TOA Electric 900 Series Power Amplifier Instruction Manual

TOA 900 SERIES
POWER AMPLIFIER P-924A
Operation Instruction Manual

Features

1. Wide frequency response; 20 — 20,000 Hz, ±1dB
2. Low distortion and noise level
3. Excellent output regulation
4. A full range of plug-in modules
5. Self-protecting circuitry design
6. Varied output impedances; 4 and 8 ohms, 25 and 70 volts
7. Input level switch (selectable 1,000mV/100mV)
8. Portable or rack-mounting type

General Descriptions

The TOA P-924A Power Amplifier delivers up to 240 watts of power at less than 0.5% total harmonic distortion (THD) from 20 to 20,000 Hz (transformerless 4-ohm output). The P-924A has a highimpedance direct input and an input port (edge connector) to accept one module accessory. Module selection is determined by application among the TOA plug-in modules:
The M-01 series, M-03 series, M-51 series and M-61 series Microphone Preamplifiers, R-01 Mag. Phono Preamplifier, the U-01 series, U-21 series and U-61 series Auxiliary Preamplifiers for high-level sources, the B-01 series Bridging Transformers for bridging high impedance lines, the L-01 series Line Matching Transformers for matching 600-ohm lines, and the S-01, S-02 and S-03 Tone signal generators for generating attention-getting signals and 1 KHz sine wave for testing within the total system.
The P-924A has a low-cut switch for cutoff frequency of 60 Hz, and an input- level switch for input sensitivity of 1V (0dBv) or 100mV (—20dBv). Output terminals provide connections for 4-ohm and 8-ohm speakers, plus 25-volt and 70-volt speaker distribution outlets.
With plug-in modules, the TOA P-924A Power Amplifier may be used as a pre/power amplifier.
The P-924A can be rack mounted by using the MB-931A Rack mounting Bracket accessory. The PF-911 Perforated Panel (1.73 inches, 1 rack unit) accessory provides suitable ventilation, finished in color to match the P-924A.

Front Panel Controls and Features

on-off modes.
2| METER| Indicates the output level of the amplifier. At rated output, it shows 0 VU (at continuous sine-wave signal input).
When power is turned on, meter illuminates.
3| INPUT VOLUME CONTROL| Adjust gain of INPUT.
4
5| PROTECTION INDICATOR (RED)
NORMAL INDICATOR (GREEN)| This LED indicator comes on and goes out in about 5 seconds after the power switch is turned on.
If the LED indicator remains lit indicating that a muting relay is not activated, turn the power switch off after disconnecting the speaker line and turn it on again. As a result,
1.if the LED indicator goes out in about 5 seconds, the speaker line may be short-circuited or overloaded.
Check the speaker line.
2.unless the LED indicator still goes out, abnormality has occurred in the power amplifier stage.
Check the power amplifier stage.
Lights up when the amplifier is normally working.

Rear Panel Controls and Features

power consumption of up to 500W.
3
4
5| AC FUSE
DC FUSE (-)
DC FUSE (+)| Protects amplifier from excessive current drain. Replace only with same type fuse.
Refer to qualified service personnel if fuse blows repeatedly.
AC FUSE| 250V 7A
DC FUSE (-)| 250V 8A
DC FUSE(+)| 250V 8A
6| OUTPUT TERMINALS| Connect to speakers.
7| MODULE INPUT
PORT| Accepts PLUG-IN MODULES which are optionally available. Module selection is determined by application.
8| LOW-CUT SWITCH| Cuts off unnecessary low frequency.
9| INPUT
LEVEL SWITCH| Selects input sensitivity. Place in “1V (Od B v)” position when normally used as a power amplifier. …
Note: The position of INPUT-LEVEL SWITCH should be changed according to modules used or equipment connected to DIRECT INPUT TERMINAL.
10| DIRECT
INPUT TERMINAL| Connects directly to external equipment without using modules. Unbalanced 10k ohms.
11| EARTH TERMINAL| Normally connects to a record player’s ground.

Input Connections

• Two types of input terminals are provided on the rear for input connections.
  (1) 2P terminal (marked HOT, E)
  It is provided for direct input (unbalanced, 10k ohms) without using plug-in modules. This terminal is directly connected with a potentiometer inside.
  (2) Plug-in module input
  Select the desired modules according to application.

• DIRECT INPUT TERMINAL and) MODULE INPUT are not usable simultaneously.

  • Plug the module into INPUT PORT, sliding it between the guide rails, and secure with two screws.
  • When INPUT PORT is not occupied, cover the PORT with the blank panel, and secure it with screws.
  • Be sure that INPUT-LEVEL SWITCH is in the proper position for the modules used or the equipment connected to DIRECT INPUT TERMINAL.
  • When the P-924A is used in combination with a mixer preamplifier or serves as an incremental power amplifier, normally place INPUT LEVEL SWITCH in “1V (0dBv)” position.

Output Connections P-924A

The speaker outputs of the amplifier are 4 Ω 8Ω 25V and 70V.
Connect speakers to one of these outputs.
Class 2 wiring may be used.
Since these outputs consist of 8Ω 25V and 70V via the output transformer (matching transformer) and direct output of 4 Ωthe connecting method differs in each case. See the following diagrams.
Note : Impedances indicated below imply total speaker system (load) impedance.
When connecting speakers to any one of the outputs of 8Ω 25V or 70V (BALANCED TRANSFORMER OUTPUT);

CAUTION ‘Modules: should not. be inserted or removed while the amplifier is-turned-on.

Plug-in Modules and Input Level SW Setting

Plug-in Modules| Model
No.| Input level SW Setting
---|---|---
1V (0dBV)| 100mV
(—20dBV)
Balanced low impedance microphone preamp. module (with presentable low-cut filter, high-cut filter and gain controls)| –| M-01| —| Ο
Remote Volume control| M-21
Voice Gate| M-51
Compressor| M-61
Unbalanced high impedance microphone preamp module (with presettable low-cut filter, high-cut filter and gain controls)| —| M-03| —| Ο
Equalized mag phono preamp module(with presettable gain control)| –| R-01| —| Ο
Unbalanced high impedance auxiliary preamp. module (with presettable gain control)| –| U-01| —| Ο
Remote Volume control| U-21
Compressor| U-61
Balanced 10K2 bridging transformer module| —| B-01| Ο| Ο
Balanced 6000 bridging transformer module| —| L-01| Ο| Ο
Signal tone generator module (with presettable output level control)| 1 kHz Sine Wave| S-01| —| Ο
Yelp and buzzer| S-02
One-tone chime and continuous one-tone chime| S-03

*See PLUG-IN MODULES for detail.

Note:
In this case, the LOW-CUT SWITCH should be “CUT” position.
This amplifier is characteristically flat even in the low frequency range.
Therefore, in TRANS OUTPUT, the acoustic effect and frequency-response characteristics may be altered. In TRANS OUTPUT, cut off unnecessary low frequency to obtain the best acoustic condition.

When connecting speakers to the 4Ω DIRECT OUTPUT); output. (UNBLANCED

Installation

• Do not block cover ventilation holes.
• The amplifier should not be placed in areas;

1. with poor ventilation
2. exposed to direct sunlight.
3. with high ambient temperature or adjacent to heat-generating equipment.
4. with high humidity or dusty levels.
5. susceptible to vibration.

CAUTION Do not remove the case or you may encounter an electric shock

Operation

When all connections are completed, turn power switch on. Then, the meter is illuminated. Approx. 5 seconds after switching power on, the amplifier comes into operation.
ADJUSTMENT OF VOLUME CONTROL
Adjust the input volume control to obtain appropriate output level. In normal use of BGM playing or announcement, the deflection of the meter is recommended to be within the range as indicated in the drawing. Tone quality will be considerably deteriorated if the pointer indicates around 0 VU.

The pointer of meter indicates 0 VU if continuous signals like sine waves are applied to the input of the amplifier.

When the power amplifier is used in combination with a mixer preamplifier, adjust the total gain at the mixer preamplifier with the gain setting of the power amplifier at maximum.

Rack Mounting

To mount the amplifier in a standard 19-inch equipment rack, use the MB-931A Rack-mounting Bracket accessory.

Fix the MB-931A with attached 4 screws.
The length of the screws should not exceed 12mm (1/2 inches).

If two or more amplifiers are mounted in an equipment rack, space should be provided between the units for ventilation.
The PF-911 Perforated Panel is recommended for this purpose.

Servicing

• Unpacking
  Upon receipt of the amplifier shipment, please inspect for any damage incurred in transit. If damage is found, please notify your local TOA representative and the transportation company immediately.
  State date, nature of damage, whether any damage was noticed on the shipping container, prior to unpacking. Please give waybill number of shipping order.

• Failure
  Should amplifier fail, contact your nearest TOA authorized contractor or service center.

Specifications

| P-924A
---|---
Type| Power amplifier
Output| (D) 240W  RMS
(T) 220W  RMS
Power Band Width| (D ) 20-20,000  H z, 0.5%  T HD
(T) 50-20,000  Hz, 0.5%  THD
Frequency Response| (D) 20  -20,000  Hz,±1 dB
(T) 2 0 – 15,000  Hz,±1  dB
( T ) 2 0 -20,000 Hz ,-3dB
Total Harmonic Distortion| 0.01% at 1 kHz, rated output
inputs| One Input Port : Port accepts any input module except T-01 , which cannot be used.
One Direct Input Note : Use of direct input prohibits use of modular input port.
Input Sensitivity/Impedance| Input Port : 100 mV or 1 ,000 mV (Switchable)/10k ohms
Direct Input : 100 mV or 1 ,000 mV (Switchable)/10k ohms
Outputs
(D) = Direct
(T)  =  Transformer| Main (T): 8 ohms, 25 & 70 volts, balanced
Main (D): 4 ohms, unbalanced
Output Regulation (1 kHz) .| (D) Less than 0.5 dB, no load to fu l l load (T) Less than 1 .0 dB, no load to full load
Signal to Noise Ratio (Band Pass20 — 20,000 Hz)| Input level switch in 0 dBv (1 ,000 mV) position : 105 dB
Input level switch in —20 dBv (100 mV) position : 90 dB
Controls| 1 Input gain control
1 Input level switch
1 Power ON/OFF switch
1 Low-cut switch (60 Hz, 6 dB/octave)
Indicator| 1 Illuminated VU meter, 2 LED for protection circuit
Protection| Self-protection, with 2 AC fuses (1 inside) and 2 DC fuses
Connectors| Inputs…….Card-edge connector and screw-terminal strip
Output……Screw-terminal strip
AC output…………..3-pin grounding type
AC power cord/plut …….SJT, 3-prong type
Temperature Range| AC 120 vol ts, 60 Hz, 3A
Dimensions in mm (inches) (high) x (wide) x (deep)| 150.5 (5.92″) x 420 (16.54″) x 333 (13.11″)
Rack-mounting space size “3U” (5.21″)
Weight (without input modules)| 19.5kg (43 Ibs.)
Color.| Silver
Other Features| Output disconnected for approx. 5 sec. after switching power on.

*Specifications are subject to change without notice.

Block Diagram P-924A

Plug-in Modules

The TOA PLUG-IN MODULES are suitable for TOA 900 SERIES MIXER POWER AMPLIFIERS A-901A, A-903A, A-906A, and A-912A MIXER PREAMPLIFIER M-900A, POWER AMPLIFIERS P-906A, P-912A, P924A, and IN-WALL
AMPLIFIERS W-906A, W-912A.
Owing to wide selection of types of connectors can also meet the needs of equipment to be connected. MICROPHONE PREAMPLIFIER M-01 series, M-51 series, M-61 series, M-03, M-11 and M-21 incorporates controls for high-cut, low-cut and gain. A gain control is built in MAG. PHONO PREAMPLIFIERS R-01, and AUXILIARY PREAMPLIFIERS U-01 series, U-11 series, U-12, U-21 and U-61, LINE OUTPUT T-01 and AUX INPUTLINE OUTPUT T-02.
M-61 and U-61 are built-in compressor circuit to protect the output level from distortion as a result of excessive input and keeps it constant. M-51 series is built-in voice gate circuit to be automatically activated by presence of signal.
U-12 can adjust mute level.
T-01 series is an output module with transformer, serving as a line output for recording, etc…
A group of special signal generating modules is also available for catching- attention before announcement and testing within the total systems. ALL PLUG- IN MODULES have handles on their front for easy insertion and removal.

FEATURES

1. Wide dynamic range
2. Low noise and distortion
3. Wide frequency response
4. Built-in remote volume control circuit (M-21)
5. Built-in remote master volume or remote volume control circuit. (U-21)
6. Built-in muting circuit to mute incoming signal when MUTE TERMINAL is grounded, (available for modules having 10’s in its model number such as U-11.)
7. Built in muting circuit to deliver or mute its output signal when MUTE TERMINAL is grounded. (M-11)
8. Built-in signal activated muting function (L-41)
9. Presettable gain control (except for B-01, B-11, L-01 and L-11)
10. Microphone modules furnished with tone controls (M-01, M-11, M-21, M-51, M-61, and M-03)
11. Built-in voice gate circuit (to be activated by input signals.) (M-51 series.)
12. All the microphone modules (except M-03) come with phantom powering capability.
13. Built-in compressor circuit (M-61, U-61)
14. Built-in variable muting circuit to adjust the muting level. (U-12)

• FRONT PANEL CONTROLS AND FEATURES
  Modules with built-in controls are provided in the following six types.GAIN CONTROL| This adjusts gam. Turn clockwise (CW) to increase and counter- clockwise (CCW) to reduce gam
  Set the gam as low as possible, thereby, noise can be reduced, and the maximum permissible input level is raised.
  ---|---
  THRESHOLD (M-61)| This adjusts threshold level of compressor.
  Turn clockwise (CW) to reduce threshold level (to activate the compressor with lower input signal
  level).
  OUTPUT GAIN (T-02)| This adjusts gam of the line output. Turn clockwise (CW) to increase and counterclockwise (CCW)
  to reduce gam regardless of setting position of the input gam adjust knob.
  NOMINAL POSITION MARK| The left figure shows nominal setting of controls.
  LOW-CUT FILTER CONTROL
  330Hz, 6dB/oct (max. attenuation)| This provides flat characteristics at full CW position and attenuation in low frequency by turning CCW. Adjust it to obtain proper tone quality. With low-cut, tone becomes clear.
  MUTE LEVEL (U-12)| This adjusts mute level. Turn clockwise (CW) to increase mute level (to be muted excessively) and counterclockwise (CCW) to reduce mute level.
  INPUT GAIN (T-02)| This adjusts input gam from AUX. Turn clockwise (CW) to increase gam and counterclockwise (CCW) to reduce.
  HIGH-CUT FILTER CONTROL 4.2kHz, 6dB/oct (max. attenuation)| This provides flat characteristics at full CW position and attenuation in high frequency by turning CCW. Adjust it to obtain proper tone quality. With high-cut, tone becomes soft.
  SENSITIVITY (M-51)| This adjusts sensitivity for voice gate. Turn clockwise (CW) to increase sensitivity (to open the gate at full CW position regardless of any input level) and counterclockwise (CCW) to reduce sensitivity.

SPECIFICATIONS IN COMMON

CAUTION: *Modules model M-11 U-12 should be used be used exclusively with model A-901A A-306A A-912A M-900A W-906A and W-912A.

Plug-in Modules

“Jumper Wire Setting”
M-01, 11, 21, 51, 61
All the microphone modules come with phantom powering capability. Into desired, cut J1 on the board.
U-21
Cut J2 on the board to use as a remote master volume control unit Leave J2 on to use as a remote-control AUX module.
U-61
Cut J2 on the board to use as a compressor unit which goes between PREAMP OUT and POWER AMP IN (LINK IN/OUT).
M-11
Either (both) J3 or (and) J4 is (are) to be cut for a proper operation.
Refer to the table below.

terminals are closed
on| cut| Normally “On”, becomes “Off” when muting
terminals are closed.
cut| cut| Works as a regular microphone input module.

^Z: Impedance Mute: Normally “On”, becomes “Off” when muting __ terminals are closed.
Mute: Normally “Off”, becomes “On” when muting terminals are closed.

Accessories

Operation and Connections

(Plug-in Modules)

• S-01 (1 ,000Hz SINE WAVE)

• S-02 (YELP AND BUZZER)
  CONNECTIONS

• S-03 (ONE-TONE CHIME AND CONTINUOUS ONE-TONE CHIME)
  CONNECTIONS

Block Diagrams (Plug-in Modules)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>