Cylinda Nova Trend SF 40 RFA Quality Cooker Hood User Manual
- May 15, 2024
- Cylinda
Table of Contents
Cylinda Nova Trend SF 40 RFA Quality Cooker Hood
Product Specifications
- Model : Nova Trend SF40RFA E 90 045 04 / Nova Trend SF40SVA E 90 045 05
- Connection Type : Ducting version / Filter version
- Dimensions : 16cm x 16cm x 16cm
- Installation Requirements : Minimum distance of 50cm from electric cookers and 65cm from gas or mixed cookers
Product Usage Instructions
Installation
Before installing the cooker hood, ensure that the minimum distance requirements are met based on the type of cooker being used.
Electrical Connection
Follow the electrical connection instructions provided in the manual. Ensure proper grounding and connection to a suitable power source.
Operation
Use the provided buttons to control the cooker hood functions. Familiarize yourself with the timer settings for efficient operation.
Maintenance
Regularly clean the grease filter to ensure optimal performance. Refer to the manual for instructions on replacing the bulbs when needed.
FAQ
- What should I do before using the appliance?
- Before using the appliance, carefully read the manual for important information on installation and operation.
- How should I dispose of the appliance?
- Do not treat the appliance as household waste. Follow local regulations for proper disposal or recycling of electrical and electronic equipment.
Dear Customer,
Thank you for choosing this high-quality cooker hood made by Cylinda. Please read this manual carefully. In it you will find important information that will help you to install and use this appliance in a proper manner resulting in long-term reliable operation of the device.
Symbols appearing in these instructions have the following meanings:
Important information concerning the proper operation of the appliance and your personal safety.
Ducting version
Information on how to protect the environment
Filter version
Before using the appliance, please carefully read this manual!
This manual applies to the following products
- Nova Trend SF40RFA E 90 045 04
- Nova Trend SF40SVA E 90 045 05
The hood can look different to that illustrated in the drawings in this
booklet. The instructions for use, maintenance, and installation, however,
remain the same.
Closely follow the instructions set out in this manual. All responsibility,
for any eventual inconveniences, damages or fires caused by not complying with
the instructions in this manual, is declined. The extractor hood has been
designed exclusively for domestic use
- It is important to conserve this booklet for reference at any moment. In case of a sale, cession or move, make sure it is together with the product.
- Read the instructions carefully: there is important information about installation, use, and safety.
- Do not carry out electrical or mechanical variations on the product or on the discharge conduits.
Note : the elements marked with the symbol “(*)” are optional accessories
supplied only with some models or elements to purchase, not supplied.
For technical drawings please turn to page 6 to find your product
Before the installation
Caution
WARNING! Do not connect the appliance to the mains until the installation
is fully complete. Before any cleaning or maintenance operation, disconnect
the device from the power supply by removing the plug or switching off the
power circuit.
Always wear work gloves for all installation and maintenance operations.
The appliance is not intended for use by children or persons with impaired physical, sensorial or mental abilities, or if lacking in experience or knowledge, unless they are under supervision or have been trained in the use of the appliance by a person responsible for their safety. This appliance is designed to be operated by adults, children should be monitored to ensure that they do not play with the appliance.
Never use the hood without effectively mounted grating!
The hood must NEVER be used as a support surface unless specifically
indicated.
The premises where the appliance is installed must be sufficiently ventilated
when the kitchen hood is used together with other gas combustion devices or
other fuels.
The ducting system for this appliance must not be connected to any existing
ventilation system which is being used for any other purpose such as
discharging exhaust fumes from appliances burning gas or other fuels.
The flaming of foods beneath the hood itself is strictly prohibited.
The use of exposed flames is detrimental to the filters and may cause a fire
risk, and must therefore be avoided in all circumstances. Any frying must be
done with care in order to make sure that the oil does not overheat and
ignite.
Accessible parts of the hood may become hot when used with the cooking appliance.
With regard to the technical and safety measures to be adopted for fume
discharging, it is important to closely follow the regulations provided by the
local authorities.
The hood must be regularly cleaned both on the inside and outside (AT LEAST
ONCE A MONTH).
This must be completed in accordance with the maintenance instructions provided in this manual. Failure to follow the instructions provided in this user guide regarding the cleaning of the hood and filters will lead to the risk of fires.
Do not use or leave the hood without the lamp correctly mounted due to the possible risk of electric shocks. We will not accept any responsibility for any faults, damage or fires caused to the appliance as a result of the non–observance of the instructions included in this manual.
This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste. Instead, it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal.
For further detailed information regarding the process, collection and recycling of this product, please contact the appropriate department of your local authorities or the local department for household waste or the shop where you purchased this product.
The manufacturer hereby declares that the appliance fulfills the requirements of the following
European Directives:
- Low Voltage Directive 2006/95/EC
- Electromagnetic Compatibility Directive 2004/108/EC
- This device is marked with a mark and the appropriate declaration of conformity is available to the market supervising authorities.
DIMENSIONS
INSTALLATION INSTRUCTIONS
Installation
The minimum distance between the supporting surface for the cooking equipment on the hob and the lowest part of the range hood must not be less than 50cm from electric cookers and 65cm from gas or mixed cookers. If the instructions for installation for the gas hob specify a greater distance, this must be adhered to
Electrical Connection
The main power supply must correspond to the rating indicated on the plate located inside the hood. If provided with a plug connect the hood to a socket that is in compliance with current regulations and located in an easily accessible area. If it is not fitted with a plug (direct mains connection) or if after installation the plug is not located in an accessible area, apply a double pole switch in accordance with standards which assures the complete disconnection of the mains under conditions relating to over-current category III, in accordance with installation instructions.
Warning! Before re-connecting the hood circuit to the mains supply and checking the efficient function, always check the mains cable is correctly assembled.
The hood is provided with a special power cable; if the cable is damaged, request a new one from Technical Service.
Mounting
Expansion wall plugs are provided to secure the hood to most types of walls/ceilings. However, a qualified technician must verify the suitability of the materials in accordance with the type of wall/ceiling. The wall/ceiling must be strong enough to take the weight of the hood. Do not tile, grout or silicone this appliance to the wall. Surface mounting only.
Use
This appliance is designed to be used either for exhausting or filter
versions. The models with no suction motor only operate in ducting mode and
must be connected to an external suction device (not supplied).
The connecting instructions are supplied with the peripheral suction unit.
In this case, the fumes are conveyed outside of the building by means of a
special pipe connected with the connection ring located on top of the hood.
Attention! The exhausting pipe is not supplied and must be purchased
separately.
The diameter of the exhausting pipe must be equal to that of the connection
ring. In the horizontal runs the exhausting pipe must be slightly slanted
(about 10°) and directed upwards to vent the air easily from the room to the
outside. Attention! If the hood is supplied with an active charcoal filter,
then it must be removed.
Connect the hood and discharge holes on the walls with a diameter equivalent
to the air outlet (connection flange).
Using the tubes and discharge holes on walls with smaller dimensions will cause a diminution of the suction performance and a drastic increase in noise.
Any responsibility in the matter is therefore declined.
- Use a duct of the minimum indispensible length.
- Use a duct with as few elbows as possible (maximum elbow angle: 90°).
- Avoid drastic changes in the duct cross-section.
- Use a duct with an as smooth as possible inside.
- The duct must be made of certified material.
Filter version
In this work mode the hood extracts and cleans the air from the kitchen and after that the air is sent back to the room. In order for the device to work properly an additional filter (or filters) must be installed. The filter utilizes active charcoal for air purification and can be obtained from your nearest retailer. The filter removes the grease and smells from the extracted air before sending it back into the room through the upper outlet grid.
Operation
The cooker hood is operated by using the Touch control panel.
Softtouch
Important! The Softtouch buttons in models Nova Trend have a vertical orientation. The above-described functions however remain the same.
- Speed decrease / switching off
- This button is used to decrease the speed of the motor. Press and hold this button to switch off the appliance
- Speed increase / switching on
- In the off – mode press this button to switch on the motor in speed one.
- Pressing this button while the appliance is in operation will increase the speed one step higher (up to speed 4. Note: the hood after 5 five minutes on the 4th gear will reduce speed to gear 3).
- The speed of the motor is shown on the LED display. The digit on the display corresponds to the speed of the motor (i.e. “1” indicates first speed, “2” indicates second speed etc.)
- LED display
- Indicates the current function/mode of the hood
- Timer
- Enables to set automatic switch off of the hood
- Lights on/of
Lights temperature adjustment
Please hold the “–” and “L” keys at the same time to open adjustment mode.. In this mode, the “L” sign starts flashing on the display. The adjustment takes place from 0 to 100%, with: 0 – maximum cool color, 50 – neutral, 100 – maximum warm. A single press of the “+” or “–” key shifts the color to one side by 10%, and holding the key down enables smooth adjustment. The settings are confirmed by pressing the “L” key or after 20 seconds without taking any action (timeout). The setting is saved in the flash memory and loaded after a power reset.
Speed Timing
Timer: to enable programming automatic switch off at any given time between 10 and 90 minutes, with 10-minute increments.
- To enable the programming function, turn the engine on using the “+” button to the level you want, and then press the button to program the switch-off time. The display will show a blinking 0, which means, that the time programming model entered.
- Select the automatic switch-off time using the “+” button, keeping in mind, that the number on the display, multiplied by the 10-minute interval, means the time of automatic switch-off (e.g. 1=10 min, 2=20 min, 3=30min, etc.)
- With the auto switch-off timer set, confirm the setting using the timer button, the display will stop blinking and will show the previously selected speed, and the blinking dot next to the speed will show the switch-off time. You can cancel the automatic switch-off function by pressing the timer button again while the time is counted down.
- Caution: Timer programming should be completed within 20 seconds, otherwise no action will be taken, and the hood will resume operation in normal mode.
Maintenance
ATTENTION! Before performing any maintenance operation, disconnect the hood from the electrical supply by switching off at the connector and removing the connector fuse. Alternatively, if the appliance has been connected through a plug and socket, then the plug must be removed from the socket
Cleaning
The cooker hood should be cleaned regularly (at least with the same frequency with which you carry out maintenance of the fat filters) internally and externally. Clean using the cloth dampened with neutral liquid detergent. Do not use abrasive products.
DO NOT USE ALCOHOL!
WARNING : Failure to carry out the basic cleaning recommendations of the
cooker hood and replacement of the filters may cause fire risks.
Therefore, we recommend observing these instructions.
The manufacturer declines all responsibility for any damage to the motor or
any fire damage linked to inappropriate maintenance or failure to observe the
above safety recommendations.
Grease filter
Traps cooking grease particles.
This must be cleaned once a month (or when the filter saturation indication system – if this option is available in the model you own – indicates this necessity) using non-aggressive d- e targets, either by hand or in the dishwasher, which must be set to a low temperature and a short cycle. When washed in a dishwasher, the grease filter may discolor slightly, but this does not affect its filtering ability.
To remove the grease filter, pull the spring release handle
Replacing lamps
Determine if your product is equipped with LED or halogen lights. The easiest way to do it is to check the attached energy label. If the lighting efficiency class is “B” or better the appliance has LED bulbs. In all other cases, it is equipped with halogen lights.
Refer to the drawing on page 21, as shown on the drawing 22. Disassemble the aluminium filters (as shown on the drawings 18, 19) then using your hand push the lighting downwards. Using your other hand grab the lighting from the outside. Disconnect the complete element and replace it with a new part. Proceed in reverse order to install the lighting.
IMPORTANT!! Always use the lighting of the same type as installed by the manufacturer. If you are not sure which part Grease filter to use contact your nearest Cylinda dealer.
Technical drawings
- Nova Trend SF40RFA E 90 045 04
- Nova Trend SF40SVA E 90 045 05
Service
- Nationwide service in Sweden
- Visit: www.cylinda.se
- Call: 0771-25 25 00
Declare
- Model code
- Serial number
- Purchase date
- Problem description
- Name and address
- Phone number
Contact us
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>