this volume not to make the Line/Mic input signal indicator (2) light up in red.

4. Status indicator (green, blue, yellow, red)
   Indicates the speaker’s operating status.

• System mute is a state in which this speaker is muted by the control from the transmitting deviceUnit Operation	Status Indicator
  System startup	Flashing green
  Broadcast standby	Continuously lit green
  Broadcasting	Continuously lit blue
  System mute*	Flashing red
  Initialization or firmware updating	Continuously lit yellow

  5. Reset key
     The speaker begins to restart when this key is clicked.
     Hold down this key until the Status indicator (4) lights yellow to initialize the speaker’s settings.

  6. DIP switch

  7. Line/Mic switch (Switch 1)
     Set this switch to MIC when connecting a microphone, and to LINE when connecting a general sound source device other than a microphone.
     Default setting: LINE

  8. PAD switch (Switch 2)
     Enables or disables the microphone input pad. When the input level is high, set the PAD to –20 dB. Default setting: 0 dB

  9. Phantom switch (Switch 3)
     Set whether or not to supply phantom power to the microphone connected to Line/Mic input terminals (10). Phantom power is a 12 V DC.
     Default setting: OFF

  10. Control input terminals
      Allows input of control signals from connected external equipment to enable actions set in the Event settings.

  11. Functional ground terminal
      If excessive noise is produced when the speaker is connected to external equipment, connect this terminal to the external equipment’s functional ground terminal, potentially minimizing the noise level.
      Note
      This terminal is not for protective ground.

  12. Control output terminals
      Allows control of external equipment in synchronization with the unit operation.

  13. Line/Mic input terminals
      Connects with a microphone or sound source device. This can be used as an audio input during SIP calls, or for monitoring VMS broadcast.
      Adjust with the switches of the DIP switch according to the output level of the connected device.

  14. Line output terminals
      Connects with an external amplifier etc. and outputs the same audio as the speaker output.

  15. LINK/ACT indicator (green)
      Flashes when data is being sent or received over a network.

  16. LAN port
      Connect to a PoE switching hub using a LAN cable.

SYSTEM EXAMPLE

SIP Broadcasting/Two-way Communication

VMS Broadcasting

HANDLING PRECAUTIONS

• Please apply the latest firmware version to this product. The latest version is available at the TOA DATA Library (https://www.toa-products.com/international/).
• As this product is IP-based, a slight time lag between actual and broadcast may happen.
• Broadcast audio may sometimes break up due to packet loss or network failure.
• Periodic inspection and manual rebooting are needed to extend the product life.
• This product may reboot automatically to keep the stable operation.

INSTALLATION PRECAUTIONS

CAUTION
Observe the following instructions when attaching the safety wire. Failure to do so could result in the speaker falling, potentially resulting in personal injury.

• Select a safety wire that is strong enough to withstand the total weight of the unit being mounted.
• Use a wire with a diameter larger than 1.5 mm or 0.06″.
• Attach the safety wire so that it does not become slack.

Notes

• Since the safety wire is not supplied with the IP speaker, be sure to prepare it separately.
• When attaching the safety wire, be sure that it is fastened securely to the safety wire attachment ring.

INSTALLATION

IP-A1PC580R

• Use back can HY-BC580U if UL 2043 (use in air handling spaces) is required.
• All wire entry knockouts should use metal conduit and metal fitting only. No rubber bushings on back can.

Connect the IP speaker to the PoE Switching hub using a LAN cable (straight UTP or STP cable, both rated at Category 5 or greater and fitted with RJ45 connectors).
Compatible switching hubs:
Switching hubs conforming to PoE (IEEE802.3 af Class 3) specifications.

IP-A1PC580S Connect the IP speaker to the PoE Switching hub using a LAN cable (straight UTP or STP cable, both rated at Category 5 or greater and fitted with RJ45 connectors).

Compatible switching hubs:
Switching hubs conforming to PoE (IEEE802.3 af Class 3) specifications.

CONNECTIONS

Connections to Line/Mic Input and Line Output Terminals
Use the supplied removable terminal plugs (6 pins) for connection. Use a 2-core shielded cable to connect the audio device. Also, set the DIP switches according to the audio device to be connected. For connection of the removable terminal plugs, see “Removable Terminal Plug Connections” on p. 12.

[LINE/MIC IN level adjustment]
Set roughly the volume of individual connected devices by DIP switch.
After that, use the Line/Mic input volume control for fine volume adjustments. Adjust the level so that the Line/Mic signal indicator lights green, not red .

Connections to Control Input and Output Terminals

• Use the supplied removable terminal plugs (6 pins) for connection. Connect a control line of 2 channels control input and 1 channel control output from the external control device to the IP speaker control input or control output terminal.
• For connection of the removable terminal plugs, see “Removable Terminal Plug Connections” on p. 12.
• The following functions can be assigned to the control input and control output terminals by browser settings:

| Assignable Functions
---|---
Control Input terminals|

• SIP device calls
• Internal sound source broadcasting
• Change the broadcasting volume (Mute or Offset)

Control Output terminals|

• SIP broadcast in progress output
• VMS broadcast in progress output
• Multicast broadcast in progress output
• Internal sound source broadcast in progress output

For settings, please refer to the separate receiving device setup manual. The latest version of the setup manual is available on the TOA DATA Library  ( https://www.toaproducts.com/international/ ).

Removable Terminal Plug Connections
Please note the following points when making connections to the control input or output terminals using the supplied removable terminal plugs:

• Do not tin stripped wire ends with solder. Soldered wire ends will be crushed when the terminal plug screws are tightened, leading to higher contact resistance and potentially resulting in an abnormal rise in the temperature of the connected parts.
• Use AWG 24 – 14 wire (ø0.5 – 1.6 mm solid wire or multi-stranded wire with a cross- sectional area of 0.2 – 2.0 mm2 ).
• Strip the wire end back about 7 mm (0.28″).
• When connecting 2 wires or a signal cable to a single terminal, crimp them in an insulated (twin) wire ferrule to prevent their core wires from being separated from one another.
• Use a ferrule of the dimensions shown in the figure as below.

Note
b: 0.8–1.1 mm (0.03″ – 0.04″) I2: 8 mm (0.31″)
Select dimensions “a” and “l1” depending on the wires to be used.

SETTINGS

System Settings Summary
The following settings can be performed using a PC browser connected to the same network as the IP speaker.

setting
Network| Network settings such as IP address
SIP| Settings of SIP connection enable/disable, SIP server address, authentication information, and audio codec
VMS Broadcasting| Settings of VMS connection enable/disable and authentication information, connection port settings
Multicast| Settings of multicast reception enable/disable, multicast address and port, and control output during multicast broadcast
Audio| Settings of speaker volume and input volume for individual broadcast classifications
Media| Uploading/downloading or deletion of sound source files such as messages to or from the internal memory
Pattern| Registration of sound source playback to be associated with events as patterns
Event| Settings of operations to be synchronized with the control input and control output
Priority| Settings of priority order for each broadcast mode; SIP broadcast, VMS broadcast, multicast broadcast and internal sound source broadcast
User| Changing username and password
Maintenance| Download and upload the configuration file, initialization, firmware update, hardware reboot and downloading action logs
System| Date and time settings, NTP server settings, language selection, time zone settings

• For more information, please refer to the separate receiving device setup manual.
• The latest version of the setup manual is available on the TOA DATA Library. (https://www.toa-products.com/international/)

System Requirements
Connectable system requirements are as follows:

11 Home
Browser| Microsoft Edge, Google Chrome

Notes

• Windows and Microsoft Edge are registered trademarks of Microsoft Corporation of the United States in the United States and other countries.
• Google Chrome is a trademark of Google LLC of the United States in the United States and other countries.

Connection with Browser

1. Connection presets
   The IP speaker is factory-preset as follows:

2. Username: admin

3. Password: guest

4. IP address: 192.168.14.1

5. Subnet mask: 255.255.255.0

6. Default gateway: 0.0.0.0
   Before connecting a PC to the IP speaker and changing its setting, it will be necessary to set the PC’s network settings so that it can operate on the same network as the IP speaker. Take care that no IP addresses are duplicated in the same network. For example, if the IP speaker’s IP address is 192.168.14.1, set the PC’s IP address to 192.168.14.10.

7. Making connection
   Notes
   Avoid simultaneously connecting to the IP speaker from multiple PCs.
   Avoid simultaneously connecting to the IP speaker from a single PC using multiple browsers.

8. Step 1. Start the browser and enter the speaker’s IP address in the address field. The Login screen is displayed.

9. Step 2. Enter the username and password, and click the LOGIN button.
   The Status screen is displayed, enabling a range of settings.

Note
For details regarding the setting method, please refer to the separate receiving device setup manual. The latest version of the setup manual is available on the TOA DATA Library. ( https://www.toaproducts.com/international/ )

INITIALIZATION OF SETTINGS

Follow the procedure below to return all IP speaker settings to their default:

Tip
When initialized with the Reset key, the IP speaker’s sound source files are left in “Media”, not deleted. Initialization to factory defaults, including deletion of sound source files, should be performed using the browser settings menu.

1. Step 1. Connect he unit to the PoE switching hub using a LAN cable. The IP speaker will be started.

2. Step 2. Hold down the Reset key located on the top panel using a pointed tool. The IP speaker automatically restarts and settings initialization begins.
   Tip

3. Clicking on the Reset key causes the IP speaker to be restarted.

4. If pressure on the Reset key is released part way through the initialization process, only unit restart will be performed, and the settings will not be initialized.

5. To click on the Reset key, use a tool that is thinner than ø1.5 mm (0.06″) and longer than 5 mm (0.2″).

6. Step 3. When the status indicator lights yellow, release the reset key.
   When initialization is complete, the status indicator lights green and all settings will be initialized to their default settings.
   [Default Settings]

7. Username: admin

8. Password: guest

9. IP address: 192.168.14.1

10. Subnet mask: 255.255.255.0

11. Default gateway: 0.0.0.0

CAUTIONS REGARDING THE AVC/H.264 PATENT LICENSE

• TOA’s IP-A1PC580R/A1PC580S IP speakers employ MPEG technology (AVC/H.264 Standard) regarding the handling of image information. TOA Corporation has received approval to use this technology from MPEG LA, LLC, the patent management group.
• Please note that the use of this product is prohibited except the following cases:
  • The use of the product is intended for personal use of a user of the MPEG technology and also for nonprofit use, which includes (i) video encoding conforming to the AVC/H.264 Standard (hereinafter referred to as “AVC/H.264”) and/or (ii) personal use and decoding of AVC/H.264 encoded by an MPEG technology user engaged in non-profit activities and/or AVC/H.264 furnished by a video provider who is granted a license by MPEG LA, LLC.
• Regarding use for sales promotion or commercial purposes, or additional licensing information, please contact MPEG LA, LLC (https://www.mpegla.com).

OPEN SOURCE SOFTWARE

• This product uses software based on open source software license(s).
• If you need further information about the original open source software including source code, please download it from the TOA DATA Library (https://www.toa-products.com/international/).
• Please note that we cannot answer any questions about the contents of the original source code.
• This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit ( http://www.openssl.org/ ).
• This product includes cryptographic software written by Eric Young ( eay@cryptsoft.com .

ACCESSORIES

• Pattern paper ………………………………………………… 1
• Removable terminal plug (6 pins) …………………….. 2
• Machine screw 5 x 38 ……………………………………… 4

Tip
The specifications of this product are available in TOA DATA Library (https://www.toa-products.com/international/).
Scan the QR Code at right with your mobile phone camera to access the WEB site and search for this product number (IP-A1PC580R or IP-A1PC580S).

Traceability Information for USA
TOA Electronics, Inc.
1 Harmon Plaza, Suite 700 Secaucus, New Jersey 07094, USA
https://www.toaelectronics.com/
https://www.toa-global.com/en

References

• products.com
• /index.html
• TOA DATA Library
• TOA Electronics, Inc. - Professional Audio Equipment Manufacturer

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>