Siretta QUARTZ-ONYX 5G NR Gigabit Ethernet Industrial Router Range User Manual

June 4, 2024
Siretta

QUARTZ-ONYX
5G NR Industrial Router

Quick Start Guide
Rev 1.0

What’s in the Box?

This quick start guide is intended for the QUARTZ-ONYX router

Siretta QUARTZ-ONYX 5G NR Gigabit Ethernet Industrial Router Range - Fig
1

Common Accessories
If you ordered a router with accessories, you will also receive the following items:

Siretta QUARTZ-ONYX 5G NR Gigabit Ethernet Industrial Router Range - Fig
2

Siretta QUARTZ-ONYX 5G NR Gigabit Ethernet Industrial Router Range - Fig
3

NOTE – Both the DIN Rail Adapter and Wall Mount Bracket are supplied with x2 screws.

Optional Accessories

If you ordered a QUARTZ-ONYZ with accessories and opted for GPS, then you will also receive a GPS antenna.

Additional Items

You will require the following items for configuring your router:
» SIM that is subscribed to a 5G service with APN details
» Screwdriver to open the SIM cover
» PC to configure the router

Step 1: SIM: Use a screwdriver to open the SIM cover on your router.

Step 2: SIM: Insert a SIM card fully into the SIM slot. Close the SIM cover, ensuring it is screwed back into place. (SIM slot 1 is in use illustrated below)

Siretta QUARTZ-ONYX 5G NR Gigabit Ethernet Industrial Router Range - Fig
6

Step 3: ANTENNA CONNECTIONS: Screw in the 4 magnetic cellular antenna extensions onto the router. Twist the connector clockwise until the extension is firmly connected. Repeat the process for the 2 WiFi antennas onto the router (the cellular antennas must be attached to the magnetic antenna extension).

Siretta QUARTZ-ONYX 5G NR Gigabit Ethernet Industrial Router Range - Fig
7

If you have a GPS router, connect the GPS antenna to the GPS connector on the router.

Siretta QUARTZ-ONYX 5G NR Gigabit Ethernet Industrial Router Range - Fig
8

Step 4: LAN CONNECTION: Connect one end of the Ethernet cable to the router LAN port, and connect the other end of the cable to an Ethernet port on your PC.

Step 5: POWER : Plug in the green power connector on the power adapter cable into the router as shown below.

Step 6: POWER: Select the connector type for your power adaptor depending on your geographical location (UK/EU/USA/AU). Plug the power adaptor to the mains.

Siretta QUARTZ-ONYX 5G NR Gigabit Ethernet Industrial Router Range - Fig
11

Step 7: POWER: Switch on the power. See the table below for LED indications when the router is powered on.
Table 1. Router LED indication

LED color State
PWR Green when ON If this LED is OFF, ensure the power adaptor is connected

correctly and the mains power is switched on.
WLAN Green when ON|  Router WiFi is enabled. If this LED is OFF, WiFi is not enabled or supported.
ERR Red when ON| The router is not registered to the network. Check the SIM card is inserted correctly.
Signal Strength Green when ON| If only one LED is on, check the antenna position or try a different location.

Step 8: IP ADDRESS: Obtain the IP address of your router. You can find this on the silver label on the back of your router. Type the IP address of your router into your PC browser. When prompted for your username and password use the following:
User name: admin
Password: admin
These credentials are factory defaults. You can set your own username and password in the router settings.

Siretta QUARTZ-ONYX 5G NR Gigabit Ethernet Industrial Router Range - Fig
12

Step 9: APN SET-UP: On successful login, navigate to the Basic Network > Cellular tab.
When you arrive at the ‘Cellular Settings’ page, you will need to enter the APN details for the network provider of your SIM card.
In the image below, we have used the APN details relevant for “EE”. These being:

• APN: everywhere
• Username: secure
• Password: secure|
---|---

You are not required to enter any ‘Proxy’ or ‘Port’ details.

Siretta QUARTZ-ONYX 5G NR Gigabit Ethernet Industrial Router Range - Fig
14

Step 10: CONNECTING TO NETWORK: Click “Save”. Your router will reboot itself. The router will then connect to the network and is ready for use with your application.

Siretta QUARTZ-ONYX 5G NR Gigabit Ethernet Industrial Router Range - Fig
15

NOTE – If you cannot access the router GUI, please check your local area network settings.

Further Information

For more information when using your router, a range of application notes, hardware, and software user manuals are available to download. You can request these from your
Siretta representative, alternatively these can be downloaded from www.siretta.com

sales +44 (0)118 976 9000
email sales@siretta.com
www.siretta.com
Siretta Ltd
Basingstoke Road Spencers Wood
Reading Berkshire RG7 1PW
United Kingdom
Company No. 08405712
VAT Registration No. GB163 04 0349

https://www.siretta.com/

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals