VARDAFLEX Sauna SVQ 2700K LED Strip User Manual
- June 1, 2024
- VARDAFLEX
Table of Contents
VARDAFLEX Sauna SVQ 2700K LED Strip
Specifications:
- Power Supply: 6W, 0.25A
- Number of LEDs per meter : 108
- LED Spacing: 9.26mm
- Maximum Length per Connection: 10 meters
- Dimensions (L x W x H): 55.56 x 16 x 17 mm
- Minimum Bending Diameter: 300mm
- Operating Temperature: IP68
Product Usage Instructions
Important Installation Guidelines:
- Before installation, switch off the power supply. Ensure that the power cannot be accidentally turned back on.
- Never operate LED strips in a rolled-up state.
- Cutting the strips must be done precisely along the provided separation lines.
- Ensure appropriate wire cross-section for installation.
Mounting LED Strip:
Instructions for mounting the LED strip go here…
Water Stop:
If used underwater, the water stop must be installed above the waterline and should not be submerged.
Dimensions:
Details about dimensions for different applications (e.g., single color, CCT, RGB, RGBW) are provided here.
Installation in Aluminum Profile:
Instructions for installation in an aluminum profile with details on angle and side offsets.
FAQ:
- Q: Can the LED strips be cut to a custom length?
- A : Yes, the LED strips can be cut precisely along the designated separation lines to achieve a custom length.
- Q: What is the recommended operating temperature range for the LED strip?
- A : The LED strip is designed to operate within an IP68-rated temperature range for optimal performance and longevity.
TECHNICAL DATA
power supply | 24 V power supply with constant voltage output |
---|---|
power/m | 6 W |
current strength/m | 0.25 A |
quantity LED/m | 108 |
LED spacing | 9.26 mm |
dimension of segments | 55.56 mm, 6 LEDs |
length | maximum length per connection 10 meters |
dimensions | 55.56* x 16 x 17 mm |
bending diameter | min. 300 mm |
temperature range | -45 to +90° C |
processing temperature | +10 to +90° C |
Section length | module
NOTICE:
The light colour 2700 K contains a light source of energy efficiency class E.
INSTALLATION NOTE
The outer jacket of the product has an expansion factor of 0.05%, e.g. operating length of 10.000 mm ≙ an expansion factor of ± 5 mm.
IMPORTANT INSTALLATION INSTRUCTIONS:
- Be sure to have a professional electrician complete the installation. There is no warranty coverage for any lights installed without observing European safety directives.
- Switch off the voltage prior to installation. Ensure that the voltage cannot be accidentally switched on again.
- VARDAFLEX LED strips is suitable for direct mounting on normal flammable immovable surfaces, e.g. on wood and wood-based materials with more than 2 mm thickness.
- Before turning the power on, check all connections for correctness and short-circuit.
- Never operate the LED strips when rolled up.
- Cut the strips exactly at the specified severing lines.
- Please make sure that an appropriate flex cross-section for the connection between the LED strip and the controller is used.
- Do not exceed the operating temperature of +90° C.
- Please do not carry out any repairs yourself. Failure to comply may lead to voiding of the manufacturer‘s guarantee.
HANDLING
MOUNTING LED-STRIP:
CAUTION!
Do not install VARDAflex LED strips in a suspended way!
ANTI-WICKING FERRULE:
- The removal of anti-wicking ferrule will increase the risk of water ingression an void the warranty out of it.
- For Underwater application, do not immerse anti-wicking ferrule in the water.
DIMENSION
INSTALLATION
INSTALLATION IN THE ALUMINIUM PROFILE:
PROFILE TRANSITIONS:
DISTANCE FOR INSTALATION OF INJECTION-MOULDED INFEEDER:
Keep 10~20 mm distance from the injection-molded infeeder SL/SR as well as the end cap to the edge of the aluminum profile.
Keep 10~20 mm distance from the injection-molded in feeder ST as well as the end cap to the edge of the aluminum profile.
It is forbidden to force the injection-molded end to fit into the mounting profile and make light deformation.
Mechanical stress on front connector cable shall be avoided.
Install the light in one direction, no matter what kind of connector used. Don’t let it choke in the middle.
BENDING IN THE PROCESS OF INSTALLATION:
The installing angle should be less than 15 degrees when pressing the light to the aluminum profile by hand.
The circuit board could be damaged if installing angle larger than 15 degree.
MARKS AND SYMBOLS:
DISPOSAL:
Dispose of electrical and electronic equipment in an environmentally sound manner. For more information, contact your local authority.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>