PERFORMANCE DIY Ab Certified Rejection Kit for Counter Tops User Manual

: June 1, 2024
: PERFORMANCE DIY

Table of Contents

PERFORMANCE DIY Ab Certified Rejection Kit for Counter Tops
Specifications
FAQ
Description
Product Using Instruction
Contact
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PERFORMANCE DIY Ab Certified Rejection Kit for Counter Tops

PERFORMANCE-DIY-Ab-Certified-Rejection-Kit-for-Counter-Tops-
product

Date of Issue: 12-15-23

For technical support, contact us Monday-Friday 9-5PM, and Saturday 11-3PM EST at 800-841-5580 EST or visit www.PerformanceDIY.com.

Step by Step Instructions: Preparation

Step 1:

Recommended but not necessary to work in a ventilated room; (do not work near heat or flames if using Poly 300 Polyspartic clear). Clean surfaces; remove any debris from countertop areas.

Step 2:

Sand the surface with the supplied sanding paper. Wipe clean with rags to remove any sanding dust and debris. Fill fine cracks with PerformanceDIY.com caulk.

Step 3: Prime Coat

Mix Part “A” in its original container for 2 minutes. Pour all of Part “B” into a large clean container. Pour all of Part “A” into the same container. Mix thoroughly for 3 minutes with the mixing tool for 3 minutes, paying close attention to all around the bucket sides and rising and lowering the mixing tool.

Step 4:

Using the supplied squeegee spread the base coating material evenly over the counter to the area, then clean the squeegee well with a rag and xylene, as you will need it in step 9: DO NOT SOAK IN XYLENE THIS WILL DESTROY THE SQUEEGEE.

Step 5:

Using the supplied 4″ roller, roll out the base coating material evenly over the counter to area and the outer perimeter.

Step 6:

After the entire base coat has been applied evenly, apply the decorative flake chips conservatively, assuring even full coverage of flake chips. Two coats may be necessary on vertical surfaces.

Step 7:

After 24 hrs. the excess flakes can be removed, and the remaining flakes sanded to remove any high areas or excessive flakes to create a smooth surface. Lightly sand the surface with the supplied sanding block. Clean the surface after sanding.

Clear Epoxy Application

Step 8:

Mix Part “A” in its original container for 2 minutes. Pour all of Part “B” into a large clean container. Pour all of Part “A” into the same container. Mix thoroughly for 3 minutes with the mixing tool for 3 minutes, paying close attention to all around the bucket sides and rising and lowering the mixing tool.

Step 9:

Using the supplied squeegee spread the base coating material evenly over the counter to area, clean the squeegee well with a rag and xylene, as you will need it in step 9: DO NOT SOAK IN XYLENE THIS WILL DESTROY THE SQUEEGEE.

Step 10:

Using the supplied 4″ roller, roll out the base coating material evenly over the counter to area and the outer perimeter. Do not over roll, this can create bubbles. Use a small torch to reduce bubbles by waving flame quickly over bubbled surface. Counter can be used within 24 hours, careful use for 3 full days.

Specifications

Property	Details
Address	169 N. Gratiot – Mt. Clemens, MI 48043
Contact Information	Office:

800-841-5580, Fax: 586-468-844
Surface Coatings| Garage, Basement, Deck & Patio, Driveways, Paver Coating, Counter Tops, Concrete Patch, Crafts

FAQ

What should I do if I notice bubbles in the coating?
- Use a small torch to reduce bubbles by waving flame quickly over the bubbled surface.
How soon can I use my counter after application?
- The counter can be used within 24 hours, but for best results, careful use is recommended for 3 full days.
Is it necessary to work in a ventilated room?
- It is recommended but not necessary unless using Poly 300 Polyspartic clear. Always avoid working near heat or flames.
Can the epoxy be applied to vertical surfaces?
- Yes, ensure even coverage of flake chips, and two coats may be necessary on vertical surfaces.

Description

PERFORMANCE-DIY-Ab-Certified-Rejection-Kit-for-Counter-Tops-
fig-1

Product Using Instruction

Step 1:
- Recommended but not necessary to work in a ventilated room; (do not work near heat or flames if using Poly 300 Polyaspartic clear). Clean surfaces; remove any debris from countertop areas.
Step 2:
- Sand the surface with the supplied sanding paper. Wipe clean with rags to remove any sanding dust and debris. Fill fine cracks with PerformanceDIY.com caulk.
Step 3: Prime Coat
- Mix Part “A” in its original container for 2 minutes. Pour all of Part “B” into large clean container. Pour all of Part “A” into same container. Mix thoroughly for 3 minutes with the mixing tool for 3 minutes, paying close attention to all around the bucket’s sides and rising and lowering the mixing tool.
Step 4:
- Using the supplied squeegee spread the base coating material evenly over the counter to area, clean the squeegee well with a rag and xylene, as you will need it in step 9: DO NOT SOAK IN XYLENE THIS WILL DESTROY THE SQUEEGEE.
Step 5:
- Using the supplied 4″ roller, roll out the base coating material evenly over the counter to area and the outer perimeter.
Step 6:
- After the entire base coat has been applied evenly, Apply the decorative flake chips conservatively, assuring even full coverage of flake chips. Two coats may be necessary on vertical surfaces.
Step 7:
- After 24 hrs. the excess flakes can be removed, and the remaining flakes sanded to remove any high areas or excessive flake to create a smooth surface. Lightly sand the surface with supplied sanding block. Clean surface after sanding.
  Clear Epoxy Application
Step 8:
- Mix Part “A” in its original container for 2 minutes. Pour all of Part “B” into large clean container. Pour all of Part “A” into same container. Mix thoroughly for 3 minutes with the mixing tool for 3 minutes, paying close attention to all around the buckets sides and rising and lowering the mixing tool.
Step 9:
- Using the supplied squeegee spread the base coating material evenly over the counter to area, clean the squeegee well with a rag and xylene, as you will need it in step 9: DO NOT SOAK IN XYLENE THIS WILL DESTROY THE SQUEEGEE.
Step 10:
- Using the supplied 4″ roller, roll out the base coating material evenly over the counter to area and the outer perimeter. Do not over roll, this can create bubbles. Use small torch to reduce bubbles by waving flame quickly over bubbled surface. Counter can be used within 24 hours, Careful use for 3 full days.