SEALEY VS7020.V3 Wheel Bearing Removal Kit Instruction Manual
- June 1, 2024
- SEALEY
Table of Contents
Instruction Manual
VS7020.V3 Wheel Bearing Removal Kit
WHEEL BEARING REMOVAL/INSTALLATION KIT
MODEL NO: VS7020.V3
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions,and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
|
---|---
Refer to instruction manual| Wear eye protection
SAFETY
WARNING! Ensure all Health and Safety, local authority, and general
workshop practice regulations are strictly adhered to when using tools.
DO NOT use tools if damaged or worn.
Maintain the tools in good and clean condition for best and safest
performance.
Ensure all threads are clean and well lubricated.
Ensure vehicle is adequately supported with axle stands, ramps, etc. as
appropriate.
Wear suitable clothing to avoid snagging. DO NOT wear jewellery. Tie back long
hair.
Wear approved eye protection. A full range of personal safety equipment is
available from your Sealey stockist.
Account for all tools and parts being used and DO NOT leave them in or on the
vehicle.
IMPORTANT: Always refer to the vehicle manufacturer’s service
instructions, or proprietary manual, to establish the correct procedure and
data for the specific vehicle you are working on. These instructions for use
are provided as a guide only.
INTRODUCTION
Comprehensive kit of tools for the fast and effective removal and installation of wheel bearings on front-wheel drive vehicles. Reduces chances of damage to hub and bearing. Heavy-duty steel drifts with phosphate coating to prevent corrosion. Heavyweight drive screw for use with impact tools. Also suitable for removing and installing large industrial bearings. Supplied in storage case.
SPECIFICATION
| Model No: | VS7020.V3 |
|---|---|
| Drift sizes: | Ø50, 55, 60, 64, 67, 70, 72 (x2), 73, 75, 78, 82, 84, 88mm |
| External sleeve diameter: | Ø76, 86, 92, 101mm |
| Hub screw size: | 210 x 32, 210 x 38mm |
CONTENTS
OPERATION
- HUB SCREW NUT
- WASHER
- DRIFT
- BEARING
- VEHICLE HUB
- SLEEVE
- SLEEVE CAP
- HUB SCREW
BEARING REMOVAL: Identify the correct sleeve (6) to sit on
the Outside of the bearing housing and the correct drift (3) to drive the
Bearing from the housing. Assemble as shown in fig.1A using the correct sleeve
cap (7). Keep the hub screw and nut well lubricated whilst driving out the
bearing.
BEARING INSTALLATION: Identify the
correct sleeve cap (7) to sit on the outside of the bearing housing and the
correct diameter drift (3) to drive the new bearing into the housing. Assemble
as shown in fig.1B. Keep the hub screw and nut well lubricated whilst driving
the new Bearing into the housing. The 50mm end cap is used to locate into the
back of the drifts; they can then be used in a workshop press when it is not
possible to use the hub screw.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers anddispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice. Please note that other versions of this product are available.
If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk
or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way,
Suffolk Business Park,
Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
sales@sealey.co.uk
www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
VS7020.V3 Issue:3
( H,F) 16/01/24
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>