wikiHow B91f25b1 Fixture Installation Guide
- June 1, 2024
- wikiHow
Table of Contents
wikiHow B91f25b1 Fixture
Specifications:
- Item No: CP3627R
- Column Nut
- Cross Bar Box Screw
- Mounting Frame Wood Screw
- Safety Cable With Hook Canopy
- Coupling Set Screw
- Screw Driver Cord
Product Usage Instructions
Fixture Assembly:
Carefully remove the fixture from the carton and ensure all parts are included
as shown in the figure. Avoid misplacing any screws or parts required for
installation.
Installation:
- Secure cross bar onto the outlet box with box screws.
- Grounding Instructions:
- Add a section of bridge wire for every 4 lamp cords by attaching wires accordingly.
- Group remaining cords and wire together and connect them to the main power source from the outlet box.
- Tuck excess wire inside the outlet box and fasten the canopy in place with column nuts.
- Raise the shade, check the ring through the lamp holder, and lock the shade tightly with the check ring.
- Install bulbs (not included) into the lamp holder.
Cleaning:
Wipe the fixture with a soft cloth. Clean glass with mild soap.
Avoid abrasive materials like scouring pads, steel wool, or abrasive paper.
Final Assembly:
- Fasten the mounting frame to the ceiling securely using long thick wood screws.
- Feed the lamp holder’s cord through the bottom coupling of the canopy and tighten the set screw to hold it in place.
- Repeat for each pendant being attached to the canopy.
FAQ:
Q: Can I install this fixture on a ceiling with a radiant type heating
system?
A: No, a swag type fixture should not be installed on a ceiling
containing a radiant type heating system. Consult a qualified electrician for
further guidance.
Q: How do I order replacement parts for this fixture?
A: Keep this sheet for future reference and order replacement parts using
the exact wording from the illustration through the place of purchase.
INSTALLATION AND SAFETY INSTRUCTION
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF. GENERAL: You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling, which contains a radiant type heating system. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Under no circumstances should a fixture be hung on
house electrical wires, nor should a swag type fixture be installed on a
ceiling, which contains a adiant type heating system. Read instructions
carefully. If you are unclear as to how to proceed, consult a qualified
electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.
FIXTURE ASSEMBLY
Carefully removed the fixture from the carton and check that all parts are
included as shown in figure. Be careful not to misplace any of the screws or
parts, which are needed to install this fixture.
INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box.
STEP1: Secure cross bar on to outlet box with box screws.
Proceed to connect wires:
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two raised dimples on the circular strap. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES！
FINAL ASSEMBLY
Step 1: Fasten the mounting frame to ceiling, be sure that the frame is
mounted securely to the building structure using long thick wood screws (Not
included, #10 or greater recommended).
Wood screws should be long enough to be in the wood structure at least 1.5”
(not including frame, drywall/plaster, or wall cladding). When needed refer to
page 2 for extra fastening/safety cable fastening instructions when
applicable.
Step 2: Feed the lamp holder’s cord through the bottom coupling of the canopy. Once fixture is at the desired height, hold it in place by using screw driver to tighten the set screw. Put the buckle on the cord and snug it up to the fitting where the cord comes through the ceiling plate. Repeat for each pendant being attached to the canopy.
Step 3: Add a section of bridge wire for every 4 lamp cords.
This is done by taking a loose piece of wire 1’-2’ in length.
Attach the wires from the 4 lamp cords to one end of the wire (white to white,
black to black, ground to ground).
Step 4: Group the remaining cords and wire together and attach them to the main power source from the outlet box with wire connectors. Once again, white to white and black to black,ground to ground.
Step 5: Tuck excess wire inside of the outlet box. Raise the canopy to the mounting frame, be sure that no loose wires are being pinched. Fasten the canopy in place with column nuts.
Step 6: Raise the shade and check ring through lamp holder and lock the shade with check ring tightly
Step 7: Install the bulbs(Not included) into the lamp holder.
CLEANING
To clean wipe fixture with a soft cloth. Clean glass with a mild soap. Do not
use abrasive materials such as scouring pads or powders, steel wool or
abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when ordering parts.
Line art shown may not exactly match the fixture enclosed.
However, the installations do apply to this fixture.
ITEM NO: CP3627R
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>