Cylinda TS3190VPH Drying Cabinet User Manual

Cylinda TS3190VPH Drying Cabinet

Product Information

• Specifications:
  • Dimensions: 1945mm x 597mm x 615mm
  • Power Supply: 230V, 10A
  • Protection Class: IP24
  • Drying Levels: 5 levels
  • Drying Time: Up to 8 hours
  • Power Consumption: 900W
  • Capacity: 16m³, 4kg (dry weight)
• Product Description:
  • The product is a drying appliance designed for home use. It features multiple drying levels and modes for efficient drying of clothes.

Product Usage Instructions

• Safety Information:
  • Before using the appliance, ensure that it is properly installed and that the power plug is easily accessible. Always follow safety precautions to prevent accidents.
• Operating Panel:
  • The operating panel contains various indicators and buttons to control the drying process. Make sure to select the appropriate drying level and mode based on your laundry needs.
• Cleaning and Maintenance:
  • Regularly clean the filters to ensure optimal performance. Do not drink or use the condensation water for cooking. In case of any issues, refer to the troubleshooting section in the manual.

FAQs

• Q: What should I do if the appliance does not work at all?
  • A: Check if the power supply is connected and the filters are clean. Reset the appliance and try again.
• Q: Why does the alarm indicate that the condensation water tank is full?
  • A: The filters might be clogged. Clean the filters as instructed in the manual to resolve this issue.
• Q: What should I do if three setting indicators are blinking?
  • A: This could indicate an overheating issue. Make sure the appliance is properly ventilated and not overloaded.

CUSTOMER CARE AND SERVICE

• We recommend using original spare parts.
• Have the following information available when contacting the service department: Model, PNC, and serial number.
• This information is on the nameplate.
• Warning/important safety information General information and tips.
• Environmental information
• Subject to change without notice.

SAFETY INFORMATION

• Carefully read the enclosed instructions before installing and using the machine.
• The manufacturer is not responsible for any personal injury or other damage resulting from improper installation or use.
• Always keep the manual in a safe and accessible place for future reference.
• Read through the safety instructions.

Safety for children and disabled people

• A RISK of suffocation, injury, or permanent disability
• This product can be used by children from 8 years of age and above, and by persons with reduced physical, sensory, or mental capabilities, as well as sons with limited experience and knowledge, if they are supervised or instructed on how to use the product safely and understand the
• risks associated with its use.
• Do not allow children to play with the product.
• Children under 3 years of age should not be in the vicinity without constant supervision.
• Keep all packaging materials out of the reach of children.
• Keep children and pets away from the product when the door is open.
• If the product has a child lock, we recommend that you activate it.
• Cleaning and user maintenance should not be carried out by unsupervised children.

Public safety

WARNING! The product is designed to dry only water-washed textiles.
CAUTION! To avoid danger due to inadvertent resetting if a fuse has blown, this product must not be used with an external switching device such as a timer, or connected to a circuit that is regularly switched on and off. on and off.

• Do not change the specifications of the product.
• Connect the plug to the power socket only at the end of the installation. Make sure that the plug is accessible after the product has been installed.
• Make sure you have good ventilation in the room to avoid gases being sucked back into the room from products using gas or other fuels, such as fireplaces.
• If the power cord is damaged, it must be replaced by the manufacturer, the manufacturer’s authorized service center or suitably trained persons to avoid electrical hazards.
• Do not exceed the indicated maximum wash load of 4kg ( “Technical data”)
• Do not use the product if items have been soiled with chemicals.
• Garments stained by cooking oil, acetone, alcohol, petrol, kerosene, stain removers, turpentine, wax, and wax removers should be washed in hot water with extra detergent before being dried in the drying
• Do not dry laundry containing foam rubber (latex), shower caps, waterproof textiles, garments with rubber inserts, and clothes or pillows with foam rubber filling in the drying cabinet.
• Fabric softeners and similar products should be used according to the manufacturer’s instructions.
• Remove all objects from the product that can catch fire, such as lighters or matches.
• Switch off the product and disconnect it from the mains before maintenance.

SAFETY INSTRUCTIONS

Installation

• Remove all packing materials.
• Installation
• Follow the installation instructions provided with the product.
• Do not install or use the appliance where there is a risk of frost or where it is exposed to heat (e.g. direct sunlight, moisture and dusty places).
• The room or place where it will be installed must be well-ventilated.
• Use a spirit level to check that the product is completely horizontal when it is in the place where it will be used. If it is not, you can adjust your feet until it is.
• The product is heavy, so always be careful when moving it. Always wear protective gloves.
• When moving the product, lift it by the front edge so as not to scratch the floor.
• Wait at least one hour before plugging the product into the wall socket when it is lying down.

Electrical connection
WARNING: Risk of fire and electric shock.

• Connect the plug to the power socket only at the end of the installation. Make sure the plug is accessible after installation.
• The product must be grounded.
• Check that the product’s ratings match your power source. If not, consult an electrician.
• Always use a properly installed, shockproof, and grounded electrical outlet.
• Do not use power strips or extension cords.
• Do not pull the power cord to disconnect the product from the electrical outlet. Always grasp the plug.
• Do not touch the power cord or plug with wet hands.
• United Kingdom and Ireland only. This product is equipped with a 13 A mains plug. If the fuse in the plug needs replacing, a 13 A ASTA (BS 1362) fuse should be used.
• This product fulfills the requirements of the EU Directive.

Usage

WARNING: There is a risk of personal injury, electric shock, fire, or damage to the product.

• This product is for domestic use only.
• Do not dry soaked garments in the tumble dryer.

Maintenance and cleaning

WARNING: There is a risk of personal injury, electric shock, fire, or damage to the product.

• Do not spray water or steam on the product to clean it.
• Clean the product with a damp, soft cloth. Use only neutral detergents.
• Do not use abrasive products, scouring pads, solvents, or metal objects.

Divestment

WARNING: Risk of suffocation or injury.

• Unplug the product from the electrical outlet.
• Cut the power cord near the product and discard it.
• Remove the door latch (if present) to prevent children or pets from being trapped in the drying cabinet.
• Dispose of the product per local regulations for WEEE (Waste Electrical and Electronic Equipment) disposal.

PRODUCT DESCRIPTION

1. Control panel
2. Hangers
3. Lint filter
4. Condensation water tank
5. Adjustable foot
6. Drain hose
7. Mains cable
8. Air inlet filter
9. Protective plate
10. Door (reversible)

INSTALLATION

• It is recommended that the drying cabinet is placed on a drainage plate unless it is located in a bathroom or laundry room. This makes it easier to detect a possible leak.

Placement

• Ensure that the drying cabinet is level where it is installed. Tilt the drying cabinet slightly to raise the feet a few centimeters. Adjust the feet with a 17 mm spanner.
• The door adjustment is dependent on the product being level.

Fixing to the wall

• The cabinet should be fixed to a wall to prevent tipping.
• Install the two angle brackets on the product as follows:

1. Ensure that the drying cabinet is level where it is installed.
2. Screw the brackets to the top of the product. The brackets have grooves for adapting to the wall.
3. Attach the product to the wall.

Installing the drying cabinet hangers

Place the drying cabinet hangers in their holders. If necessary, the hangers can be lowered by lifting them straight up from their holders and folding them down towards the rear wall.

Drainage hose

• To avoid emptying the condensate tank, the appliance can be connected to the sewerage system.
• If the distance between the appliance and the drain exceeds 0.2 meters, a drain kit must be used. It can be ordered from Distriparts.

Re-hanging the door

WARNING:

• Disconnect the plug from the power socket before starting the work.
• It is recommended that two people perform the door hanging.

1. upper tray
2. upper hinge
3. Lower hinge
4. Lower tray

1. Unscrew the lower hinge turn it to the left and remove it. Remove the door.
2. Unscrew the lower hinge bracket and install the threaded washer on the opposite side.
3. Unscrew the upper hinge.
4. Unscrew the upper hinge bracket (part of the front panel) and install the threaded washer on the opposite side.
5. Install the lower hinge on the opposite upper side.
6. Replace the door on the top hinge.
7. Install the upper hinge on the opposite lower side.
8. Unscrew the handle. Remove the cover plugs on the opposite side by using a 3 mm mandrel or drilling into them. Install the handle. Attach the cover plugs found in the accessory bag.

Finally, check the following:

• That all screws are tightened.
• The magnetic seal sucks firmly against the cabinet.
• The doors open and close properly.
• If you do not wish to carry out the above measures, you can contact your nearest authorized service workshop.
• The service technician will turn the door for a fee.

CONTROL PANEL

DRYING PROGRAMME

• AUTO MODE
  • Drying is switched off automatically when the selected level of dryness is reached.
• TIMER MODE
  • Drying is switched off when the selected time is reached.
  • The door must be closed before the drying program can start.
  • Changing the drying program once a drying program has started is not possible. To change the drying program, the  Start/Stop button must be pressed. and another program selection must be made

DAILY USE

Turn off the drying program:

• Last used drying program:

1. Press the main power switch to position 1 (the control panel displays the last used program).
2. Press the Start/Stop button. Select another drying program:

• Automatic mode:

1. Press the program button until the Auto Mode so indicator appears.
2. Press the program setting button to select the drying level.
3. Press the Start/Stop button. The drying program **∫∫∫** indicator lights up. When the drying program is finished, the drying program **∫∫∫** indicator turns off and the drying program completion indicator turns on.

• Timer mode:

1. Press the program button until the Timer indicator appears.
2. Press the program setting button to select the drying time.
3. Press the Start/Stop button. The drying program **∫∫∫** indicator lights up. When the drying program is completed, the drying program **∫∫∫** indicator goes out and the drying program completion indicator lights up.

Switching off the drying program

• To manually interrupt the drying program, press the Start/Stop button.
• To restart the drying program, press the Start/Stop button again.

The indicator for the condensation tank is full

• The condensation water tank is full indicator lights up when the tank is full.
• If this indicator continues while a program is running, the program will stop until the water tank is emptied and installed correctly. See “Maintenance and cleaning”.
• Once the water tank has been replaced, the program will resume after a short delay.

The indicator for cleaning the filters

• The filter cleaning indicator lights up when the filters need to be cleaned.
• See “Maintenance and cleaning”. After cleaning the filters, press the O. alarm reset button.

Open door indicator

• If the door is opened during a drying program, the » indicator flashes. If the door is left open for more than 30 minutes, the program is paused.
• When the door is closed, the indicator stops flashing, and the program resumes.

Overheating indicator

• The overheat protection will be right up if the system is overheated, see “Troubleshooting”. The system requires some time to cool down before the alarm can be reset by pressing the alarm reset button. After resetting, press the Start/Stop button to start again.

TIPS

• All types of laundry, wet clothes, shoes, and equipment can be dried in a drying cabinet.
• Laundry shall be hung up to dry in a way that allows air to circulate effectively.
• The laundry should be evenly distributed throughout the drying cabinet.
• Do not fill the hangers with too much laundry. Use more than one hanger for heavier garments.
• With this drying cabinet, you can control not only the temperature but also the level of dryness. Therefore, the drying cabinet has a moisture sensor to provide optimal drying results, regardless of the type of fabric or garment to be dried.
• For maximum efficiency, avoid opening the door during drying.

MAINTENANCE AND CLEANING

WARNING!

• Disconnect the plug from the socket before starting work.
• Use only water and a mild detergent to clean the drying cabinet.

CAUTION!!

• Never use volatile solvents
• If water accumulates on the bottom of the drying cabinet, it should be removed with a sponge or cloth.
• The protective plate and bottom of the drying cabinet should be kept as clean as possible at all times.
• Usually, it is dry and can be cleaned with a vacuum cleaner.

Cleaning the filters
The filters collect all the lint that accumulates during drying. To ensure that the drying cabinet works perfectly, the air filter and lint filter must be cleaned at least when indicated by the product.

• The lint filter can be accessed by lifting the cover plate.
• Clean the filter with a damp cloth.
• The air filter is accessed by pulling the corners of the frame outwards.
• Rinse the filter under running water.

CAUTION! Never use the drying cabinet without a lint filter or with a damaged or blocked filter.

Emptying the condensation tank

• It is recommended to empty the condensation water tank after each drying operation.

WARNING!

• The condensation water is not suitable for drinking or cooking.
• Remove the tank by pulling it outwards.
• Empty the tank through the open lid (A).
• Install the tank by pushing it in.
• The tank is correctly installed when it is flush with the front panel above.

TECHNICAL DATA

• Height 1945 mm
• Width 597 mm
• Depth 615 mm
• Mains voltage 230 V
• Fuse 10 A
• IP classification IP 24
• Moisture control 5 levels
• Timerkontroll 8 hours
• Maximum total power 900 W
• Total hanging length 16 m
• Capacity 4 kg (dry weight)

TROUBLESHOOTING

Replacing the bulb.

• The product has an interior light consisting of a long-life LED lamp.
• Only service personnel may replace the bulb.
• Contact an authorized service center.

ENVIRONMENTAL PROTECTION

• Recycle materials with the symbol . Recycle the packaging by placing it in a suitable container.
• Help protect our environment and our health by recycling waste electrical and electronic products.
• Do not throw away products labeled with the symbol with household waste.
• Return the product to the nearest recycling center or contact the local authority office.

CONTACT

• Service: Nationwide service in Sweden
• Visit www.cylinda.se.
• Call 0771-25 25 00
• Declare: Model code, Serial number,
• Purchase date, Problem description,
• Name and address, Phone number
• Contact us:www.cylinda.se.
• Elektroskandia Sverige AB, Cylinda, 191 83 Sollentua

References

• Prisvärda svenska vitvaror- Cylinda - En enklare vardag

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>