Fudajo 52430 Chicken Coop with Outdoor Run and Nesting Box Installation Guide
- June 1, 2024
- Fudajo
Table of Contents
Fudajo 52430 Chicken Coop with Outdoor Run and Nesting Box
Product Information
Parts and Diagrams
Nr. | Avbildning | Nr. | Avbildning | Nr. | Avbildning | Nr. | Avbildning |
---|---|---|---|---|---|---|---|
1 | Image of a small structure | 11 | Wire mesh panel | 12 | Corner piece | 2 | Wire |
mesh grid
3| Image of the structure with an open hatch| 13| Flat rectangular panel| 14|
Flat square panel| 4| Structure with door frame
5| Structure with a slanted roof| 15| Wire mesh frame| 16| Flat roof panel| 6|
Wire mesh door
7| Large wire mesh panel| 17| Long rectangular panel| 18| Long pole| 8| Wire
mesh grid
9| Structure with a rectangular base| 19| Door with a lock| 20| Long pole| 10|
Lock mechanism
Specifications
Item | Description | Dimensions | Quantity |
---|---|---|---|
A | Screw | 3.5×60 | 4 |
Screw | 3.0×16 | 6 | |
B | Screw | 3.5×50 | 20 |
C | Screw | 3.5×35 | 12 |
D | Screw | 3.0×25 | 4 |
F | Bolt | M6x60 | 8 |
G | Hook | 1 |
- Product Model: 52430
- Number of Steps: 11
- Page Number: 07 2023-1
Product Usage Instructions
Step 1: Assembly
Begin by arranging the components according to the numbered illustrations
provided in the manual.
Assembly Steps
-
Step 1 Assemble the base of the structure with multiple B screws.
Note: Part 2 has two cutouts and is the bottom part of the front panel. -
Step 2 Attach the roof and side panels using B screws and secure the wire mesh door, part 19.
Note: Part 19 is the door and is the lower part of the back panel. -
Step 3 Install the rear and side wire mesh panels, securing them with A screws.
-
Step 4 Complete the roof assembly with E panels and fasten using E screws.
-
Step 5 Continue building the structure by adding additional B screws and wire mesh panels.
-
Step 6 Add the upper structure panels, securing with F screws and attach the door, part 9.
-
Step 7 Secure the front panels with F screws and attach the lock mechanism, part 10.
-
Step 8 Install the remaining roof panels, securing with I screws and add the pole, part 20.
-
Step 9 Finalize the roof assembly with E panels and E screws.
-
Step 10 Attach the last set of C panels to the roof structure, using C screws.
-
Step 11 Finish the assembly by securing the roof with D screws and installing the hook, part G.
Step 2: Front Panel Installation
Attach the front panel securely following the guidelines outlined in the
manual.
Step 3: Next Step Title
Description of the third step in detail…
Step 4: Following Steps
Continue with the assembly process by following the subsequent steps as
indicated.
Step 5: Additional Steps
Carry on with the assembly process by completing the additional steps
mentioned.
© by WilTec Wildanger Technik GmbH
Article 52430
For more information, visit www.fudajo.com
Important Notice:
Any form of reproduction, distribution, or commercial use of these
instructions requires written permission from WilTec Wildanger Technik GmbH.
FAQ (Frequently Asked Questions)
What should I do if a part is missing?
In case of any missing parts, please contact our customer support for
assistance in obtaining the necessary components.
How can I clean the product?
To clean the product, use a soft cloth dampened with a mild detergent.
Avoid using abrasive cleaners that may damage the surface.
Where can I find more information about the parts?
Refer to the parts and diagrams section and specifications table for details
about the parts.
What should I do if I’m missing a part?
Contact the manufacturer or visit www.fudajo.com for
assistance.
How can I ensure the structure is stable?
Follow the assembly steps closely and make sure all screws are tightly
fastened.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>