VARDAFLEX RU-86548 3inONE-30 LED Strip Light Instruction Manual

June 3, 2024
VARDAFLEX

LOGO

VARDAFLEX RU-86548 3inONE-30 LED Strip Light

VARDAFLEX RU-86548 3inONE-30 LED Strip Light PRODUCT-
IMG

The LED strip LED board is suitable for outdoor and indoor installa tion in dry and wet rooms.

Risk of electric shock!

Be sure to have a professional electrician complete in stallation. There is no warranty coverage for any lights installed without observing european safety directives.

Caution!

  • Only connect the LED strip to a suitable power supply (24 V DC).
  • Only operate when completely unrolled.
  • Connect LED strips in parallel

Scope of delivery

  • 1 x 5 metre LED strip
  • 20 x fixing brackets
  • 2 x silicone cap closed
  • 2 x silicone cap with cable feed-through
  • 1 x socket with 150 mm connection cable
  • 1 x plug-endcap

Technical data

  1. Power supply  24 V power supply with constant output voltage
  2. Power  36 W
  3. Current strength  1.5 A
  4. Beam angle  120°
  5. Quantity LED  150
  6. Length  maximum 5 metres per connection
  7. Dimensions  5000 x 12 x 4 mm
  8. Bending diameter  100 mm
  9. CE Compliant with the applicable european CE directives
  10. Safety class 3 – low voltage protection
  11. UV not UV resistant

Installation

Risk of electric shock!

Switch off voltage prior to installation. Ensure that voltage cannot be accidentally switched on again.

Caution!

On conducting surfaces, place an insulation layer between the LED strip and surface. Surfaces must be flat, free of dust, grease and dry.

  1. Prepare surface.
  2. Shorten LED strip if necessary (Fig. 1).
  3. Mount LED strip with help of included holders indistance of ~25-30 cm without pressing onto electronic components.
  4. Connect LED strip to power supply.

Shortening the LED strip

Risk of electric shock! Always disconnect the mains plug before shorteningVARDAFLEX RU-86548 3inONE-30 LED Strip Light FIG
\(1\)

Separate the LED strip at the marked position. For a tightly assembled LED strip is a micro side cutter or an optional cutter required.
Glue the end cap with neutral cross-linking silicone at the end of the separation point

Caution!

With soldered connections note that the soldering tem perature is 260° C and the soldering duration a maximum of 10 seconds per soldering point.
Only use neutral cross-linked silicon (never use silicon which includes vinegar!).

Connection

  1. Use the enclosed socket with 150 mm connecting cable and plug it into the already soldered connector of the LED strip (Fig. 2).
  2. Close the end of the LED strip using the enclosed connector end cap by inserting it into the soldered socket at the end of the LED strip (Fig. 3).
  3. Optional : To make another connection after cutting the LED strip, use a 4-pole connection cable (fine-stranded), e.g. 89994, and pull the enclosed silicone cap with cable feed- through over the already stripped wires. Solder them with lead-free solder to the solder contacts of the the soldering contacts of the cutting point, observing the temperature specification mentioned above.
  4. Seal open silicone tube ends with neutrally crosslinking silicone (e.g. 88670) and the enclosed silicone caps.VARDAFLEX RU-86548 3inONE-30 LED Strip Light FIG \(2\)

Disposal
Dispose of electrical and electronic equipment in an environmentally friendly manner. Please contact your local council for further information.

Carl-Zeiss-Str. 15 28857 Syke
Please refer to the respective article on www.rutec.de for complete technical data!

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals