TRU LEA Professional Smart Amplifiers Installation Guide

June 4, 2024
TRU

Install Guide
LEA Connect

LEA NETWORK SET UP

  1. Power on the unit. The LEA logo on the front of the amp will turn from green to blue.

  2. Wait 30 seconds then press the WiFi button by the ethernet port.TRU LEA Professional Smart Amplifiers -

  3. Within 30 seconds, the WiFi name and IP should be visible on the front screen.TRU LEA Professional Smart Amplifiers - front screen

  4. On a WiFi-enabled device, search the available WiFi connections for the “AP Name.” Select the WiFi address and connect to it on your device.TRU LEA Professional Smart Amplifiers - available WiFi

  5. Once connected to your device, open a web browser and input the IP address from the front of the display to the URL barTRU LEA Professional Smart Amplifiers - display

  6. You should see the device. Tap the WiFi symbol.

  7. Enable WiFi.

  8. Input the SSID (case sensitive), and the WiFi password.TRU LEA Professional Smart Amplifiers - WiFi password

  9. Press the WiFi button on the back of the LEA amp. The light should turn green.

  10. Tap Save.TRU LEA Professional Smart Amplifiers - should turn green

  11. The WiFi name and a new IP address will be displayed on the front of the amp if connected properly. If you do not see this, repeat steps 1-9.TRU LEA Professional Smart Amplifiers - will be displayed LEA NETWORK SET UP cont.

  12. Open a web browser and input the new IP address into the URL bar. The device page should now be visible (image1).
    a. Tap the device name to see the channels (image 1).
    b. Tap on the channel you want to attach the speakers to (image 2).
    c. Tap the button and select “Import” (image 3).
    d. Upload the custom TruAudio DSP for the applicable speakers or subwoofers. See the DSP chart for more information.

  13. Connect your device to the main WiFi.TRU LEA Professional Smart Amplifiers - DSP chart for more

  14. You are now ready to attach speakers to the amplifier.

  15. Repeat step 13 for the remaining zones.

Be sure to connect the correct speaker with the correct DSP to the correct channel of the amplifier.

OBTAINING TRUAUDIO CUSTOM DSPs

Visit www.soundvisiontech.com/resources/lea-amplifier- dsp/ or any LEA amplifier product page on www.soundvisiontech.com

Preset Name Speakers
AS Speaker For AS-2, AS-2, & AS-360 speakers (70v ONLY)
AS3 Speaker For AS-3 speakers (70v ONLY)
BDCL Speaker For BeatDrop and/or CL-70v speakers (70v ONLY)
HS Sub For HS-SUB-12 (70v ONLY)
P10 Sub For ST-10PRO (4Ω ONLY)
P12 Sub For ST-12PRO (70v ONLY)
ST10.2 Sub For ST-SUB-10.2 (4Ω ONLY)
ST-12.2 Sub For ST-SUB-12.2 (70v ONLY)

NOTE: If combining the AS-3 with AS-2 or AS-360, it’s recommended to use the AS3 Speakers DSP.
DO NOT use the AS-1 with this preset.
Choose the correct DSP based on the speakers you will install. If you need additional support, contact TruAudio technical support at 888-858-1555.

LEA SOURCE SET UP

  1. Attach the included RCA wires to the (2) phoenix connectors as shown in the illustration. Make sure to match the colored wires in the correct order.
  2. Connect the source to the RCA wires.

WIRING
ST-12PRO or HS-SUB12 in 70v
Powering the ST-12PRO or HS-SUB-12 in 70v (Standard Mode)
Connect the red wire (70v+) and the black wire (70v-) to the 70v amplifier.

TRU LEA Professional Smart Amplifiers - Standard
Mode\)

ST-10PRO
Powering the ST-10PRO in 4Ω
Connect the red wire (+) and the black wire (-) to the 4Ω amplifier

TRU LEA Professional Smart Amplifiers - Powering

Powering the ST-12PRO or HS-SUB12 in 4Ω
Connect the yellow wire (4Ω+ positive input) and the blue wire (4Ω – negative input) to the 4Ω amplifier.
SPECIAL NOTE: Make sure your subwoofer amplifier can handle a 4Ω load and has a maximum wattage output of no more than 200 watts.
TruAudio recommends running the st-12PRO and HS-SUB12 in 70v with an LEA amplifier using a custom DSP designed by TruAudio for maximum performance.

WIRING cont.
70V Tap Settings
Set taps to desired listening level. The tap settings can be changed as long as the total speaker wattage does NOT exceed 100% of the amp’s power.
NOTE: Lower tap settings allow for more speakers but a lower maximum volume.

Finding the Correct Tap Setting
Example:
AMP POWER = 700W
700W ÷ 64W (Tap setting) = 10 Speakers
OR
700W ÷ 50W (Tap setting) = 14 Speakers
OR
700W ÷ 30W (Tap setting) = 23 Speakers

TRU LEA Professional Smart Amplifiers - maximum volume

NOTE: If using 70V, the Acoustiscape speakers MUST be set to the proper TAP setting prior to connecting it to the amplifier. The speaker will blow if set to 8Ω and will not be covered by warranty. The higher the TAP setting the more power it will receive from the amplifier and the louder the speaker will go. The TAP settings give the listener greater flexibility for layout design. It also allows each speaker to be tapped at different levels creating an even sound stage.

LEA AMPLIFIER HIGHLIGHTS

MODEL # of Channels 70V / 100V Size
84 / MD 4 80W 80W 40W 80 W 111
88 / 88D 8 80W 80W 40W 80 W 111
164 / 164D 4 160 W 160 W 80 W 160 W 1U
168 / 168D 8 160 W 160 W 80 W 160 W 111
352 / 352D 2 350 W 350 W 175 W 350 W lu
354 / 354D 4 350 W 350 W 175 W 350 W 11L1
702 / 702D 2 700 W 700 W 350 W 700 W 111
704 / 704D 4 700 W 700 W 350 W 700 W 111
1504/1504D [COMING SOON) 4 1500 W 1500 W 1500 W 1500 W 2U
3004/3004D (COMING SOON) 4 3000 W 3000 W 3000 W 3000 W 2U

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals