LawMate PV-DY40UW DVR Wi-Fi Ultra HD 4K Module User Guide

LawMate PV-DY40UW DVR Wi-Fi Ultra HD 4K Module

Product Information

Specifications

• Model: PV-DY40UW / PV-DY40UWW
• Resolution: 4K Ultra HD
• Usage: Law Enforcement and Home Security
• Package Contents: DVR, RF Remote, Adapter, Memory Card, Extended Battery, USB Cable x2

Product Usage Instructions

Charge the Battery

Charge the DVR

1. Plug the Type-C USB end of the cable into the DVR and connect the other end to a USB power source or a power bank.
2. Alternatively, use the extended battery as a power source. Connect it to the device and charge it via USB cable. The green LED indicates charging, and it goes off when fully charged.

Charge the RF Remote

1. Power off the remote control and connect the Type-C USB end to it.
2. Connect the other end of the USB cable to a charger and plug it into an AC wall outlet. Check the LED indicators for charging status.

Format Memory Card

Press and hold the designated button to format the memory card.
Make sure to format it before initial use.

Operation (DVR only)

• Power On / Off: Slide switch upward to turn on and downward to power off.
• Recording: Device starts recording automatically 6 seconds after powering on.
• Vibration Switch: Toggle switch to turn vibration on or off.
• Wi-Fi: Switch to turn Wi-Fi on or off. Refer to the Wi-Fi quick guide for setup instructions.
• Reset: Press reset key if device functions abnormally.
• Factory Reset: Press and hold default key for 10 seconds to restore factory settings.

Frequently Asked Questions (FAQ)

• Q: What is the standby time of the RF Remote?
  A: The standby time of the remote control is approximately 18 hours. Always remember to turn it off after use.

• Q: How do I know if the battery is fully charged?
  A: For the DVR, the green LED indicates charging and goes off when fully charged. For the RF Remote, the green LED indicates charging and turns off when fully charged.

PV-DY40UW
PV-DY40UWW
4K Ultra HD DIY DVR Quick Guide

Names and Parts – DVR

1. Power On / Off Switch
2. Default Key
3. Camera Lens
4. Wi-Fi Antenna
5. RF Pairing Button
6. Wi-Fi On / Off Switch
7. Continuous Recording / Motion Detection Recording
8. Vibration Switch
9. Charging (green) LED
10. Wi-Fi (orange) LED
11. Pairing (blue) LED
12. Reset Key
13. Pairing (red) LED
14. Rec (red) LED
15. Power (blue) LED
16. Memory Card Slot
17. USB Port
18. Extended Battery

Names and Parts – RF Remote

1. USB Port (Charge)

2. DVR Power On LED (Blue)

3. DVR Power On / Off Button

4. DVR Rec LED (Red)

5. DVR Rec On / Off Button

6. DVR Wi-Fi LED (Orange)

7. DVR Wi-Fi On / Off Button

8. Remote Power On (down) / Off (up)

9. Remote Vibration On
   (down) / Off (up)

10. Remote charge LED
    (Green) / Remote Command sent LED (Blue)

Package Content

Charge the Battery

Charge the DVR

1. Plug the Type-C USB end of the cable to 17  and connect the other end to an USB power source (as shown above), or plug it to a power bank of your own choice.

2. You can also use the extended battery as power source. Connect the extended battery with the device and charge the battery with USB cable via USB power source.
   Once the battery is fully charged, you can remove the USB cable and adopt the battery as the power source.

   • Solid green LED – charging.
   • Green LED goes off – fully charged.

Charge the RF Remote

1. Power off the remote control by sliding 8  upwards.
   It is important to turn off the remote control while charging and make sure it is fully charged everytime before use.

2. Connect the T ype-C USB end to 1  on the  remote control.

3. Connect the other end of the USB cable to a USB charger, and connect the charger to an AC wall outlet.
   Check 10  for battery / charging status

   • Solid green – Charging
   • Green LED turns off – Fully charged
   • Blue LED blinking – Battery low
     The standby time of the remote control is approximately 18 hours. Please always remember to turn it off after use.

Format Memory Card
2Press and hold , and turn on the device. Release when the red LED blinks. After the format is done, device will automatically turn off.
※ It is important to format the card when using it for the first time.

Operation (DVR only)

1. Power On / Off
   Switch 1 upward to turn on; downward to power off.

2. Recording
   6 seconds after device is on, it will start to record automatically.

3. Vibration
   Switch 8 upward to turn on, or downward to turn off.

4. Wi-Fi
   With device powered on, switch 6  upward to turn on,  or downward to turn off.
   For more information about Wi-Fi connection set up, please refer to Wi-Fi quick guide.

5. Reset
   When the device functions abnormally, press 12  once.

6. Restore to all factory settings:
   With device powered on, press and hold 2  for 10  seconds, and release. Red and orange LED will flash 3 times, indicates that the unit is restored to factory setting.

• Warranty will be void if serial number sticker is tampered.

Pair up with the RF Remote

1. Power on the DVR and then long pr 5ess on DVR, and release the button until you see the blinking blue & red LED, which indicates that the DVR is waiting to be paired up.
2. Power on the remote control and enable the vibration alert. Press Rec button on the remote control, with the remote vibrates twice and the blinking blue & red LED go off, the remote is successfully paired up with the DVR.

Operation on RF Remote

For Remote Control:

1. Power On / Off
   Slide “Pwr” switch downward to power on; upward to power off.

2. Vibration
   Slide “Vib” switch downward to turn on; upward to turn off.

For DVR

1. DVR Turn On / Off
   Long press 3 on the remote at least 3 seconds to power on / off the DVR.

2. Recording
   Press 5 on the remote once to start or stop the recording.

3. Wi-Fi
   Press 7  on the remote once to enable or disable Wi-Fi.

LED Indicators

Vibration Alert

• Rec On – 1 long vibration
• Snap Shot – 1 short vibration
• Wi-Fi On – 2 short vibrations
• Wi-Fi Off – 2 short vibrations
• Power Off – 1 short vibration

Date and Time Setting
Please refer to the Synchronize the Time steps on the PV Cam Viewer guide.

Download Files

1. Use a memory card reader to transfer files from the memory card to the computer.
2. Connect the device to the computer with memory card inserted. Turn on the device and it will work as a flash drive.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>