Siretta Tango 11A RF and Wireless Installation Guide
- June 1, 2024
- Siretta
Table of Contents
Siretta Tango 11A RF and Wireless
Product Information
- Specifications
- Product Name: Tango 11A
- Manufacturer: Siretta Ltd
- Recommended Mounting Surface: Conductive metal panel extending at least 12.5 cm in all directions
- Tools Required: Drill, 18mm drill bit, 19mm spanner or adjustable wrench, deburring tool, masking tape, pencil or marker
Product Usage Instructions
- Choosing Mounting Surface
- Surface Selection: The Tango 11A is ground plane independent but for optimal performance, mount it on a conductive metal panel extending at least 12.5 cm in all directions.
- When installing on a vehicle roof panel, choose a flat surface in a central position. Keep the antenna away from other roof-mounted items to avoid interference.
- Preparation
- Preparing the Surface: Mask the mounting area, drill cautiously to avoid damage, deburr the hole area, clean meticulously, strip paint and primer from the under-panel surface, and apply petroleum jelly or paint to prevent rust/corrosion.
- Installation
- Feeding the Cable: Carefully feed the cable through the prepared hole.
- Mounting the Antenna: Position the threaded part through the hole, protruding adequately from the other side.
- Securing the Antenna: Slide the washer onto the threaded section, twist the nut by hand, then secure it with a spanner. Check tightness without overtightening. Give a gentle tug to ensure firm anchoring.
- Post-Installation
- Inspection: Confirm antenna positioning is unobstructed and secure after installation.
- Maintenance: Periodically check for wear or loosening. Address issues promptly for optimal performance.
- Disclaimers and Waivers
- Safety Disclaimer: Follow local safety regulations for installation to prevent damage or injuries. The manufacturer is not liable for improper use.
- Professional Recommendation: For best performance and safety, consider professional installation to avoid warranty voidance and performance/safety issues.
FAQs
- Q: Can I install the Tango 11A on a non-metal surface?
- A: While it’s ground plane independent, for optimal performance, it’s recommended to mount it on a conductive metal panel extending at least 12.5 cm in all directions.
Materials Supplied
- 1x silicone rubber inner seal
- 1x flat washer
- 1x M17 nut
Required Tools:
- Drill, 18mm drill bit, 19mm spanner or adjustable wrench, deburring tool, masking tape, pencil or marker
Choosing mounting surface
- Surface Selection:
- The Tango 11A is ground plane independent, however, for optimal performance, it is recommended to mount the antenna on a conductive metal panel that extends at least 12.5 cm in all directions.
- When installing a vehicle roof panel, it’s important to choose a flat surface. Aim for a central position.
- Keep the antenna as far from other roof-mounted items such as the air conditioning unit, light bars, etc., to avoid interference.
Preparation
- Preparing the Surface: Mask the chosen mounting area to safeguard the surface.
- Start with a pilot hole at the desired location. Gradually enlarge the hole size until it is Ø18 mm in diameter.
- Be cautious while drilling, especially in a vehicle, to avoid damaging any underlying structures, like the headliner.
- After drilling, deburr and clean the area around the hole meticulously, ensuring all waste is removed.
- Strip the paint and primer from the under-panel surface. This step ensures proper contact for grounding with the washer and nut. To prevent rust or corrosion, apply petroleum jelly or paint around the cut edge of the hole.
Installation
- Feeding the Cable: Carefully feed the cable of the
- Tango 11A through the hole you prepared
- Mounting the Antenna: Position the threaded part of the antenna through the hole, ensuring it protrudes adequately from the other side.
- Securing the Antenna: On the underside of the mounting surface (or inside the vehicle if mounted on a roof), slide the washer onto the protruding threaded section.
- Next, twist the nut onto the thread by hand. Once it’s threaded correctly, use a spanner or appropriate tool to secure it in place. Make sure it’s secure but avoid overtightening, which could damage the antenna or mounting surface.
- After securing the antenna, give it a gentle tug to ensure that it’s firmly anchored.
Post-Installation:
- Inspection: After installation, inspect the antenna’s positioning to confirm that it’s not obstructed by any surrounding features and that it’s secure.
- Maintenance: Periodically check the antenna for any signs of wear or loosening. If you notice any issues, address them immediately to maintain optimal performance.
Disclaimers and Waivers
- Safety Disclaimer: The installation of this antenna should be carried out under local safety regulations. The manufacturer is not responsible for damages or injuries resulting from improper installation or use.
- Professional Recommendation: For optimal performance and safety, we recommend installation by a qualified professional. Improper installation may void the warranty and could lead to poor performance or safety hazards.
- Compliance Statement: Ensure compliance with all local building codes and electrical safety standards. The manufacturer is not liable for any violations of such regulations.
- General/Ongoing Maintenance: Regular maintenance checks are essential for sustained performance and safety. Failure to conduct these checks could result in unexpected performance issues and safety risks.
- Installation Confirmation: Upon installation, it is the responsibility of the installer to ensure that the antenna is securely mounted and functioning as intended. The manufacturer is not liable for issues arising from installation errors or oversights.
CONTACT
- Registered in England No. 08405712
- VAT Registration No. GB163 04 0349
- Siretta Ltd Basingstoke Road Spencers Wood Reading Berkshire RG7 1PW
- sales: +44(0)118 976 9000
- email: sales@siretta.com.
- web: www.siretta.com.
- Rev 1.0
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>