PERFORMANCE DIY 12-15-23 Kraft Coat Craft Coating Instruction Manual

: June 1, 2024
: PERFORMANCE DIY

Table of Contents

PERFORMANCE DIY 12-15-23 Kraft Coat Craft Coating
Product Information
Preparation
Clear Coat Application
Optional Poly 200 Clear Topcoat
Contact
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PERFORMANCE DIY 12-15-23 Kraft Coat Craft Coating

PERFORMANCE-DIY-12-15-23Kraft-CoatCraft-Coating-
product

Product Information

Specifications

Product Name: Performance DIY Epoxy Coating Kit
Application: Solid Color Coat, Metallic Coat, Clear Coat
Optional: Poly 200 Clear Topcoat for UV Protection

FAQ

Q: How long does it take for the epoxy coating to dry?
- A: The drying time can vary depending on temperature and humidity levels. It is recommended to allow at least 24 hours for the coating to fully cure.
Q: Can I apply multiple coats of epoxy for a thicker finish?
- A: Yes, you can repeat the application steps for additional coats to achieve a thicker finish.

Preparation

Step 1:
- Clean surfaces; remove any debris from areas. Mix part “A” Resin.
Step 2:
- Sand the surface with the supplied sanding paper. Wipe clean with rags to remove any sanding dust and debris.

Solid Color Coat application

Step 1: 1st Color Coat
- Pour all of Part “B” into larger clean container. Pour all of Part “A” base coat (colored) into same container. Mix thoroughly for 3 minutes with the mixing tool or mixing stick for 3 minutes, paying close attention to all around the buckets sides and rising and lowering the mixing tool.
Step 2:
- Spread the color coating material evenly over the area, clean the squeegee (if used) well with a rag and xylene, as you may need it in the future: DO NOT SOAK IN XYLENE THIS WILL DESTROY THE SQUEEGEE. Using the supplied 4” roller, roll out the base coating material evenly over the area and the outer perimeter. Use small torch to reduce
Step 3:
- After 24 hrs. sand with 800+ grit to remove any high areas or inconsistencies to create a smooth surface.

Metallic Coat Application

Note

A solid color is often used as a base coat application for metallic applications, see above application instructions.

Step 1:

Pour all of Part “B” into large clean container. Pour all of Part “A” pre-mix metallic resin into same container.
Mix thoroughly for 3 minutes with the mixing tool for 3 minutes, paying close attention to all around the buckets sides and rising and lowering the mixing tool.

Step 2

Using the supplied 1/8″ squeegee spread the metallic coating material evenly over the counter to area, clean the squeegee well with a rag and xylene, as you will need it in step 8: DO NOT SOAK IN XYLENE THIS WILL DESTROY THE SQUEEGEE. Using the supplied 4″ roller, roll out the base coating material evenly over the counter top area and the outer perimeter. Use small torch to reduce bubbles.

Optional:

Step 3:

After 24 hrs. sand with 800+ grit to remove any high areas or inconsistencies to create a smooth surface. Repeat steps application steps 1-2 with either metallic or clear coat epoxy.

Clear Coat Application

Step 1:

Pour all of Part “B” into larger clean container. Pour all of Part “A” base coat (clear) into same container. Mix thoroughly for 3 minutes with the mixing tool or mixing stick for 3 minutes, paying close attention to all around the buckets sides and rising and lowering the mixing tool.

Step 2:

Spread the base coating material evenly over the area, clean the squeegee (if used) well with a rag and xylene, as you may need it in the future: DO NOT SOAK IN XYLENE THIS WILL DESTROY THE SQUEEGEE. Using the supplied 4″ roller, roll out the base coating material evenly over the area and the outer perimeter. Use small torch to reduce bub- bles by waving flame quickly over bubbled surface.

Optional:

Step 3:

After 24 hrs. sand with 800+ grit to remove any high areas or inconsistencies to create a smooth surface.
Repeat steps application steps 1-2.

Optional Poly 200 Clear Topcoat

(UV Protection) allow 10 to 24 hours to pass before applying.
No mixing required, simply brush and roller apply (odors will be present for 12 hours, must be ventilated)
Optional Poly 200 Polyaspartic clear for more resistance and UV stability can be purchased at PerformanceDIY.com.