TC-NTL150-100W Enclosure Heating Instruction Manual
- June 1, 2024
- TRU
Table of Contents
TC-NTL150-100W Enclosure Heating
Intended use
These heaters are used in enclosures where damage from condensation must be
prevented, or where the temperature may not fall below a minimum value. The
aluminium profile heater body design has a chimney effect and distributes the
heat evenly. The heaters are designed for permanent operation. Pressure clamb
connectors save time and simplify installation. The product is intended for
indoor use only. Do not use it outdoors. Contact with moisture must be avoided
under all circumstances.
If you use the product for purposes other than those described, the product
may be damaged.
Improper use can result in short circuits, fires, electric shocks or other
hazards.
The product complies with the statutory national and European requirements.
For safety and approval purposes, you must not rebuild and/or modify the
product.
Read the operating instructions carefully and store them in a safe place. Make
this product available to third parties only together with the operating
instructions.
All company names and product names are trademarks of their respective owners.
All rights reserved.
Delivery content
- Product
- Operating instructions
Latest product information
Download the latest product information at www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.
Description of symbols
The following symbols are on the product/appliance or are used in the text:
The symbol warns of hazards that can lead to personal injury.
The symbol warns of dangerous voltage that can lead to personal injury by electric shock.
Safety instructions
Read the operating instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling in this manual, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/ guarantee.
Caution, safety hazard!
**The product should only be installed by people with relevant electrical knowledge and experience! ***
If it is not installed properly, you risk:
- your own life
- and the life of user of the electrical device.
- if it is not installed properly, you risk severe damage to property, e.g., by fire.
You face the risk of personal liability for personal injury and material damage.
Always consult an electrician!
Technical knowledge required to perform the installation:
For the installation, the following specialist knowledge is required in particular:
-
The “Five safety rules”: Disconnect from the mains; protect against accidental switch-on;
ensure there is no voltage; earth and short-circuit; cover or protect neigh bouring live parts. -
Use suitable tools, measuring devices and personal protective equipment, where necessary.
-
Analyse measurement results.
-
Use electrical installation materials to ensure the turn-off criteria.
-
IP protection ratings
-
Install electrical installation materials
-
Type of power supply (TN system, IT system, TT system) and the corresponding connection criteria (classic earthing, protective earthing, necessary additional measures etc.)
If you are not a professional, do not do it yourself, have it performed by a specialist.
General information
- The device is not a toy. Keep it out of the reach of children and pets.
- Do not leave packaging material lying around carelessly. This may become dangerous playing material for children.
- If you have questions which remain unanswered by these operating instructions, contact our technical support service or other technical personnel.
- Maintenance, modifications and repairs must only be completed by a technician or an authorised repair centre.
Handling
Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
Operating environment
- Do not place the product under any mechanical stress.
- Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam and solvents.
- Protect the product from high humidity and moisture.
- Protect the product from direct sunlight.
- Do not switch the product on after it has been taken from a cold to a warm environment.
The condensation that forms might destroy the product. Allow the product to reach room temperature before you use it.
Operation
- Consult an expert when in doubt about the operation, safety or connection of the appliance.
- If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. DO NOT attempt to repair the product yourself. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
Mains cable
Do not modify or repair mains supply components including mains plugs, mains cables, and power supplies. Do not use damaged components. Risk of death by electric shock!
- Make sure that the mains cable is not squeezed, bent, damaged by sharp edges or put under mechanical stress.
- Avoid excessive thermal stress on the mains cable from extreme heat or cold.
- Do not modify the mains cable. Otherwise the mains cable may be damaged. A damaged mains cable can cause a deadly electric shock.
- Do not touch the mains cable if it is damaged.
- Never use the product if the mains cable is damaged.
- Ensure that cables are not pinched, kinked or damaged by sharp edges.
- Always lay cables so that nobody can trip over or become entangled in them. This poses a risk of injury.
Connected devices
- Also observe the safety and operating instructions of any other devices which are connected to the product.
Product overview
-
Item No. 2898213
-
Item No. 2898215
-
Item No. 2898216
The technical specification on the type of product must be observed !
Attention: Hot surface when in use! Risk of injury!
The installation must only be performed by qualified, trained personnel. The
applicable, Country-specific regulation regarding power supply are to be
observed during installation.
The safety and protection against incidental contact is to be ensured through
proper installation.
Installation
The product should only be installed by people with relevant electrical
knowledge and experience!
If it is not installed properly, you risk your own life, you risk severe
damage to property, e.g. by fire.
You face the risk of personal liability for personal injury and material
damage.
Always consult an electrician!
For safety reasons and to ensure unobstructed air circulation, ther must be at
least 100 mm of space between the heater and components.
In the blow direction of hot-air fans there must be at least 100 mm of space
between the heater and components.
For better heat distribution the heaters are to be installed vertically in the lower part of the electric cabinet. Air outlet at the top. The heaters must NOT be mounted on flammable materials (wood, plastic etc.)
- Loose the screw of the cover
- Connect the cables to terminal
- Then tight the screws
Applicable for : Item No. BN 2898213 / Item No. BN 2898215
Applicable for: Item No. BN 2898216
Connection: 3 presure clamps for standard wire 0.5-1.5 mm² (with wire end ferrule) and rigid wire 0.5-2.5 mm²
Safety Notice: In order to keep safety for operations, please ask an electrician to install the cabling. All products with aluminum body need to connect with Earth wire for safety. If you are not a professional, do not do it yourself, have it performed by a specialist.
Operation
The heaters must only be operated with fans. Heaters which are equipped with
axial fans by the user, must be mounted with the mounting kit included in the
package.
The on/off indicator consists of an LED light (BN 2898213) that is visible as
long as the product is functional.
Troubleshooting
| Problem | Possible cause | Suggested solution |
|---|---|---|
| The heater dose not turn on | Improper electric contact | Check again the |
connections
Cleaning and care
Important:
-
Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions.
They damage the housing and can cause the product to malfunction. -
Do not immerse the product in water.
- Disconnect the product from the power supply.
- Clean the product with a dry, fibre-free cloth.
- Use low pressure compressed air to blow out the dust deposits from the interior
Disposal
This symbol must appear on any electrical and electronic equipment placed on
the EU market. This symbol indicates that this device should not be disposed
of as unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose
of it separately from unsorted municipal waste. Spent batteries and
accumulators, which are not enclosed by the WEEE, as well as lamps that can be
removed from the WEEE in a non-destructive manner, must be removed by end
users from the WEEE in a non-destructive manner before it is handed over to a
collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free take-back of waste. Conrad provides the following return options free of charge (more details on our website):
- in our Conrad offices
- at the Conrad collection points
- at the collection points of public waste management authorities or the collection points set up by manufacturers or distributors within the meaning of the ElektroG End users are responsible for deleting personal data from the WEEE to be disposed of.
Technical data
Power supply
Input voltage/current………………… 120-250V AC/DC
……………………………………………… Item No. BN 2898213 / BN 2898215
Input voltage/current………………… 120-250V AC/DC
……………………………………………… Item No. BN 2898216
Power consumption…………………. 15 W to 100 W
Protection class ………………………. IP20
Environment
Operating temperature …………….. -45 to +70 °C
Operating humidity ………………….. max. 90 % RH (non-condensing)
Storage temperature………………… -45 to 70 °C
Storage humidity……………………… max. 90 % RH (non-condensing)
Other
| Dimensions| Weight
---|---|---
BN 2898213| 175 (L) x 58 (H) x 70 (D) mm| 396 g
BN 2898215| 176 (L) x 64 (H) x 61 (D) mm| 380 g
BN 2898216| 150 (L) x 90 (H) x 60 (D) mm| 462 g
Customer Support
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represents the technical status at the time of printing.
Copyright 2024 by Conrad Electronic SE.
*2898213_15_16_V4_0224_02_m_VTP_EN
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>