Electrolux FPFU19F8WF Single Door Refrigerator Instruction Manual

Electrolux FPFU19F8WF Single Door Refrigerator

Product Specifications

• Model: TTFLTRICEKIT
• Compatible Models: FPFU19F8WF, FPRU19F8WF, EI33AF80WS, EI33AR80WS
• Kit Contents:
  • Instruction Sheet
  • 1x 218976831
  • 2x 240396804
  • 2x 240396805
  • 1/4 Green water line (16 feet)
  • 1/8 Wiring harness strain relief
  • A19408101 Wiring Harness (19 feet)
  • 2x 305346-00 Wiring Harness support clips
  • 1x 1/4 Union 5304518370

Product Usage Instructions

Access Cover Removal:

1. Remove the 8 access panel screws on the refrigerator and Freezer.
2. Apply the protective rubber trim (D) to the inside edge of the water valve opening on both access covers.

Refrigerator Connections:

1. Feed the green water line (A) and wiring harness (E) through the opening of the refrigerator access cover.
2. Push the green water line into the green port of the water valve.
3. Connect the wiring harness (E) to the connector on the refrigerator.
4. Locate wiring harness support clip at the top of the refrigerator machine compartment (F), and insert wiring harness to secure.

Freezer Connections:

1. Disconnect the 10 Gray water line from the water valve by pushing upward on the port tab, while pulling out the line. Install a union fitting on the end of the gray line.
2. Feed the green water line (A) coming from the refrigerator along with the wiring harness (E) through the opening of the access cover.
3. Push the green and grey water line into 1/4 union (G) to connect the two.
4. Connect the harness (E) from the refrigerator to the connector for the freezer. Locate the wiring harness support clip at the top of the refrigerator machine compartment (F), and insert  wiring harness to secure.

Water Line Final Connections:

1. Fasten the strain reliefs for the green water line (B) and for the wiring harness on each unit (C).
2. Attach the two adhesive support clips (F) and insert the green water line and harness.
3. Loop the water line and wire harness in the centre of the two units.

Frequently Asked Questions (FAQ):

• Q: Can I install this kit without professional help?
  A: It is recommended to have an authorized service technician install the filtered ice kit for proper installation and safety reasons.

• Q: What tools are required for installation?
  A: You will need a 1/4 nut driver for installation.

Models:

• FPFU19F8WF
• FPRU19F8WF
• EI33AF80WS
• EI33AR80WS

Kit Contents

ORIGINAL CONFIGURATION

INSTRUCTION SHEET

• NOTE: This kit is designed to provide filtered water to the freezer ice maker when a single-door freezer is installed next to a single-door refrigerator.
• NOTE: An authorized service technician is recommended to install the filtered ice kit
• NOTE: Disconnect electrical power prior to servicing this product.

Tools Required : 1/4” nut driver

Access Cover Removal

CAUTION : Wear gloves and use extreme CAUTION when installing the PROTECTIVE rubber trim. The opening may have sharp edges.

1. Remove the 8 access panel screws on the refrigerator and Freezer.
2. Apply the protective rubber trim (D) to the inside edge of water valve opening on both access covers.

Refrigerator Connections

1. Feed the green water line (A) and wiring harness (E) through the opening of the refrigerator access cover.
2. Push the green water line into the green port ofthe water valve.
3. Connect the wiring harness (E), to the connector on the refrigerator.
4. Locate the wiring harness support clip at the top of the refrigerator machine compartment (F), and insert the wiring harness to secure.

Freezer Connections

NOTE: The freezer water valve and the connecting harness are not used when this kit is installed for filtered water provided by the paired refrigerator.

1. Disconnect the 10″ Gray water line from the water valve by pushing upward on the port tab, while pulling out the line. Install union fitting on the end of the gray line.
2. Feed the green water line (A) coming from the refrigerator along with the wiring harness (E) through the opening of the access cover.
3. Push the green and gray water line into 1/4″ union (G) to connect the two.
4. Connect the harness (E) from the refrigerator to the connector for the freezer. Locate the wiring harness support clip at top of the refrigerator ma-chine compartment (F), and insert the wiring harness to secure.
5. Disconnect the harness connection from the water valve. Not required. Water will be supplied from the refrigerator water valve.
6. Reinstall access cover for both units.

Water Line Final Connections

1. Fasten the strain reliefs for the green water line (B) and for the wiring harness on each unit. (C)
2. Attach the two adhesive support clips (F) and insert the green water line and harness.
3. Loop the water line and wire harness in the centre of the two units.
4. Connect and turn on the water supply.
5. Purge air from water lines by dispensing water from the refrigerator water dispenser.
   (See Use and Care manual for details on water dispenser operation and purging method)

© 2016 Electrolux Home Products, Inc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>